2GIG PIR100-345 - Installation Guide - 2025

A
B
C
D
A
PRINTER’S INSTRUCTIONS
INSTR, INSTL, 2GIG-PIR100-345, ENGLISH - P/N: 10034947 Rev-A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 17.000” - TOL. +/- 0.020”- SCALE: 1-1 - FOLDING: FOLD FOUR TIMES TO: 2.83" x 2.75"
Passive Infrared Motion Detector

with Enhanced Security
General Information
The 2GIG Passive Infrared Motion Detector (2GIG-PIR100-345) is a
wall mounted unit with wide-angle motion protection and enhanced
wireless range with encrypted communications to the control panel
using the 345Mhz frequency. The PIR has a maximum range of 30 ft
deep x 50 ft wide (9.1 m x 15.2 m). The Pet-immune feature can be
set to tolerate animals up 85 lbs (38 kg).
Figure 1
Passive Infrared Motion Detector

•
(1) Passive Infrared Motion Detector (Part A)

•
(1) Plastic Mounting Bracket (Part B)

•
(1) Plastic Wall Mount (Part C)

•
(1) Plastic Corner Mount (Part D)

•
(2) Plastic Wall Anchors With Screws (not pictured)

•
(1) Short Phillips Head Screw with Fender (not pictured)

•
(1) Short Phillips Head Screw (not pictured)

•
(1) Lithium CR123A Battery (not pictured)
Box Contents
Verify that the package includes the following (see
Figure 3 PIR and
Mounting Bracket Detail on page 2, Figure 3)
:
Battery Installation and Replacement
To insert or replace the battery:
1
Remove the front cover using a bottom-to-top lifting motion.
2
Insert the battery. Please make sure to follow correct polarity for
proper functioning (positive side to the right).
3
Replace the PIR cover.
WARNING:
Failure to follow these warnings and instructions can lead
to heat generation, rupture, leakage, explosion, fire, or other injury, or
damage. Do not insert the battery into the compartment in the wrong
direction. Always replace the battery with the same or equivalent type
(see
Specifications
on page 4). Never recharge or disassemble the
battery. Never place the battery in fire or water. Always keep batteries
away from small children. If batteries are swallowed, promptly see a
doctor.

•
Always dispose and/or recycle used batteries in accordance
with the hazardous waste recovery and recycling regulations
for your location. Your city, state, or country may also require
you to comply with additional handling, recycling, and disposal
requirements.
Configuring the PIR Features
Configure the features as follows:
Figure 2
PIR Pet Immune and Sensitivity Features
Setting the Pet Immune Feature
To set the pet immune feature:
NOTE:
Do not aim the PIR at stairs, furniture, or other surfaces that a pet may
climb on. The PIR provides immunity when the room temperature is above
50° F (10° C) and below 90° F (32° C). When mounting the PIR with the plastic
mounting bracket, for best protection ensure the PIR is mounted to the wall or
corner with NO tilt (see
Lens Pattern
and
Tilt Angles
on page 3).
1
Remove the sensor from mounting plate, locate the right switch on
the bottom right (see Figure 2, C). The default position is OFF. See
Figure 2 PIR Pet Immune and Sensitivity Features
.
2
Gently move the switch to ON position to enable pet-immune setting.
Encryption Mode Switch
The sensor is capable of transmitting signals in
Encrypted mode
or
Non-
encrypted mode
. The mode is set through a switch inside the sensor
(See Figure 2).
By default, the factory setting is non-Encrypted mode. To change to
Encryption mode, do the following:
1
With the front cover off, remove battery from the slot
2
Locate the dip switch directly above battery compartment (see A
in Figure 2), and note the switch setting:
ON
indicates
encrypted,

and
1
is
non-encrypted
mode. Move the switch position to
ON
for
encrypted mode.
3
Insert the battery back, and close the housing.
4
If the sensor was learned in to a panel in a different mode previously,
update sensor class field, and if applicable, sensor equipment co
de
in sensor zone programing.
T
AMPER
PET
ON/
OFF
E
A
B
D
C
2GIG-PIR100-345
2
1
Option A: Bracket Mounting
See
Figure 3 PIR and Mounting Bracket Detail
. If you plan to mount the
PIR to either the Plastic Wall Mount or Plastic Corner Mount, you must
first attach the Plastic Mounting Bracket to the PIR backplate.
Step 1: Attaching the Plastic Mounting Bracket to the PIR
1
Remove the PIR backplate.
2
Insert the two stubs on the Plastic Mounting Bracket into the
corresponding holes on the exterior side of the PIR backplate.
3
On the interior of the PIR backplate (see
Figure 4 PIR Backplate—
Direct-to-Wall Mounting Guides
), use the Short Phillips Head Screw
(provided) to secure the Plastic Mounting Bracket to the backplate.
4
Replace the PIR backplate.
5
Reattach the screw that was removed earlier to the bottom of the PIR.
6
Continue with either
Step 2a: Wall Mounting Option or Step 2b:
Corner Mounting Option
.
NOTE:
For optimum pet immunity when using the Plastic Mounting Bracket,
ensure that the PIR is mounted to the wall or corner with NO tilt (see
Lens
Pattern
and
Tilt Angles
on page 3).
Step 2a: Wall Mounting Option
See
Figure 3 PIR and Mounting Bracket Detail
. If using the Plastic Wall
Mount (C), do the following:
NOTE:
Ensure that you have attached the bracket to the PIR backplate
(
see
Step 1: Attaching the Plastic Mounting Bracket to the PIR)
.
1
On the intended wall, use the two (2) Plastic Wall Anchors to hang
the Plastic Wall Mount at a height of 7.5 ft. (2.3 m).
2
Locate the barrel end of the Plastic Mounting Bracket. Locate the
barrel end of the Plastic Mounting Bracket and carefully set it onto
the ribbed pin of the Plastic Wall Mount at the desired angle (see
Lens Pattern and Tilt Angles on page 3
).
3
From the topside of the Plastic Wall Mount, use the Short Phillips
Head Screw with Fender (provided) to secure the mount to the
barrel end of the bracket.
Step 2b: Corner Mounting Option
See
Figure 3 PIR and Mounting Bracket Detail
. If using Plastic Corner
Mount, do the following:
NOTE:
Ensure that you have attached the bracket to the PIR backplate
(
see
Step 1: Attaching the Plastic Mounting Bracket to the PIR
on page 2).
1
Use the two (2) Plastic Wall Anchors to hang the Plastic Corner
Mount at a height of 7.5 ft (2.3 m).
2
Locate the barrel end of the Plastic Mounting Bracket and
carefully set it onto the ribbed pin of the Plastic Wall Mount.
Ensure that you set it at the desired angle (see
Lens Pattern and
Tilt Angles on page 3
).
3
From the topside of the Plastic Wall Mount, use the Short Phillips
Head Screw with Fender (provided) to secure the mount to the
barrel end of the bracket.
Option B: Direct-to-Wall Mounting
If planning to mount the PIR directly to a wall, use the built-in
mounting guides on interior of the PIR backplate to screw the
backplate into the wall.
1
Remove the PIR backplate.
2
Use the two (2) Plastic Wall Anchors to screw the PIR backplate
into the wall at a height of 7.5 (2.3 m):

•
Use the wall mounting guides (see B below).

•
Corner Mount. Use the left- or right- corner mounting guides
(see A below).
Figure 4
PIR Backplate—Direct-to-Wall Mounting Guides
A
Corner Mounting Guides (For
Option B: Direct-to-Wall Mounting
)
B
Wall Mounting Guides (For
Option B: Direct-to-Wall Mounting
)
C
Wall Mount Bracket Guide (For
Option A: Bracket Mountin
g)
Programming
The following steps describe general guidelines for programming
(Learning) the sensor into the alarm control panel memory. For details,
refer to the
2GIG Panel Installation & Programming Instructions
.
1
Put the panel in sensor Learn mode.
2
Install batteries in the sensor. After the sensor is powered on,
tamper the sensor to complete learn-in process.
IMPORTANT:
The following can cause a false alarm when testing:
• Leaving the cover off • Positioning the PIR in direct sunlight or close
proximity to a heating or an air conditioning duct.
Local Testing
This test ensures that the PIR sees motion in the desired areas. Please
note that PIR does not transmit motion trigger events to the panel while
in test mode.
1
Press and hold the
Test
button for 2 seconds (Figure 2, D) to enter
local test mode. The LED will blink twice to acknowledge being in
test mode.
2
Place the PIR in the preferred mounting location.
3
Move something to the area that is to be covered by the PIR, and
make sure that the LED on the PIR flashes every time you move.
There is a 3 second delay between sensor looking for motion and
lighting the LED. The test mode continues for 10 minutes, so you
have time to check the PIR beam coverage.
4
If you're using the included mounting bracket, adjust the PIR left
or right, down 1 or 2 clicks, or up 1 click, to see movement in the
desired area(s). Each click represents 9° tilt.
5
The sensor automatically resumes normal operation after 10
minutes, or immediately upon pressing the test button.
Mounting Guidelines
Before mounting the detector, ensure that the PIR mounting location
provides good RF communication to the panel. There are two methods
for mounting the PIR: Option A: Bracket Mounting or Option B: Direct-
to-Wall Mounting. For both methods, always mount the PIR at a height
of 7.5 ft (2.3 m).
Figure 3
PIR and Mounting Bracket Detail
A
Tamper Switch:
Sends a Tamper message when the sensor's housing
is opened.
B
Encrypted/Non-encrypted Mode Switch: ON
setting indicates
Encrypted,
and
1
setting is
Non-encrypted
mode.
C
Pet:
This is the pet-immune tolerance setting. Setting it to
ON
enables
pet immunity up to 85 lbs.
OFF
position (default) disables pet immunity.
D
Test Button:
Initiates local Test mode.
E
Backplate Tamper
A
PIR
B
Plastic Mounting Bracket
C
Plastic Wall Mount
D
Plastic Corner Mount Environmental & Other Useful Information
While the PIR is a highly reliable intrusion detection device, it does not
guarantee against burglary. Any intrusion device is subject to a “failure
to warn” for a variety of reasons. Consider the following when installing
and setting up the PIR:
1
Infrared energy can be reflected off any glossy surfaces such as
mirrors, windows, floors, or counter tops with glossy finish, and
slick-finished concrete. Some surfaces reflect less than others (e.g.
the PIR can see a change in infrared energy off of reflective surfaces
even if the heat or cold source is not within the PIR detection
pattern).
2
Windows reflect infrared energy. They also allow sunlight or light
from other sources (e.g., cars) to pass through to the PIR. The PIR
can detect these changes in infrared energy. For example, if sunlight
passing through a window shines onto a hardwood floor and the
change in infrared energy is quick enough, the PIR can trigger an
alarm. The same applies if the PIR area includes a window, even
though the pattern of protection cannot “see” through glass. Lights
from a passing car can also pass through the window at night and
shine directly into the PIR’s lens.
3
Heating and air conditioning ducts are also important because if
they blow air onto an object within the field of the PIR’s view, the
temperature of that object could change quickly enough for the PIR
to “see” a change in infrared energy.
PIR’s cannot see air current,
only the change in temperature of a physical object.
4
The PIR senses change in temperature. However, as the ambient
temperature of the protected area approaches the temperature
range of 95° to 120° F, the detection performance of the PIR
decreases.
5
Ensure that the area you wish the PIR to cover is free of
obstructions (for example, curtains, screens, plants, and so on) that
may block the pattern of coverage.
6
Anything that can sway or move due to air current can cause a
change in infrared energy within the fields of view. Drafts from doors
or windows can cause this to happen. Plants, balloons, curtains, and
hanging baskets should never be left in the PIR’s field of view.
7
Do not mount the PIR on a surface that allows for any vibration.
Vibrations not only cause the PIR to move a little, but it also causes
the fields of view in a room to move with respect the PIR. A little
vibration can cause havoc with the PIR’s field of view, thus the PIR
may see a change in energy and trigger the alarm.
8
An installation often requires that the PIR is aimed at the door.
The PIR may detect door movement before the door contact can
initiate an entry delay, causing the alarm to trigger. If you install
the PIR facing a door, then while programming the PIR, choose an
appropriate sensor/zone type.
9
The PIR ONLY detects intrusion within the pattern of coverage.
10
The PIR does not provide volumetric area protection.
11
The PIR creates multiple beams of protection. Intrusion can only be
detected in unobstructed areas covered by those beams.
12
The PIR cannot detect motion or intrusion that occurs behind walls,
ceilings, floors, closed doors, partitions, glass doors, or window
s.
13
Tampering with, masking, painting, or spraying of any material on the
PIR lens or any part of the optical system can impair detection ability.
14
The PIR, like other electrical devices, are subject to component
failure. Even though the PIR is designed to last as long as 10 years,
the electronic components are subject to failure.
Lens Pattern and Tilt Angles
The diagrams below show the lens pattern and tilt angles for the PIR in
meters.
Figure 5
Lens Pattern—Top View
0m
1m
2m
3m
4m
5m
6m
7m
8m
9m
10m
11m
12m
13m
50º
40º
30º
20º
10º
10º
20º
30º
40º
50º
0º
90º
7m 6m 5m 4m 3m 2m 1m
1m 2m 3m 4m 5m 6m 7m
8 - 9m
0m 1m 2m 3m 4m 5m 6m 7m 8m 9m 10m 11m 12m 13m
0m 1m 2m 3m 4m 5m 6m 7m 8m 9m 10m 11m 12m 13m
0m 1m 2m 3m 4m 5m 6m 7m 8m 9m 10m 11m 12m 13m
0m 1m 2m 3m 4m 5m 6m 7m 8m 9m 10m 11m 12m 13m
1m
2.3m
-18º
1m
2.3m
-9º
1m
2.3m
9º
1m
2.3m
0º
Figure 6
Lens Pattern—Side View
3
Limited Warranty
This Nice North America LLC product is warranted against defects
in material and workmanship for two (2) years. This warranty extends
only to wholesale customers who buy direct from Nice or through
Nice’s normal distribution channels. Nice does not warrant this
product to consumers. Consumers should inquire from their selling
dealer as to the nature of the dealer’s warranty, if any.
There are no obligations or liabilities on the part of Nice for
consequential damages arising out of or in connection with use or
performance of this product or other indirect damages with respect
to loss of property, revenue, or profit, or cost of removal, installation
or reinstallation. All implied warranties for functionality, are valid only
until the warranty expires. This Nice Warranty is in lieu of all other
warranties expressed or implied.
Industry Canada (IC) Compliance
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause
undesired operation of the device.
Regulatory Information
We, Nice North America, LLC of 5919 Sea Otter Place STE 100,
Carlsbad, CA 92010, declare under our sole responsibility that the
device, 2GIG-PIR100-345 complies with Part 15 of the FCC rules.
FCC & IC Notice
This device complies with Part 15 of the FCC Rules and Industry
Canada license exempt standard(s). Operation is subject to the
following two conditions:
1
This device may not cause harmful interference, and
2
The device must accept any interference received, including
interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

•
Reorient or relocate the receiving antenna.

•
Increase the separation between the equipment and receiver.

•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

•
Consult the dealer or an experienced radio/TV technician for help.
FCC
Federal Communication Commission (FCC) Radiation Exposure
Statement:
When using the product, maintain a distance of 20cm from the body
to ensure compliance with RF exposure requirements.
IC
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your
body.
WARNING:
Changes or modifications not expressly approved by the
manufacturer could void the user’s authority to operate the equipment.
Code Outputs
Alarm, Alarm Restore, Tamper, Tamper
Restore, Supervisory, Low Battery
Transmitter Frequency
345MHz
Supervisory Interval
70 minutes
Sensor Type
Quad element
Pet Immunity Selectable
Dip Switch, up to 85 lbs (38 kg)
Suggested Mounting Height
7.5 ft (2.3 m)
Sensor Range
30 ft (9.1 m) x 50 ft (15.2 m)
Max. Horizontal Sensing Angle
100°
Dimensions (L x W x H)
3.53" x 2.35" x 1.63" (5.4 x 6 x 4.1 cm)
Weight (including battery)
98g
Housing Material
ABS Plastic
Color
White
Operating Temperature
32°-120 F° (0°-49° C)
Relative Humidity
5-90% Non-Condensing
Battery (included)
One (1) CR 123A 3V or equivalent
Lithium battery
Certification
ETL, FCC and IC
Panel Programming Sensor Loop
Loop 1
Sensor Equipment Code
(encrypted)
2869
Sensor Equipment Code
(non-encrypted)
0869
Customer Service
760-438-7000
Monday – Friday, 5:00 a.m. – 4:30 p.m. PST
Saturday, 7:00 a.m. – 3:30 p.m. PST
www.2gig.com
Nice North America LLC
5919 Sea Otter Place, Suite 100
Carlsbad, CA 92010
Niceforyou.com
©2025 Nice North America LLC. 2GIG is a registered trademark of Nice North America LLC. All rights reserved.
10034947 Rev-A
Specifications