GSMX GSM Communicator Installation Manual

GSMX
GSM Communicator Installation and Setup Guide

REG TX/RX FAUL T SIGN AL

800-04432 9/09 Rev. B

Contents
General Information ........................................................................................... 1 Features.......................................................................................................... 1 Modes of Operation ........................................................................................ 1 Supervision and Fault Detection ................................................................... 2 Specifications.................................................................................................. 2 Data Encryption ............................................................................................. 2 Remote Services Features.............................................................................. 2 Testing the System......................................................................................... 3 Compatibility .................................................................................................. 3 Compliance ..................................................................................................... 3 Mounting and Wiring the Module ...................................................................... 3 Select a Mounting Location ........................................................................... 3 Activating the SIM .................................................................................... 4 Verifying Satisfactory Signal Strength ......................................................... 4 Mounting the Module on the Control Panel.................................................. 5 Mounting the Module on the Wall................................................................. 6 Programming the Module ................................................................................... 8 Using the AlarmNet Direct Website ............................................................. 8 Using the 7720P Programming Tool ............................................................. 9 Programming Conventions ..................................................................... 10 Using the Control Panel............................................................................... 10 Programming for ECP Mode........................................................................ 10 Programming for 4204 and Two-4204 Emulation Modes........................... 11 4204 Emulation Mode Options ............................................................... 11 Programming Options.................................................................................. 13 ECP Status Codes ........................................................................................ 18 Exiting the Programming Mode .................................................................. 19 Setting Factory Defaults.............................................................................. 19 Registering the Module..................................................................................... 20 Registering through the AlarmNet Direct Website .................................... 20 Remote Services....................................................................................... 21 Registering Using the Test Message/Registration Switch ......................... 21 Registering Using the Programming Tool................................................... 21 Replacing an existing module using the programming tool ....................... 22 Registering by Phone ................................................................................... 23 Diagnostic Commands ...................................................................................... 23 Module Identification Displays.................................................................... 23 GSM Status Displays ................................................................................... 24 Central Station Messages................................................................................. 26 Uploading and Downloading of Panel Data..................................................... 27 Glossary ............................................................................................................. 27 LED and Wiring Information ...................................Inside of Back Cover

GSMX Installation and Setup Guide

General Information
The GSMX GSM Communicator (also herein referred to as the module) easily connects to your security system's control panel and sends alarms and messages to AlarmNet for subsequent transfer to the central monitoring station. It can be mounted directly on the control panel or remotely. The GSMX requires an AlarmNet account. For new installations, please obtain the account information from the central station prior to programming this module. The GSMX communicates with AlarmNet using GSM (Global System for Mobile) technology utilizing GPRS (General Packet Radio Service) as a means of data transfer. If the GPRS part of the GSM cellular network is unavailable, it will attempt to send a transmission via SMS (Short Message Service) also known as a text message.

ULC
Features
• • • • • • • •

SMS has not been evaluated for ULC central station communication.

Reports fire, burg, and status messages via GSM. Internal antenna provides additional security. Simple programming using the 7720P programming tool or via the AlarmNet Direct website. Uses 2 way ECP communication with the control. Sends reports in Contact ID format. Supports remote control of alarm system via Remote Services Feature. Allows uploading and downloading of control panel data via GSM. Fully powered (primary and backup battery) from the control panel.

Modes of Operation
• • The GSMX is for control panels that support LRR-ECP communication. The control panel treats the GSMX as a Long Range Radio (LRR) device, so program the control panel accordingly, including setting the module’s LRR device address. 4204 Mode, and two 4204 Mode operation.

•

–1–

GSMX Installation and Setup Guide

Supervision and Fault Detection
• Network communication failure – In the event the AlarmNet network does not hear a supervisory message from the module within a specified time (“Supervision” option, 24 hours, 30 days, or none), AlarmNet notifies the central station of a communication failure. Communication path failure – In the event the module detects a communication path failure, the control panel can be notified of a trouble condition with the module after a specified time has elapsed.

•

Specifications
Dimensions Input Voltage Standby Current Transmit Current Transceiver Type 4 x 7 x 1.75 inches 12VDC (powered via the ECP bus.) 30mA 200mA (Average) GSM/GPRS with internal antenna

Data Encryption
This module supports private key encryption. Private Key encryption means that both the sender and the receiver know the KEY used to encrypt the data. Each device produced by Honeywell is loaded with a unique identifier called a MAC number, and a large random number or KEY. This KEY and MAC number are also stored in the AlarmNet servers. When a device contacts AlarmNet, it sends the MAC number followed by the message that is encrypted using the KEY data. The server looks up the MAC number and uses the KEY associated with it to decrypt the message. The KEY uses 256-bit AES (Rijndael) encryption (which is required for certain government installations). Further, the AlarmNet AES Encryption Software Module Version 1.0 contained in the Honeywell products have NIST approval. Listings for this approval can be found at http://csrc.nist.gov/cryptval/aes/aesval.html Certification number 127.

Remote Services Features

UL

Remote Access and Multi-Mode have not been evaluated by UL.

Honeywell offers secure web based services that enable users to remotely monitor and control their security system. These web services enable users to: –2–

GSMX Installation and Setup Guide • • • Monitor and control their security system from a website Receive e-mail and text message notifications of system events Control the system and receive confirmations using text messages

Dealers can enroll their customers for "Remote Services" by using the AlarmNet Direct website. Once enabled, the specific programming fields associated with these features can be programmed into the communications device either remotely using the AlarmNet Direct website or locally using the 7720P programming tool. E-mail notification (Multi Mode) is intended as a convenience for the user, and does not replace Central Station reporting of critical events (alarms, troubles, etc.).

Testing the System
After installation the security system should be tested. Refer to the control panel installation instructions for procedures to test the entire system.

Compatibility
The GSMX functions with any control panel that utilizes a Honeywell ECP bus and supports Long Range Radio.

Compliance
This device has been tested by ETL to meet the following standards: • UL985 – Residential Fire • UL1023 – Residential Burg

Mounting and Wiring the Module
Select a Mounting Location
When choosing a suitable mounting location, understand that it must be mounted indoors, and for best signal strength it should be mounted vertically. Signal strength is very important for proper operation. For most installations, mounting the unit on the control panel provides adequate signal strength and we suggest that this method is tried first. Especially if the control panel is not in a basement location or in an area that contains large metal objects. If the control panel location does not provide adequate signal strength, then the module can be mounted remotely.

–3–

GSMX Installation and Setup Guide

NOTE: The SIM in the communications module must be ACTIVATED first in order for signal strength to be determined. Once the module is installed and programmed, it must be Registered with AlarmNet. Registering activates the account with AlarmNet and enables the security system's control panel to send reports.

Activating the SIM
Go to: https://services.alarmnet.com/AlarmNetDirect/ If you are not signed up for this service, click on “Dealer Signup” from the login screen to set up your dealer account. You will be instructed how to proceed upon completing the sign-up form. Only one sign-up per dealer is required. Once an initial user is established, additional logins may be created by that user. Log in and follow the on-screen prompts. At this time only activate the SIM so signal strength may be checked. DO NOT register the module at this time. Please have the following information available to activate the SIM: • MAC number and MAC CRC (located on outside of box and on label inside module).

You may log out of the AlarmNet Direct website. Once the module is installed and programmed, it must be Registered with AlarmNet. Registering activates the account with AlarmNet and enables the security system's control panel to send reports.

Verifying Satisfactory Signal Strength
NOTE: In this procedure you will temporarily power up the communications module to check for satisfactory signal strength. You can power it from a 12V battery or from the control panels AUX PWR terminals. In buildings where reception may be a problem, powering from a battery would allow the module to be portable. The following procedure assumes the control panel will be used for power. If satisfactory signal strength is present at the control panel that is the preferred mounting location. 1. Ensure power to the control panel (both AC and battery) is off. Open the enclosure and connect the ECP cable to the GSMX module. Temporarily attach the Black and Red wires to the GND and AUX PWR terminals of the control panel. DO NOT connect the Yellow and Green wires at this time. Turn power on and wait about one minute for the module to initialize. Position the module near a suitable mounting position.

2.

–4–

GSMX Installation and Setup Guide Verify the SIGNAL LED (green) lights steady. This indicates satisfactory signal strength.

Hole Cap SIGNAL LED (green) ON - Satisfactory Signal BLINKING - Marginal Signal OFF - Unsatisfactory Signal

3.

Verify the SIGNAL LED (green) remains steady for a few minutes, then mark that mounting position. Turn power off.

Mounting the Module on the Control Panel
1. 2. 3. Ensure power to the control panel (both AC and battery) is off, then remove the knockout on the top right of the control panel cabinet. Open the GSMX cover. Remove the Hole Cap attached to the plastic (trim as necessary), and snap it into the top opening of the enclosure. Remove the bottom knockout on the GSMX enclosure for the threaded mount. Then install the threaded mount so it snaps into the plastic retaining tabs. Mount the GSMX assembly on the cabinet's knockout, and fasten with the locking nut. Connect the ECP cable to the GSMX circuit board and thread the wires through the threaded mounting adapter.

4.

–5–

GSMX-001-V0

GSMX Installation and Setup Guide

ECP Cable

Control Panel Cabinet

Threaded Mount

To ECP Bus on control panel circuit board.

PANEL DATA IN - Green GND - Black AUX PWR (+12V) - Red PANEL DATA OUT - Yellow

5. 6.

Refer to the installation guide for the control panel, and complete the ECP cable wiring. Secure the wiring with ties as necessary.

Mounting the Module on the Wall
1. Ensure power to the control panel (both AC and battery) is off, then remove a suitable knockout on the top or side of the control panel cabinet. NOTES: • If in the wall wiring will be used, route the wiring through the communications module's rear wiring access hole. • If surface mounted wiring will be used, remove the communications module's bottom knockout and use that to route the wiring. 2. 3. Open the GSMX cover. Remove the Hole Cap attached to the plastic (trim as necessary), and snap it into the top opening of the enclosure. Secure the enclosure to the wall using both mounting holes. –6–

GSMX-005-V0

GSMX Installation and Setup Guide 4. Connect the ECP cable to the GSMX circuit board. When mounting the GSMX off the cabinet, the length of the supplied ECP cable will have to be spliced to a four-wire extender cable. Ensure the splices are located within the GSMX's enclosure. Use the table below to determine the minimum wire gauge for the extender cable.
Minimum Wire Gauge #22 #20 #18 #16 Distance from Control Panel 75 ft (23m) 120 ft (37m) 170 ft (52m) 270 ft (82m)

5.

Route the wires through the rear wiring access hole or bottom knockout on the GSMX. Continue routing the wiring to the control panel. A control panel knockout that is presently used can be utilized, however DO NOT utilize a control panel knockout that is being used for primary power.

Mounting Hole (2) Wiring Access Hole

Hole Cap ECP Cable

To ECP Bus on control panel circuit board.

–7–

GSMX-006-V0

PANEL DATA IN - Green GND - Black AUX PWR (+12V) - Red PANEL DATA OUT - Yellow

GSMX Installation and Setup Guide 6. 7. Refer to the installation guide for the control panel, and complete the ECP cable wiring. Secure the wiring with ties as necessary.

Programming the Module
The GSMX requires an AlarmNet account. For new installations, please obtain the account information from the central station prior to programming this module. You can program the communications module by one of the following methods: • • • Using the AlarmNet Direct website. Using the 7720P Programming Tool. Using the control panel's programming mode (for panels that support this option) to access the communication module's programming.

NOTE: The prompts in this document reflect use of the 7720P Programming Tool.

Using the AlarmNet Direct Website
To program the module via the website (if you are already signed up for this service), go to: https://services.alarmnet.com/AlarmNetDirect/ If you are not signed up for this service, click on “Dealer Sign-Up" and follow the instructions. Log in and follow the on-screen prompts. Please have the following information available when programming the module: • • • • Primary City ID (two-digit number), obtained from your monitoring station. Primary Central Station ID (two-digit number), obtained from your monitoring station. Primary Subscriber ID (four-digit number), obtained from your monitoring station. Communications module MAC ID and MAC CRC number (located on the outside of box and on a label inside the module).

After programming is complete, the module must be registered. Refer to the Register the Module topic.

–8–

GSMX Installation and Setup Guide

Using the 7720P Programming Tool
Ensure the GSMX is powered, and connect the 7720P Programming Tool.

TEST MESSAGE/REGISTRATION Switch
GSMX-007-V0

Each key has two possible functions; a Normal function and a Shift function. • • To perform a Normal key function, simply press the desired key. To perform a Shift function, press the [shift] key, then press the appropriate key.

The following table lists each normal and shift key function.
7720P Normal and Shift Key (shift LED lit) Functions KEY BS/ESC NORMAL KEY FUNCTION [BS]: Press to delete entry SHIFT + KEY FUNCTION [ESC]: Press to quit program mode; also can reset programming defaults.* [↑]: Scroll up programming [Y]: Press for "YES" answer

↓/↑ N/Y SHIFT

[↓]: Scroll down programming [N]: Press for "NO" answer

Press before pressing a SHIFT key function. Will light SHIFT LED. LED goes out once a key is pressed. Press again for each SHIFT function desired. [1]: For entering the number 1 [2]: For entering the number 2 [3]: For entering the number 3 [4]: For entering the number 4 [5]: For entering the number 5 [6]: For entering the number 6 [7]: For entering the number 7 [8]: For entering the number 8 [9]: For entering the number 9 [A]: For entering letter A [B]: For entering letter B [C]: For entering letter C [D]: For entering letter D [E]: For entering letter E [F]: For entering letter F [S]: For entering letter S [T]: For entering letter T [X]: For entering letter X

1/A 2/B 3/C 4/D 5/E 6/F 7/S 8/T 9/X

–9–

GSMX Installation and Setup Guide

SPACE 0 #/ENTE R

[SPACE]: For scrolling option list [0]: For entering the number 0 [#/ENTER]: Starts programming mode; Press to accept entries

No SHIFT function No SHIFT function No SHIFT function

* Active only when the "Exit Programming Mode" prompt is displayed.

Programming Conventions
• Programming is accomplished by answering a series of prompts. Most prompts require only a [Y]es or [N]o response, while others require a numerical response (ID numbers, etc.). The current value is displayed on the second line in parentheses ( ). A "?" indicates an invalid entry. Use the [ENTER] key to accept the current entry and proceed to the next prompt. If the entered value is invalid, pressing [ENTER] redisplays the prompt; the next prompt is not displayed until a valid answer is entered. Use the up/down arrow keys to scroll through the programming prompts without changing any values. Press the [ESC] key to go to the end of the list of prompts.

• •

• •

Using the Control Panel
Some control panels support programming of the communications module through the control panel programming mode. If using this method of programming, only the ECP Mode programming options are available. Other "mode" prompts will not be displayed, and the mode cannot be changed. For a description of key functions on the control panel keypad, and how they map to the 7720P programming tool, refer to the control panel's Programming Guide.

Programming for ECP Mode
ECP mode enables the control panel to communicate with the module via the ECP bus. Control panels that support this bus and have the LRR (Long Range Radio) enabled, send Contact ID format alarms to the module over the ECP bus. Not all control panels support the LRR interface on ECP, so be sure to check the control panel's Installation and Setup Guide to see if it supports this feature.

ULC

Only ECP Mode has been approved for ULC installations.

Press the [ENTER] key to begin programming.

– 10 –

GSMX Installation and Setup Guide

NOTE: The central station can remotely block access to local device programming. If this has been done, prompt on the right appears.

Access to Prog Mode Denied

The default programming values for each prompt are shown in parentheses in the PROMPTS column. Further, the table below shows all the prompts for this programming mode. Depending on your answers, unnecessary prompts will be bypassed and you will advance to the next appropriate prompt.

Programming for 4204 and Two-4204 Emulation Modes
In this mode the communications module emulates a 4204 module (or two) and appears to the control panel as a 4204 module. If two 4204s are enabled in the communications module, it acts as two 4204s using consecutive device addresses. The compatible Honeywell VISTA series or First Alert control panel sends data (triggers) to the communications module as if it were a 4204 module. (The control panel must be configured to recognize one or two 4204 relay modules accordingly.) On VISTA-32FB (or higher) control panels and First Alert equivalents, addresses 6 and 13 should not be used when the secondary 4204 is enabled. Messages are sent in ADEMCO High-Speed format. NOTE: See your control panel Installation and Setup Guide for the number of 4204 modules supported.

4204 Emulation Mode Options
For control panels that do not support LRR-ECP communication, the 4204 Emulation modes provide a means of sending up to eight unique reports based on defined system conditions. In 4204 mode, the communications module functions as a logical 4204 Relay Module, where each relay number, referred to in the module as zone number, can be programmed to send a report based on the output function programmed in the control for that relay. Each relay-zone can also be programmed to send a restore message of the reported condition, can be set to delay transmission of messages, and can be programmed to send reports only when a conditional zone is triggered (armed). In single 4204 mode, the module supports up to four relay-zones. In Two4204 mode, the module functions as two 4204 modules, supporting up to eight relay-zones. Refer to the following table.

– 11 –

GSMX Installation and Setup Guide

4204 Relay Outputs map to zones First 4204 Zones (device address entered in Prompt 15): Relay 1 = Zone 1 Relay 2 = Zone 2 Relay 3 = Zone 3 Relay 4 = Zone 4 or conditional zone trigger if “report only if armed” is selected in any zone 1-3 when using single 4204 mode. NOTE: Zone 4 status is not reported when being used as the conditional (armed) trigger zone. Second 4204 Zones (device address entered in Prompt 15, plus 1): Relay 1 = Zone 5 Relay 2 = Zone 6 Relay 3 = Zone 7 Relay 4 = Zone 8 or conditional zone trigger if “report only if armed” is selected in any zone 1-7 when using Two-4204 mode. NOTE: Zone 8 status is not reported when being used as the conditional (armed) trigger zone or if tamper reporting is enabled.

When using the module in 4204 Emulation Mode, DO NOT enable the LongRange Radio module in control panel programming. Instead, enable 4204 relay module address(es) and program the appropriate relay activation functions for the relay-zones being used. In some control panels, it is called “relay programming” and in others it is called “output device programming.” It is recommended that “close and stay closed” (usually choice 2) action is selected. Selection of momentary activation will cause the communications module to generate an alarm and NOT a restore, even if the module is programmed to send a restore for the given zone. In 4204 mode, messages are reported in ADEMCO High-Speed format. Zone alarms (status 7) are reported with “1” (alarm) or “3” (restore) displayed in the zone position for the respective zone (e.g. alarm on zone 2: 5155 5555 7; restore 5355 5555 7). A supervision fault trouble message is automatically sent if the module detects no activity on its connection to the control. The message is: 5555 5515 5; restore message is: 5555 5535 5.

– 12 –

GSMX Installation and Setup Guide

Programming Options
NOTE: The default programming values are listed in the prompts below.
PROMPTS ENTRY OPTIONS DESCRIPTION

1

Strt Prog Mode? (Y/N)_

[Y], [N]

Enters programming mode.

2

Enter Password

[0-9, A-F, N, S, T, X, Y]

If a password has been previously assigned, this prompt appears. Enter a 4-digit password (0-9, A-F, N, S, T, X, Y). The next prompt appears. To begin programming the module, press [Y] and go to Prompt 9: "Device Mode." To create a password if none has been assigned, press [N] and go to Prompt 4: "Create Password?." To change an existing password, press [N] and go to Prompt 5: "Change Password?." Passwords can be used to protect account and programming information. If no password has been assigned, this prompt appears after pressing [N] at the "Program Device?" prompt. If a password is desired, press [Y] and go to Prompt 6: "Enter Password."

3

Program Device? (Y/N)_

[Y], [N]

4

Create Password? (Y/N)_

[Y], [N]

– 13 –

GSMX Installation and Setup Guide

PROMPTS

ENTRY

OPTIONS

DESCRIPTION

5

Change Password? (Y/N)_

[Y], [N]

If a password has already been assigned, this prompt appears after pressing [N] at the "Program Device?" prompt. Press [Y] if you want to change the password. NOTE: To clear an existing password, without entering a new one, answer [Y] to the "Change Password?" prompt, then press the [Enter] key when prompted for the new password and its confirmation. This prompt is displayed if [Y] was pressed in Prompt 4 or 5. Enter a 4-digit password (0-9, A-F, N, S, T, X, Y). Re-enter the password as confirmation. If the password doesn't match the first entry, the following is displayed followed by the "Exit Prog. Mode?" prompt: Verify Not OK PSWD not created Otherwise, the "Exit Prog. Mode?" prompt is displayed directly.

6

Enter Password

[0-9, A-F, N, S, T, X, Y] [0-9, A-F, N, S, T, X, Y]

7

Verify Password

8

Exit Prog. Mode? (Y/N)_

[Y], [N] [ESC]

Exits program mode. Press [N] to go back to Prompt 3. Press [ESC] to load factory defaults. Refer to the Exiting the Programming Mode topic. Press the [space] key to scroll through the modes of operation. Press [ENTER] to select the desired mode.

9

Device Mode (ECP)_

• ECP • 4204 Emu • Two 4204s

– 14 –

GSMX Installation and Setup Guide

PROMPTS

ENTRY

OPTIONS

DESCRIPTION

NOTE: Prompts 10 and 11 only appear if the Multi-Mode feature has been enabled. Setting up E-mail Notifications (Multi-Mode feature) NOTE: E-mail notification is intended as a convenience for the user, and does not replace Central Station reporting of critical events (alarms, troubles, etc.). Users can receive e-mail notification of system events by using the Multi-Mode feature. The following items must be met to use this feature. • • The Multi-Mode feature must be enabled during account programming on the AlarmNet Direct website by selecting "Enabled" at Multi-Mode prompt. The GSMX will emulate one or two 4204 relay modules to accommodate system events that are programmed in the control panel. When programming the GSMX, at prompt #10, choose 4204-Sourced so the user can be notified of up to four events, or choose 2-4204-Sourced so the user can be notified of up to eight system events. The 4204 relay events used to trigger email notifications are defined on the Honeywell Total Connect website, and must correspond to outputs (relays) programmed in the control panel through Output Device programming. The Multi-Mode address selected at prompt #11 in the GSMX (or at the AlarmNet Direct website) must match the address of a 4204 relay module enabled in the control panel (although you don’t actually connect a module). If using “2-4204-sourced,” the address of the second module is automatically assigned the next device address after the first 4204. Make sure that address is also enabled in the control panel.

•

•

10

Multi Mode (Disabled)_

• Disabled • 4204 Sourced • 2-4204 Sourced

Enable if you want system events sent by e-mail to the user. Select "4204 Sourced" to send up to four events, or "2-4204 Sourced" to send up to eight events. Disable for normal alarm processing and go to Prompt 12 "Primary City ID" prompt. This address must be programmed if using the MultiMode (e-mail notification) feature. The device address must be unique from the normal LRR Device Address and the Keypad Address used for Remote Access or Direct Wire downloading. The address used must also be enabled as a 4204 relay module in Vista and First Alert control panels.

11

Multi Mode Addr (12)

[01-30]

– 15 –

GSMX Installation and Setup Guide

PROMPTS

ENTRY

OPTIONS

DESCRIPTION

NOTE: Account information is provided by the central station administrator.

12

Primary City ID (??)_

[01-99]

Enter the 2-digit primary city ID, 01-99 (decimal).

13

Primary CS ID (??)

[01-FE]

Enter the 2-digit primary central station ID number, 01-FE (HEX).

14

Primary Sub ID (????)

[00019999] [01-30]

Enter the 4-digit subscriber account number, 0001-9999 (decimal). The module communicates with the panel as a Long Range Radio (LRR) device. Enter ECP device address. NOTE: When programming the control, enable the LRR output.

15

Device Address (03)_

Setting up the Remote Access Feature Remote Access enables the user to control the security system using a web browser. This feature must be configured at the AlarmNet Direct website as follows: • Remote Access must be enabled by selecting "Enabled" at the Remote Access prompt. • A keypad address must be enabled in the GSMX in order for the module to communicate with the control panel. • At the “Keypad Type” prompt, select the appropriate Keypad.

16

Remote Access Y/N (N)_

[Y], [N]

Press [Y] to allow the end user to access their system via a website. Availability of this service is controlled by the dealer via the web-based programming tool on the AlarmNet Direct website. NOTE: This prompt will only appear if the Remote Access feature has been enabled. Must be programmed if using the Remote Access feature. Enter the appropriate device address.

17

Keypad Address (28)_

[01-30]

– 16 –

GSMX Installation and Setup Guide

PROMPTS

ENTRY

OPTIONS

DESCRIPTION

18

Supervision (24 Hours)_

• 30 Day • 24 Hour • None

19

Old Alarm Time (10 Minutes)_

20

GSM Flt Time (00 mins)_

• 10 Minutes • 15 Minutes • 30 Minutes • 1 Hour • 2 Hours • 4 Hours • 8 Hours • 12 Hours • 24 Hours [01-99] [00] = not used

The AlarmNet network must hear at least one supervisory message from the module during this supervision period; otherwise, AlarmNet notifies the central station that a communication failure has occurred. (If the supervision period is changed after registration, you must reregister the module.) Press the [space] key to scroll through choices. UL NOTE: Must be 24 hour. The old alarm time sets how long an undeliverable alarm is retried for delivery to the central station. If the message is not validated, it is retried until the old alarm time is reached or the message is validated. Press the [space] key to scroll through choices. UL NOTE: Must be 10 minutes.

In the event the module detects a communication path failure, enter the time delay (in minutes) before the module notifies the control panel with a trouble message. The control panel can then notify the central station. UL NOTE: Must be one (01) minute.

– 17 –

GSMX Installation and Setup Guide

PROMPTS

ENTRY

OPTIONS

DESCRIPTION

21

Review? Y/N

[Y] = review [N] = exit

Reviewing Programming Mode Entries To review the programming options (to ensure that the correct entries have been made), press [Y]. The programming prompts are displayed again. Use the up/down arrow keys to scroll through the program fields without changing any of the values. If a value requires change, simply type in the correct value. When the last field is displayed, the “REVIEW?” prompt again appears. To exit the programming mode, press [N] in response to the "REVIEW?" prompt, and refer to Exiting Programming Mode topic.

ECP Status Codes
The GSMX sends status messages to the control panel to report various failures. Some control panels, (e.g., VISTA-10P, VISTA-15P and VISTA-20P Series) display these status codes on the keypad as “LngRng Radio” followed by a 4-digit code. Commercial panels can supervise the communicator module by way of its ECP address, ex: 03. For example, if the module is disconnected, if it's not registered, or the SIM is deactivated, a "Check 803" will be displayed. The control panel will display a fault message if any of the events listed below occur. • • • • Module lost communications with the control panel. Module lost contact with AlarmNet. Module is not registered; account not activated. Module shutdown.

In addition, the Contact ID codes for some of these conditions are reported by the control panel and sent by AlarmNet to the central station.

– 18 –

GSMX Installation and Setup Guide

Exiting the Programming Mode
To exit the programming mode, press [N] in response to the "REVIEW?" question. Then press [Y] to the "Exit Prog Mode?" question. Upon exiting, the message “Checking Root File TX Path” will be displayed, and the configuration file at the server is updated to log the changes made. When complete, the message "DONE" is displayed to indicate the file was successfully uploaded. If critical configuration changes were made, such as the mode of operation, the GSMX will reset to ensure that the programming features are enabled. If the file is not successfully uploaded, one of the following prompts will be displayed. Follow the steps shown below until the upload is successful. Display Cannot Upload Try Again? Y/N_ Failed to Update Root File! Description GSM Communicator has not yet initialized. Network problem, or you answered "N" to "Cannot Upload Try Again?" prompt. What to do Wait for SIGNAL (green) LED to be lit. Press [Y]. Initiate the Force Server Update command by pressing the [0] key.

Setting Factory Defaults
To reset the programming options to factory-default values, press [ESC] at the "Exit Prog Mode?" prompt. Set Default? Y/N_ Press [Y] to reset factory default values. Press [N] to cancel this function.

If you press [Y], all programmed values are reset to the original factory settings. PLEASE NOTE THAT THIS WILL ERASE ANY PASSWORD THAT MAY HAVE BEEN ENTERED. After pressing [Y], the Create Password prompt appears (see Programming step 4).

– 19 –

GSMX Installation and Setup Guide

Registering the Module
Once you have programmed the GSMX, it must be registered to enable the AlarmNet account. Registering the communications module activates the account with AlarmNet and enables the security system's control panel to send reports. You can register by using one of the following methods: • AlarmNet Direct website • 7720P Programming Tool

• Test Message/Registration switch • Phone The top display LED will indicate the module's registration status as follows: (Refer to the Summary of Connections topic.)
LED REG (green) Indication ON – Module is NOT registered with AlarmNet. OFF – Module is registered with AlarmNet.

You can monitor the registration process by viewing the display LEDs. The TX/RX (yellow) LED and the REG (green) LED will blink slowly in unison while registration is in progress. When the registration successfully completes, the GSMX enters a normal operating mode; the REG (green) LED goes out and the TX/RX (yellow) LED is lit to indicate that the power-on / reset message is waiting to be sent. This message will appear at the receiving station as “E339 803”. The description may read “Trouble – Exp. Mod. Reset”. If registration is not validated within 90 seconds, the GSMX times out, and the REG (green) LED will be lit solid.

Registering through the AlarmNet Direct Website
To register the module via the website, go to: https://services.alarmnet.com/AlarmNetDirect Log in and follow the on-screen prompts. If you are not signed up for this service, click on “Dealer Signup” from the login screen to create an account. You will be instructed how to proceed upon completing the sign-up form. Only one sign-up per dealer is required. Once an initial user is established, additional logins may be created by that user. NOTE: Central Stations can sign up by contacting AlarmNet Support at 800-222-6525 and selecting option 1. Please have the following information available: • • • • Primary City ID (two-digit number). Primary Central Station ID (two-digit hexadecimal number). Primary Subscriber ID (four-digit number). MAC ID and MAC CRC number (located on outside of box and on label inside module). – 20 –

GSMX Installation and Setup Guide After the communications module is registered, you may log out of the AlarmNet Direct website.

Remote Services
The dealer/installer will set up the customer account and define the events to be notified of. These events match the output relay triggering events that were programmed in the control panel. NOTE: At the AlarmNet Direct website, refer to the online "AlarmNet Direct User Guide" for information on configuring the hardware and creating a Total Connect web account for the customer. Once the dealer assigns a login name and password, the customer will receive a “Welcome” e-mail message with their login name along with some helpful information. The customer will receive another e-mail message with their password. They will then be able to receive notifications, and access their system via the Total Connect website or using their cell phone/PDA that supports GSM/GPRS and Text Messaging (SMS).

Registering Using the Test Message/Registration Switch
Initiate the registration sequence by clicking the TEST MESSAGE/REGISTRATION switch three times.

Registering Using the Programming Tool
The interactive registration feature allows the installer to register the GSMX through a series of keyboard commands on the 7720P Programming Tool. This method of registration lets the installer monitor the registration process. Registering … Once the installation is complete, press the [Shift] plus the up arrow [↑] on the 7720P. The registration message is sent and the unit waits for the acknowledgment.

– 21 –

GSMX-009-V0

TEST MESSAGE/ REGISTRATION Switch

GSMX Installation and Setup Guide

Registration SUCCESS

If this is a new installation and the city, central station, and customer numbers have been correctly entered, the GSMX is registered and this message is displayed. The GSMX is now in full service and available for alarm reporting to the central station.

Possible Errors Registration BAD Timed Out Registration BAD Pri Sub ID BAD Registration BAD Pri ID – Need PIN Indicates the city, central station, or customer number for the labeled account(s) is not accepted. The ID information was either entered in error, or the central station failed to pre-authorize programmed ID numbers with AlarmNet customer service. Displayed if this is a repair/replacement, or an error was made in programming the Primary account information of GSMX for an existing account. This prompt appears for 2 seconds. See the Replacing an existing module using the programming tool topic. Displayed if no response to the registration request is received.

Replacing an existing module using the programming tool
Enter PIN# This prompt appears after pressing the down arrow [↓] on the 7720P. Enter a 4-digit alphanumeric PIN number provided by your central station, your dealer or an authorized AlarmNet representative. Press the [ENTER] key. Registering … Registration SUCCESS Registration BAD The registration message is sent and the unit waits for acknowledgement. If the PIN is valid, the new GSMX is registered and the old unit unregistered. Additionally, AlarmNet sends a substitution alarm to the central station. If you entered an invalid PIN, the appropriate message is displayed depending on which account number is being replaced (see above for exact wording). The registration process is repeated. NOTE: Each attempt causes a substitution alarm to be sent to the central station.

– 22 –

GSMX Installation and Setup Guide

Registering by Phone
You can register the module by calling the AlarmNet Support at 1-800-2226525 (Option 1). You will need the following information: • • • MAC ID and CRC (located on outside of box and on label inside module). Subscriber information (provided by the central station), including a city code, CSID, and subscriber ID. When instructed to do so, triple-click the Test Message/Registration switch to complete the registration.

Diagnostic Commands
The 7720P programming tool can be used to view the connectivity settings and options. To invoke diagnostic commands; such as [A], [B], [C], etc., the [shift] key MUST used. For example, [shift] + [A] displays the software revision.

Module Identification Displays
[A] 7845GSM x.x.xx mm/dd/yy MAC xxxxxxxxxxxx MAC CRC yyyy
Software Revision

"x.x.xx" indicates the installed software revision. Mm/dd/yy indicates month, day and year of the revision.
MAC Address “xxxxxxxxxxxx” indicates the GSMX's unique identification number. "yyyy" indicates the MAC CRC number. These numbers are found on the label on the module, as well as the label on the box. Press the [Space] key to go to the next field. Press the [BS] key to go to the previous field. SCID Display

[B]

SCID xxxxx xxxxx xxxxx xxxxx IMEI xxxxxxxx xxxxxx x

Displays the identification number assigned to the SIM card (SCID) in this device. Press the [Space] key to go to the next field. Press the [BS] key to go to the previous field.
IMEI Display

Displays the identification number assigned to the GSM module in this device. Press the [Space] key to get the MAC Address. Press the [BS] key to go to the previous field.

– 23 –

GSMX Installation and Setup Guide

[C]

Mon 01 Jan 2001 05:48:39 am

Time

Retrieves the current date and time from the AlarmNet network in Greenwich Mean Time (GMT). This display confirms that the module is in sync with network.
Encryption Test

[D]

Encryption Test AES Passed!

Performs a self-test of the AES encryption algorithm.
Press the [Space] key to go to the next field. Press the [BS] key to go to the previous field.

GSM Status Displays
[E] PriRSSI GPRS REG -xxxdbm x x
GSM Status Display Screen 1

PriRSSI – Primary Site RSSI level in dBm GPRS – GPRS Service availability where “x” can be: “Y” if GPRS is available “N” if GPRS is Not available REG – Registration status from communicator module where “x” can be: N – Not Registered H – Registered Home S – Searching D – Registration Denied R – Registered Roaming ? – Unknown Registration State Press the [Space] key to go to the next screen. Press the [BS] key to go to the last screen. GSM Status Display Screen 2 Cntry – Country Code Netw – Network Code LAC – Local area code Press the [Space] key to get to the next screen. Press the [BS] key to go to the previous field.

Cntry Netw LAC xxx xxx xxxxx

– 24 –

GSMX Installation and Setup Guide

Cell BaseSt Chan xxxxx x xxx

GSM Status Display Screen 3 Cell – Base Station ID BaseSt – Base Station Antenna Sector Chan – Control Channel in use Press the [Space] key to go to the next screen. Press the [BS] key to go to the previous field. GSM Status Display Screen 4 Secondary GSM Site RSSI level in dbm. Press the [Space] key to go to the GSM Status Display Screen 1. Press the [backspace] key to go to the previous field. ECP Mode Displays the mode of operation and system fault status. Flt – Represents communicator faults: OK = Normal, No fault. G = No network connectivity over GSM and fault time has expired. g = No network connectivity over GSM and fault time has NOT yet expired. Test Alarm Sends a Test alarm to AlarmNet. Functional for a registered GSMX only. If the device is not registered, a message is displayed indicating that the command cannot be executed. Reset the GSMX. Pressing [N] returns to normal mode. Pressing [Y] resets the device. Registration Registers a programmed GSMX with AlarmNet.

Second Site RSSI -xxxdbm

[S]

ECP OK

Flt

[T]

Test Msg Sent

[X]

Reset CPU Y/N Registering …

[Shift] [↑] (UP arrow) [↓] (DN arrow)

Enter PIN#

Registration with PIN for Replacement Module Registers a replacement GSMX with AlarmNet, once programmed, using the existing PIN #.

– 25 –

GSMX Installation and Setup Guide

[0]

Force Server Update? Y/N

Force Upload of Configuration File to Server Pressing [Y] will force the device to upload its entire configuration file to the server. Pressing [N] cancels the operation. NOTE: If the GSM module is not initialized when you enter this command, the following screen will be displayed: Cannot Upload Try Later! _ Wait for the SIGNAL (green) LED to light, indicating the GSM module has completed its initialization, and try again.

[ENTER] Strt Prog Mode? Y/N_

Enter Program Mode Press [Y] to enter program mode; otherwise, press [N].

Central Station Messages
The following messages are sent to the Central Station by AlarmNet for the conditions listed below.
Alarm Condition Power On / Reset (xx=device address) ECP Supervision Communication Path Supervision Test ECP Mode Alarm Code Restore Code E339 C08xx E355 C0000 E350 C0951 5555 5555 9 R355 C0000 R350 C0951 4204 Modes Alarm Code Restore Code 5551 5555 6 5555 5515 5 5555 5551 5 5555 5555 9 5555 5535 5 5555 5553 5

NOTE: The control panel sends its own general code (E353) for a trouble condition.

– 26 –

GSMX Installation and Setup Guide

Uploading and Downloading of Panel Data
NOTE: For UL, downloading may only be performed if a technician is at the site. The GSMX can be used to provide high-speed up/downloading to control panels (that support this feature) over the GPRS network via ECP communication. This allows site maintenance independent of central station monitoring, and modification to sites globally. Refer to the control panel's Installation and Setup Guide for detailed information. • The GSMX cannot be used for Direct-Wire downloading.

Glossary
AES CRC DACT ECP Advanced Encryption Standard Cyclic Redundancy Check used to confirm validity of MAC ID. Digital Automated Communications Terminal Enhanced Console Protocol, is a proprietary bus used in Honeywell control panels to communicate with keypads and peripheral devices. It uses four wires; power, ground, data in, data out. General Packet Radio Service. Global System for Mobile communications, which is an international standard for digital mobile phone systems used for cellular communication. International Mobile Equipment Identity number. Media Access Code, this is a unique address assigned to every network communications device. Typically it is located on the module label, and on the box.

GPRS GSM

IMEI MAC ID

– 27 –

NOTES

LED and Wiring Information
LED REG (green) DESCRIPTION ON – Module is NOT registered with AlarmNet. OFF – Module is registered with AlarmNet. FAST BLINK – Download session with Compass in progress. SLOW BLINK – In unison with yellow LED – Registration in progress. ON – Message transmission pending. QUICK PERIODIC BLINK - Normal FAST BLINK – Message waiting for network ACK. SLOW BLINK – In unison with green LED – Registration in progress. ON – No contact with network. OFF– Normal. SLOW BLINK – Loss of communication with the panel (ECP fault). FAST BLINK – No network contact AND loss of communication with the control panel. ON – Minimum required signal strength is present. BLINKING – Marginal signal strength is present. OFF – Installation is not recommended. FAST BLINK – Hardware Error.

TX/RX (yellow)

FAULT (red)

SIGNAL (green) ALL

TRANSMIT (Blinks during transmisson.)

REG TX/RX FAULT SIGNAL

TEST MESSAGE/REGISTRATION Switch

ECP Cable

To ECP Bus on control panel circuit board.

PANEL DATA IN - Green GND - Black AUX PWR (+12V) - Red PANEL DATA OUT - Yellow

GSMX-010-V0

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. INDUSTRY CANADA (IC) STATEMENTS This device complies with RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

DOCUMENTATION AND ONLINE SUPPORT For the latest documentation and online support information, please go to: http://www.security.honeywell.com/hsc/resources/MyWebTech/ WARRANTY For the latest warranty information, please go to: http://www.security.honeywell.com/hsc/resources/wa/

2 Corporate Center Drive, Suite 100, P.O. Box 9040, Melville, NY 11747 Copyright © 2009 Honeywell International Inc. www.honeywell.com/security

Ê800-04432zŠ
800-04432 9/09 Rev. B