Honeywell GSMVLP Install Guide
2GSM Module with 2-Way Voice Installation and Programming Guide
800-04954V4 7/11 Rev. A
Table of Contents
• • • • • • • • •
Remote Services Features
The Remote Services Features can only be used with Lynx Plus Series/ReadyGuard Plus Series controls Revision 16 or later. Multi Mode (E-mail notification) is intended as a convenience for the user, and does not replace Central Station reporting of critical events (alarms, troubles, etc.).
• • •
The GSMVLP module requires an AlarmNet account. For new installations, please obtain the account information from the central station prior to programming this module. –3–
GSMVLP Module Kit
AUDIO CABLE (PART NO. 600-00170) INCLUDED WITH GSMVLP-KT
NYLON TIE WRAP (2) TIE WRAP MOUNT
Figure 1 – GSMVLP Kit Components
Installing the GSMVLP module
1. Disconnect power from the control, including the battery, BEFORE installing the GSMVLP module. 2. CAUTION: ESD SENSITIVE DEVICE. To discharge any static buildup, briefly touch a chassis ground point before installing this module. Avoid performing this installation while standing on a carpeted floor.
Opening the Lynx Plus or ReadyGuard Plus Series Control and Installing GSMVLP
LYNX PLUS SERIES
FCC ID: CFS8DLLYNXPLUS IC: 573F-LYNXPLUS IC MODEL: LYNXPLUS1 CONTAINS TRANSMITTER MODULE FCC ID: QIPMC55I IC: 7830A-MC55I
800-05190V1 12/09 Rev A
LYNX PLUS SERIES
FCC ID: CFS8DLLYNXPLUS IC: 573F-LYNXPLUS IC MODEL: LYNXPLUS THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS 210 OF INDUSTRY CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. COMPLIES WITH FCC RULES, PART 68 FCC REGISTRATION NO.: 5GBUSA-25623-AL-E RINGER EQUIVALENCE: 0.6B
Figure 2 – FCC/IC Label location
RF Exposure WARNING: The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna(s) or transmitter.
GSMVLP BACK CASE ECP/POWER CABLE
TAPE TIE WRAP MOUNT
WIRE STRAIN RELIEF CLIP
Figure 3 – Installing the GSMVLP Module
Remove the backing from the tape on the provided tie wrap mount. Install the tie wrap mount in the lower right corner of the back case as shown on Figure 3.
Do not block the ventilation slots in the case when installing the tie wrap mount.
For best radio performance, the wires, ECP/power cable, battery and shielded audio cables must be routed as shown in Figure 4.
WIRE ROUTING TUNNELS
BACK CASE 7720P PROGRAMMING JACK TIE WRAP
MOUNTING HOOK TIE WRAP MOUNT
AUDIO CABLE NOTE ENSURE ALL WIRING IS ROUTED THROUGH WIRE STRAIN RELIEF CLIP TIE WRAP
BATTERY CABLE ECP/POWER CABLE
Figure 4 – GSMVLP Wiring Connections and Routing
Programming the GSMVLP Module
Using the AlarmNet Direct website
Using a 7720P Programming Tool
7720 PROGRAMMING TOOL
BS / ESC A B C
N /Y S
MESSAGE STATUS LEDs MINIMUM SIGNAL STRENGTH LED
7720P PROGRAMMING JACK
Figure 5 – 7720P Connection Table 1 – 7720P Normal and Shift Key (shift LED lit) Functions
KEY BS/ESC ↓/↑ N/Y SHIFT 1/A 2/B 3/C 4/D 5/E 6/F 7/S 8/T 9/X SPACE 0 #/ENTER SHIFT KEY FUNCTION [ESC]: Press to quit program mode; also can reset programming defaults* [↓]: Scroll down programming [↑]: Scroll up programming [N]: Press for "NO" answer [Y]: Press SHIFT-Y for "YES" answer Press before pressing a SHIFT key function. Will light SHIFT LED. LED goes out once a key is pressed. Press again for each SHIFT function desired. : For entering the number 1 [A]: For entering letter A : For entering the number 2 [B]: For entering letter B : For entering the number 3 [C]: For entering letter C : For entering the number 4 [D]: For entering letter D : For entering the number 5 [E]: For entering letter E : For entering the number 6 [F]: For entering letter F : For entering the number 7 [S]: For entering letter S : For entering the number 8 [T]: For entering letter T : For entering the number 9 [X]: For entering letter X [SPACE]: For scrolling option list No SHIFT function : For entering the number 0 No SHIFT function [#/ENTER]: Starts programming No SHIFT function mode; Press to accept entries NORMAL KEY FUNCTION [BS]: Press to delete entry
ECP Mode Programming
NOTE: The central station can remotely block access to local device programming. If this has been done, the following prompt appears: Access to Prog Mode Denied
Table 2 – Programming the GSMVLP Module
NOTE: The default programming values are listed in the prompts below.
PROMPTS ENTRY OPTIONS DESCRIPTION
Strt Prog Mode? (Y/N)_ Enter Password
Program Device? (Y/N)_
Create Password? (Y/N)_
Change Password? (Y/N)_
NOTE: To clear an existing password, without entering a new one, answer [Y] to the "Change Password?" prompt, then press the [Enter] key when prompted for the new password and its confirmation.
Verify Not OK PSWD not created
Exit Prog. Mode? (Y/N)_
Device Mode (ECP)_
• • • • •
IMPORTANT NOTE: Do not select any other mode.
E-mail notification is intended as a convenience for the user, and does not replace Central Station reporting of critical events (alarms, troubles, etc.).
PROMPTS 11 Multi Mode (Disabled)_ ENTRY OPTIONS DESCRIPTION
• • • •
Multi Mode Addr (12)
NOTE: This prompt will only appear if the Multi-Mode feature has been enabled.
1. Account information is provided by the central station administrator. 2. The Lynx Plus Series/ReadyGuard Plus Series Controls do not support second account reporting.
13 14 15 16
Primary City ID (??)_ Primary CS ID (??) Primary Sub ID (????) Device Address (03)_
NOTE: When programming the control, enable the LRR output.
– 10 –
PROMPTS ENTRY OPTIONS DESCRIPTION
Remote Access Y/N (N)_
NOTE: This prompt will only appear if the Remote Access feature has been enabled.
Keypad Address (28)_
NOTE: This address must be set to “1”.
Supervision (24 Hours)_
• • •
UL NOTE: Must be 24 hour.
Old Alarm Time (10 Minutes)_
GSM Flt Time (00 mins)_
• • • • • • • • •
UL NOTE: Must be 10 minutes.
UL NOTE: Must be one (01) minute.
– 11 –
ECP Status Codes
• • • •
Exiting Programming Mode
If critical configuration changes were made, such as the mode of operation, the GSMVLP will reset to ensure that the programming features are enabled.
Display Cannot Upload Try Again? Y/N_ Description What to do
Failed to Update Root File!
– 12 –
Setting Factory Defaults
Set Default? Y/N_
IMPORTANT NOTE: THIS WILL ERASE ANY PASSWORD THAT MAY HAVE BEEN ENTERED.
REGISTRATION Registering the GSMVLP
STATUS, GREEN MESSAGE, YELLOW FAULT, RED
Figure 6 – Unregistered GSMVLP Status Display In Normal Operation
Figure 7 – LED Key
The “Registration Success” message is only displayed when the 7720P Programming Tool is used for registration. • • • •
– 13 –
Registering through AlarmNet Direct Website
NOTE: Central Stations sign up by contacting AlarmNet Administration at 800-222-6525 option 3.
Using the Programming Tool
Registering … Registration SUCCESS
Registration BAD Timed Out Registration BAD Pri Sub ID BAD
Registration BAD Pri ID – Need PIN
– 14 –
Replacing an existing module using the programming tool
NOTE: If you are replacing an existing "C Series" radio, you can enter the last four-digits of the "C Series" MIN number.
Registering … Registration SUCCESS Registration BAD
NOTE: Each attempt causes a substitution alarm to be sent to the central station.
Register by Phone
• • •
– 15 –
PROGRAMMER KEYBOARD COMMANDS
[A] 7845GSM x.x.xx mm/dd/yy
Module Identification Displays
[B] MAC xxxxxxxxxxxx MAC CRC yyyy
SCID xxxxx xxxxx xxxxx xxxxx
xxxxxxxx xxxxxx x
Mon 01 Jan 2001 05:48:39 am
Encryption Test AES Passed!
– 16 –
GSMVLP Status Displays
[E] PriRSSI GPRS REG -xxxdbm x x
Cntry Netw LAC xxx xxx xxxxx
Cell BaseSt Chan xxxxx x xxx
Second Site RSSI -xxxdbm
ECP Test Msg Sent
Reset CPU Y/N
[↑] ↑ (UP arrow)
– 17 –
[↓] ↓ (DN arrow) 
Force Server Update? Y/N
NOTE: If the GSMVLP module is not initialized when you enter this command, the following screen will be displayed: Cannot Upload Try Later! _
[ENTER] Strt Prog Mode? Y/N_
– 18 –
APPENDIX A SUMMARY OF LED OPERATION GSMVLP Status Display Operation
• • • •
Figure 8 – LED Key
Minimum Signal Strength LED Operation
Table 3. Status and Signal Strength LED Operation
LED COLOR GREEN LED STATUS DESCRIPTION ON – GSMVLP is NOT registered with AlarmNet. OFF – GSMVLP is registered with AlarmNet. FAST BLINK – Download session with Compass in progress. SLOW BLINK – In unison with yellow LED – Registration in progress. ON – Message transmission pending. QUICK PERIODIC BLINK - Normal FAST BLINK – Message waiting for network ACK. SLOW BLINK – In unison with green LED – Registration in progress. ON – No contact with network. OFF– Normal. SLOW BLINK – Loss of communication with the panel (ECP fault). FAST BLINK – No network contact AND loss of communication with the panel.
MINIMUM SIGNAL STRENGTH
ALL (of the above)
ON – Minimum required signal strength is present. BLINKING – Marginal signal strength is present. OFF– Installation is not recommended. FAST BLINK – Hardware Error. Call the AlarmNet Technical Assistance Center. – 19 –
STATUS, GREEN MESSAGE, YELLOW FAULT, RED STATUS, GREEN MESSAGE, YELLOW FAULT, RED
Figure 9 – A Registered GSMVLP Status Display (A) and an Unregistered GSMVLP Status Display in Normal Operating State (B)
1 STATUS, GREEN MESSAGE, YELLOW FAULT, RED 2 3 4
MAXIMUM SIGNAL STRENGTH, GREEN
Figure 10 – LED Sequence for a Registered GSMVLP Message Transmission
CENTRAL STATION MESSAGES
Table 4 – GSMVLP Central Station Messages
Power On Reset ECP Supervision Communication Path Restore Test
ECP Mode Alarm Code
E339 C0803 E355 C0000 5555 5555 9
ECP Mode Restore Code
R355 C0000 R350 C0951
Note: The control panel sends its own general code (E353) for a trouble condition.
GSMVLP DOWNLOADING General Information
Downloading may only be performed if a technician is at the site. – 20 –
– 21 –
Band Transmit Freq. (MHz) Transmit Power (dBm) Receive Freq. (MHz) Receive Sensitivity (dBm) Number of Channels Channel Spacing (MHz) Duplex Separation (kHz)
GSM 850 GSM 900 GSM 1800 GSM 1900
824-849 890-915 1710-1785 1850-1910
33 33 30 30
869-894 935-960 1805-1880 1930-1990
-107 -107 -106 -105.5
124 124 374 299
200 200 200 200
45 45 95 80
– 22 –
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment. CLASS B DIGITAL DEVICE STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information. This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • If using an indoor antenna, have a quality outdoor antenna installed. • Reorient the receiving antenna until interference is reduced or eliminated. • Move the radio or television receiver away from the receiver/control. • Move the antenna leads away from any wire runs to the receiver/control. • Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. • Consult the dealer or an experienced radio/TV technician for help. ICES-003 Class B Notice - Avis NMB-003, Classe B This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC / IC STATEMENT This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation. Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences causant une reception indésirable.
RF Exposure WARNING: The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 in (20 cm) from all persons and must not be co-located or operating in conjunction with any other antenna(s) or transmitter.
– 23 –
DOCUMENTATION AND ONLINE SUPPORT
For the latest documentation and online support information, please go to: http://www.security.honeywell.com/hsc/resources/MyWebTech/
For the latest warranty information, please go to: http://www.security.honeywell.com/hsc/resources/wa/
2 Corporate Center Drive, Suite 100 P.O. Box 9040, Melville, NY 11747
Copyright © 2011 Honeywell International Inc. www.honeywell.com/security
800-04954V4 7/11 Rev A