First Alert VISTAHTKVRWL - Install Guide (English)- Dated 02/24 Rev. A

VISTAHTKVRWL

Wireless

Converter Communication Module

Installation and Setup Guide

GENERAL INFORMATION

The Takeover Module allows First Alert Pro
VISTA Hybrid
control panels to
communicate with previously installed wireless sensors and modules that
transmit on the following frequencies: 319.5MHz, 345MHz, 433.42 and
433.92MHz. The module connects directly to the control panel and is powered
via the control panel’s connection.

NOTE:

Refer to the VISTAHTKVRWL
Compatibility guide (p/n
R800
-28760
-MC) for the
complete list of compatible
devices.


INSTALLING THE MODULE


Ensure that all electrical
power is removed from the control before installing the
module. Unplug the power
supply and disconnect the backup battery.


1.
Remove electrical power (if applied).

2.
Unplug the power supply.

3.
Disconnect the battery and earth ground.

4.
Set the rotary switch on the
VISTAHTKVRWL

module to the setting associated with the
existing wireless
sensors/modules
and the
Control Panel. See Dial Settings below for the
supported wireless protocols. Only one
wireless protocol can be used in addition to
PROSIX.

5.
Connect the
VISTAHTKVRWL
antenna to the
module before installing the module.

6.
Install the
VISTAHTKVRWL
module on the
edge connector on the right
-hand side of the
PCB. Ensure the receptacle is securely seated
on the edge connector. Route each antenna
as shown.

7.
Secure the module with the provided screw.
8.
Route any wiring through the rear access [8a]
or the knockouts on the bottom right [8b, 8c,
8d] to avoid interfering with the antennas.


Protocol

PRO
HYBRID

5800

5

2GIG

6

DSC

7

ITI/Qolsys

8

Bosch

9

Table 1 –
Rotary Switch Settings


PROGRAMMING

Programming associated with the
VISTAHTKVRWL
module is accomplished as part
of the control panel programming. Refer to the
control panel installation and setup guide for
additional information.



VIS
TAHTKVRWL



SPECIFICATIONS

Board Dimensions
:..................................................................................................................................
2.64
” (67mm)
L x
1.18” (30mm) W x
0. 063
” (1.6
mm)
D
Current Drain
: .......................................................................................................................................................................................................
< 35
mA, standby

Input Voltage:
............................................................................................................................................................
4.2
V – 14V
(provided by the control panel)

Environmental

Operating Temperature:
...............................................................................
-10
°F (
-23°C) to 131°F (55°C) (for compliance agency 32°F (0°C) to 120°F (49°C)
Storage Temperature:
......................................................................................................................................................................
-40°F (
-40°C) to 158°F (70°C)

Humidity:
......................................................................................................
10 to 9
0% relative humidity, non
-condensing (for compliance agency 0% to 85%)



REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE CONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY INFORMATION
AND LIMITATIONS OF THE ENTIRE SYSTEM.



FEDERAL COMMUNICATIONS COMMISSION ISED
STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or U
ser's Manual. Unauthorized
changes or modifications could void the user's authority to operate the equipment.

FCC CLASS B STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following stat
ement for your
information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordanc
e with the manufacturer's
instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing
device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection aga
inst such interference in a
residential installation. However, there is no guarantee that interference will not occur in a particular installation. If th
is equipment does cause
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encou
raged to try to correct the
interference by one or more of the following measures:

• If using an indoor antenna,
replace it with a quality outdoor antenna.

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the radio or television receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch cir
cuits.

• Consult the dealer or an experienced radio/TV technician for help.

ISED
CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES
-003.
Cet appareil numérique de la classe B est conforme à la norme NMB
-003 du Canada.

FCC / I
SED
STATEMENT

This device complies with Part 15 of the FCC Rules, and ISED’s
license
-exempt RSSs
. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference (2) This device must accept any interference received, including interference that may cau
se undesired operation.


Cet appareil est conforme à la partie 15 des r
ègles de la FCC et exempt de licence RSS
d’ISED
. Son fonctionnement est soumis aux conditions suivantes:
(1) Cet appareil ne doit pas causer
d’interférences
nuisibles. (2) Cet appareil doit accepter toute interférence
reçue y compris les interférences
causant
une
réception
indésirable.



RF Exposure Warning

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 inches (20 cm) fr
om all persons and
must not be co
-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi
-
transmitter product procedures.

Mise en Garde

Exposition aux Frequences Radio:
La/les antenne(s) utilisée(s) pour cet émetteur
doit/doivent
être
installée(s)
à une distance de séparation
d'au moins
20 cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou anten
ne,
excepté en conformité avec les procédures de produit multi transmetteur FCC et ISED
s.

Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Dr.,
Melville, NY 11747, Ph: 516
-577
-2000.

The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or auth
orized recyclers. The
correct disposal of end
-of-life equipment will help prevent potential negative consequences for the environment and human health.

Any attempt to reverse
-engineer this device by decoding proprietary protocols, de
-compiling firmware, or any similar actions is strictly prohibited
.



WARRANTY & SUPPORT

For Documentation and Support visit: www.resideo.com.


For Warranty information visit: www.
resideo.com






www.resideo.com

Resideo Technologies, Inc
.
2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

© 2024 Resideo Technologies, Inc. All rights reserved.




ÊR800
-28623A!Š

R
800
-
2
8623A 2/24


Rev.
A