Alarm.com ADC-VC730P - Installation Guide

4MP Outdoor PoE Spotlight Camera (ADC-VC730P) - Installation Guide
Pre-Installation Checklist
•
ADC-VC730P camera (included)
•
PoE
switch
•
ADC-V730 AC power adapter (required for non-PoE
connections) (sold separately)
•
An Ethernet / Cat5e cable
•
Router with broadband Internet connection (Cable, DSL, or Fiber Optic) and an open Ethernet port
•
A computer or mobile device with Internet access
•
Username and password for the Alarm.com account to which the camera is added
In the box
Expand all
What's included
ADC-VC730P camera
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
1 Installation sheet with QR code and drill template
Wall anchors & screws (3)
Rubber plug
Important
: A rubber plug has been included with the ADC-VC730P at the base of the mount. This rubber plug should
only be used if the device is being mounted directly over a hole in the wall. The rubber plug will provide a seal to prevent
water from entering the hole in the wall behind the camera. In all other installations, please remove the rubber plug.
Removing the rubber plug will allow you to route the power cable through the mouse hole without bending or breaking
the cable.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
2 Overview
1.
Ambient Light Sensor
2.
Microphone
3.
Spotlight
4.
Status LED
5.
Reset Button
6.
SD Card Slot
7.
SD Card Door
8.
Speaker
Installation
For
information about
general video installation and maintenance guidelines, see
Video Installation Best Practices
.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
3 Enroll the camera to the customer account
Choose the appropriate installation wizard (i.e., technician or customer) below, or proceed to the Ethernet mode section
to begin adding the camera.
Expand all
Service provider technician - MobileTech app installation
1.
Log in to the MobileTech app.
2.
Find the customer account.
3.
Tap
.
4.
Tap
Video
.
5.
Using the
Select Device for Guided Installation Tutorial
dropdown menu, select the desired device.
6.
Tap
Open Installation Tutorial
.
7.
Follow the on-screen instructions.
Customer - Customer app installation wizard
1.
Log in to the Customer app. You will need the username and password of the account to log in.
2.
Tap
.
3.
Tap
Add Device
. If you do not see the Add Device option, use the Ethernet mode instructions below to complete
installation.
4.
Tap
Video Camera
.
5.
Tap
VC730P
.
6.
Follow the on-screen instructions.
Ethernet mode
Note
: Complete these steps prior to installing the camera in its final location.
1.
Feed the Ethernet cable through the cable gland and connect it to the camera's RJ45 port.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
4 2.
Connect the other end of the Ethernet cable to the PoE switch.
3.
Wait 2 minutes for the camera to boot up and connect to the Internet. The LED will be solid green when this
process is complete.
4.
Add the device to the account by either selecting the account in the MobileTech app
or by using a web browser
and entering the following web address:
www.alarm.com/addcamera
.
You will need the customer's username
and password.
For more information about adding a
camera to an account, see
Enroll the video device to the
customer account
.
5.
Select the camera from the video device list or enter its MAC address to begin adding the camera. The camera’s
MAC address is located on the bottom of the device or on the packaging.
6.
Follow the on-screen instructions to finish adding the camera.
You can now power down the camera and install it in its final location using the included hardware.
Physical installation
Verify there are no obstructions near the camera's installation location. Obstructions close to the camera's lens can lead
to poor night vision performance. For information about general installation and maintenance guidelines, see
Video
Installation Best Practices
.
To install the ADC-VC730P in its final location:
Important
: If the ADC-VC730P
will be using an AC power adapter instead of a PoE
switch, the ADC-V730 power
adapter is required.
1.
Use the included drill template to mark the desired location of the holes for the Ethernet/power cable and mounting
screws. Drill a 1/2” hole in the center of the template for the Ethernet/power cable. If mounting to drywall, drill three
9/32” holes and insert the included M5 wall anchors. If mounting to a solid surface (e.g., wood), drill three 1/8” pilot
holes.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
5 2.
Mount the device to a flat surface
(e.g., a wall or ceiling)
8 feet or more above the ground.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
6 To mount the ADC-VC730P when routing the Ethernet/power cable through the wall:
3.
Install the rubber plug over the hole for the Ethernet/power cable.
4.
Connect the device to its power cabling:
▪
If using an Ethernet cable for power, connect the cable
to a PoE
switch. Insert the Ethernet cable
into
the center hole from the mounting template.
▪
If using an AC power adaptor for power, connect the 12 VDC connector to an unplugged 12 VDC
adapter. Insert the power cable into the center hole from the mounting template.
5.
Line up the camera with the three holes created in step 1. Use the included ST4.8 x 32mm self-tapping
screws to fasten the camera to the mounting surface (#10 drywall screws or 3/16" Tapcon screws are also
acceptable).
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
7 To mount the ADC-VC730P when routing the Ethernet/power cable along the wall:
3.
Remove the rubber plug from the power cord.
4.
Connect the device to its power cabling:
▪
If using an Ethernet cable for power, connect the cable
to a
PoE
switch. Insert the Ethernet cable
into
the center hole from the mounting template.
▪
If using an AC power adaptor for power, connect the 12 VDC connector to an unplugged 12 VDC
adapter. Insert the power cable into the center hole from the mounting template.
5.
Line up the camera with the three holes created in step 1. Use the included ST4.8 x 32mm self-tapping
screws to fasten the camera to the mounting surface (#10 drywall screws or 3/16" Tapcon screws are also
acceptable). Route the cable through the cut-out in the mounting plate.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
8 LED reference guide
LED pattern
Description
Off
Power off
Solid green
Connected to Alarm.com
Blinking green
Local network connection
Blinking red
Power on, camera booting
Solid red
No local or internet connection
Blinking yellow
Power cycling (press and hold button for 9-12 seconds)
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
9 LED pattern
Description
Blinking red and green
Reverting to factory default settings (press and hold the
button for 12-15 seconds)
Blinking green and blue
Firmware updating
Troubleshooting
1.
If the camera was previously installed on a different Alarm.com account, it will need to be deleted before it can be
installed again.
2.
If you have issues connecting the camera to the account, power cycle the camera and try again.
Caution
: Prolonged exposure to sunlight in extreme conditions may impact the camera’s performance. The optimal
installation location is in a shaded area such as under an eave.
Regulatory Statements
Operating Temperature: -40°F – 122°F (-40°C – 50°C)
Ingress Protection: IP66
FCC Statements
FCC Short Part 15 Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
FCC Long Part 15 Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
10 guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
•
Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s
authority to operate the equipment.
RF Exposure
This equipment complies with FCC and ISED radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20cm between the equipment and your body.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
Please contact
intsupport@alarm.com
for more information on Canadian RF exposure compliance.
FCC ID
FCC ID: YL6-143V730P
ISED Statements
Condition
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:
1.
This device may not cause interference.
2.
This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil contient des émetteurs/récepteurs sans licence qui sont conformes aux RSS sans licence d'Innovation,
Sciences et Développement économique Canada. L’exploitation est soumise aux deux conditions suivantes :
1.
Cet appareil ne doit pas provoquer d'interférences.
2.
Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un
fonctionnement indésirable de l'appareil.
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
11 RF Exposure
Cet appareil est conforme aux limites d'exposition aux radiofréquences établies par la FCC et l’ISED pour un
environnement non contrôlé. Cet appareil doit être installé et utilisé à une distance minimale de 20 centimètres entre
l’appareil et votre corps. Cet appareil et son ou ses antennes ne doivent pas être situés ou fonctionner en conjonction
avec une autre antenne ou un autre émetteur. Veuillez communiquer avec
intsupport@alarm.com
pour obtenir plus
d’information sur la conformité aux exigences canadiennes en matière d’exposition aux radiofréquences.
IC ID
ID: 9111A-143V730P
https://answers.alarm.com/Partner/Installation_and_Troubleshooting/Video_Devices/4MP_Outdoor_Spotlight_Camera_(ADC-...
Updated: Tue, 24 Mar 2026 21:05:55 GMT
12