2GIG RPTR100-345 - Installation Guide - 2025

1
PRINTER’S INSTRUCTIONS:
INSTR, INSTL, 2GIG-RPTR100-345 - P/N: 10034956 Rev-A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.5000” X 11.000” - TOL. +/- 0.125”- SCALE: 1-1 - PAGE 1 OF 2-
FOLDING: FOLD 4X TO FINAL SIZE: 2.125" X 2.750"- FINISH WITH LOGO SHOWING
H
G
F
E
B
A
C
D
OBSERVE
BATTERY
POLARITY
1
3
2
4
5
6
7
8
9
Installing the Repeater
Figure 2.
Wireless Indoor Repeater Component and Feature Locations
General Information
The 2GIG
®
Wireless Indoor Repeater (2GIG-RPTR100-345) a peripheral
device that receives and recognizes messages from other 2GIG 345
MHz devices that are unable to directly communicate with the system,
and “repeats” those messages to extend the range of these devices.
The Repeater offers flexible signal transmission options, supporting
both encrypted and non-encrypted modes, and is compatible with 2GIG
wireless alarm systems.
The repeater is typically installed midway between the panel and the
wireless devices to be repeated. When a transmission from a device
is repeated, the repeater adds a bit to the message to indicate to the
system that the message is not coming directly from the device. The
repeater will not repeat already repeated messages.
The repeater is powered by an AC adapter and includes a rechargeable
battery, providing 24-hour backup during local power outages. When
switching between AC power and battery backup, the repeater
automatically notifies the panel within 2 minutes. Additionally, it sends
supervisory status updates approximately every 70 minutes.
The repeater is equipped with a status indicator LED visible from the front
of the unit, and a learn button is located on the side of the unit.
Figure 1.
Wireless Indoor Repeater Package Contents
Mounting Guidelines
Use these guidelines when installing the wireless indoor repeater:
•
Mount Repeaters within 100 ft (30 m) of the Control Panel.
Although
the transmitter may have a range of 350 ft (106 m) in open air, the
repeater location can have a significant effect on range. In open/
unobstructed spaces, the transmitter range may be greater. In
adverse wireless conditions, changing the repeater orientation can
improve performance.
•
Mount Repeaters as high as possible.
Mounting the repeater high off
the ground helps receiver sensitivity.
•
Do Not Expose Repeaters to Moisture or Extreme Temperature.

It is best to mount repeaters in a dry location where the operating
temperature does not exceed 32° to 120° F (0° to 49° C).
•
Keep Repeaters Away from Metal/Metallic Surfaces.
To keep the
repeater away from metal or metallic surfaces (for example, foil
wallpaper), it is recommended that you use spacers (not included).
You should also avoid mounting sensors in areas where there is a
large quantity of metal or electrical wiring (for example, near a furnace
or in a utility room).
A
Rechargeable Lithium-Ion
Battery
B
AC Adapter
C
Tamper Screw
D
Mounting Screws and
Anchors (4)
E
Learn Button
F
Status Indicator
G
Power Input
H
Case Locking Screw
Installing the Battery
The rechargeable battery can be installed by opening the enclosure while
the power is disconnected (see Figure 2).
WARNING:
Observe battery polarity carefully. Align the battery with the
polarity indicators on the circuit board. Incorrect installation may cause
heat, explosion, or fire, leading to personal injury.
Encrypted/Unencrypted Mode Switch
The sensor is capable of transmitting signals in encrypted mode or
unencrypted mode. The mode is set through a switch inside the sensor
(see Figure 2).
By default, the factory setting is non-Encrypted mode. To change to
Encryption mode, do the following:
1.
With the front cover off, remove the battery from the slot.
2.
Locate the dip switch directly above the battery compartment (see
Figure 2) and note the switch setting:
ON
indicates
encrypted
,
and
1
is
non-encrypted
mode. Move the switch position to
ON
for
encrypted mode.
3.
Wait at least 10 seconds, then reinsert battery and close the
housing.
4.
If the sensor was previously learned into a panel in a different
mode, update the sensor class field and, if applicable, the sensor
equipment code in sensor zone programming.
1.
Rechargeable Lithium-Ion
Battery
2.
Encryption Switch
3.
Tamper Switch
4.
Power Input Connector
5.
Learn Button
6.
Repeater Base
7.
Tamper Screw
8.
Mounting Screws (4)
9.
Mounting Anchors (4)
To install the wireless repeater:
1.
Open the repeater case.
2.
Attach the base to the desired wall location with the four (4) Phillips
head screws and anchors supplied (see Figure 2).
3.
Install the tamper screw (see Figure 2). With the tamper screw
installed, removing the case from the wall triggers tamper.
NOTE:
For the tamper to work correctly, the tamper screw must be
installed into a wall stud. Do not use a wall anchor.
4.
Install the battery.
Observe battery polarity
.
5.
Connect the 2-conductor wire to the power supply and to the
terminal connector on the circuit board. Make sure the wire
passes through the grommet and hole on the repeater base before
connecting to the terminal.
6.
Attach the repeater cover to the base and secure the assembly with
the Phillips head case locking screw.


Wireless Indoor Repeater
2GIG-RPTR100-345 2
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes:
(1)
l’appareil ne doit pas produire de brouillage, et
(2)
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician to help.
Federal Communication Commission (FCC) Radiation Exposure Statement
When using the product, maintain a distance of 20cm from the body to ensure compliance with RF
exposure requirements.
IC RF exposure Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your
body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la
source de rayonnement et votre corps.
Warning
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
* For more warranty and compliance information, visit out website at
www.2gig.com
Limited Warranty
This Nice North America LLC product is warranted against defects in material and workmanship for two (2)
years. This warranty extends only to wholesale customers who buy direct from Nice North America LLC or
through Nice North America LLC’s normal distribution channels. Nice North America LLC does not warrant
this product to consumers. Consumers should inquire from their selling dealer as to the nature of the
dealer’s warranty, if any.
There are no obligations or liabilities on the part of Nice North America LLC for consequential damages
arising out of or in connection with use or performance of this product or other indirect damages with
respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied
warranties for functionality, are valid only until the warranty expires. This Nice North America LLC Warranty
is in lieu of all other warranties expressed or implied.
7.
Plug the AC adapter into an AC outlet. The status indicator will emit
a steady green light.
NOTE:
Do not connect the AC adapter to an AC outlet that is
controlled by a switch.
8.
Once the repeater is powered up, it begins repeating all unrepeated
345 MHz 2GIG transmissions.
WARNING:
This device is not designed to repeat signals from life
safety devices such as Smoke or CO detectors.
ATTENTION
: Cet appareil est conçu pour ne pas répéter les signaux
provenant des dispositifs de sécurité de la vie tels que la fumée ou les
détecteurs de CO.
Status Indications
The status indicator shows the repeater status as follows:
•
Steady Green:
The repeater is AC powered, and the backup battery
is good.
•
Solid Red:
Tamper or AC power failure.
•
Slow Flashing Red:
Low battery.
•
Fast Flashing Red:
Jammed.
•
Blink off:
Transmission received.
Specifications
Supervisory Interval
70 minutes
Overall Size
102 x 76 x 46mm (4.0” x 3.0” x 1.8”)
Material
High-impact ABS plastic
Color
White
Weight (without battery)
125 g (4.4 oz.)
Installation Type
Wall mounted
Operating Frequency
345 MHz
Operating Temperature Limits
-10° C to 55° C (14° F to 131 ° F)
Relative Humidity
5 to 85% non-condensing
Power Type
Remotely powered by AC adapter,
with internal battery backup
AC Adapter Nominal Input
Voltage
100–240 VAC 50/60 Hz
AC Adapter Nominal Output
Voltage
14 VDC
Maximum Power Consumption
3 W
Idle Current
40mA
Operating Current (repeating)
75mA
Storage Device Capacity
800 mAh (1) 3.7V 800 mAh 14500
Type Li-ion battery (not to be
replaced)
Equipment Code
2067 (encrypted),
1067 (non-encrypted)
Panel Programming Sensor
Loop
Loop 1
Regulatory Information
We, Nice North America LLC of 5919 Sea Otter Place STE 100, Carlsbad, CA 92010, declare under our sole
responsibility that the device, 2GIG-RPTR100-345 complies with Part 15 of the FCC rules.
FCC & IC Notice
This device complies with Part 15 of the FCC Rules and Industry Canada license exempt standard(s).
Operation is subject to the following two conditions:
(1)
This device may not cause harmful interference, and
(2)
This device must accept any interference received, including interference received that may
cause undesired operation.
©2025 Nice North America LLC. 2GIG is a registered trademark of
Nice North America LLC. All rights reserved.
10034956 Rev-A
Niceforyou.com
Customer Service
760-438-7000
Monday – Friday, 5 a.m. – 4:30 p.m. PST
Saturday, 7 a.m. – 3:30 p.m. PST
www.2gig.com
Nice North America LLC
5919 Sea Otter Place, Suite 100
Carlsbad, CA 92010