Honeywell Home PROSIXCTV Installation Instructions - Dated 01/24 Rev B

PROSiXCTV

Wireless Door/Window Sensor

Installation and Setup Guide

The
PROSiXCTV

is a
two
-
zone

wireless door / window
sensor

with cover and wall tamper. It is

intended for use with
Honeywell
Home
controls that support
PRO
SiX
™
series devices.



MOUNT THE SENSOR

The
sensor
can be
installed
with
two
options:

•
Reed switch
with magnet: Make gap is 0.75"; Break gap is 1.30".

•
Optional
wiring for
external contact
loop:

a) surface wiring

b)
concealed wiring

1. To open the case, f
irmly slide the front
and
back
housings in opposite directions and pull them apart to open the
device.

2. Mount sensor as shown using the double-
sided tape and screws provided.

3. If using an external contact, connect its wires to the terminal block.


NOTE
: Wiring limit is 3ft.

4. Secure the front cover with the #2 x 1/4” screw.

After enrolling
and before mounting, verify adequate signal strength by conducting a sensor test
(see controller’s
instructions) with t
he device in its intended mounting location. Adjust the device location and orientation as necessary.



ENROLL AND SET UP

You must enroll the device in the control. Refer to the
control's programming instruction for detailed procedures.

Set
the
controller
in Programming Mode, when prompted:

1. Pull
the
battery tab
to activate the sensor
. (Use the
magnet if the battery tab is removed.)

2. The LED flashes (
up to about
20 seconds*
) during
enrollment.

•
Both services (Reed and Terminal Block) are
enrolled in sequential (or next available) zone
numbers.

•
The device sends its uniq
ue MAC ID (
Serial
Number)
; the control
ler registers the device and
displays the transmitter data on screen
.
*NOTE
: Enrollment time varies depending on the signal
strength between the device and the controller.

3. When
done,
the LED is ON for 3 seconds and the
control beeps
to confirm
enrollment.

NOTE
: If the device is not successfully enrolled during the
enrollment period, the LED turns off and the device powers
down. Activate a tamper, wired service (loop) or the reed
switch to restart the enrollment process.

4. Program
each zone being used.



•

Reed Switch
Z
one

or Terminal Block Zone



IMPORTANT
: Once enrolled in a system, the
sensor
cannot be
used with another controller until it is removed from the current
controller. See the Controller’s instructions for details.

24
-HOUR ENROLLMENT DELETION AND DEFAULT

If the device is enrolled in a panel different than the intended panel, and you are unable to delete it from the unintended
panel, reset the device to
factory default setting:

1. Open the cover and remove the battery.

2. Hold down the tamper switch while reinserting the battery.
Rapid LED flashing indicates successful deletion (LED
flashes as if in enrollment mode). If LED does not flash, delete was not succes
sful.

3.
Reattach the cover.



This procedure is available for 24 hours after enrollment with a panel and the device remains powered (battery
installed).

LED INDICATIONS


LED

Status



Rapid Flashes for

about 20 seconds, then

ON for 3 seconds

Power Up –
Enrollment


Slow Flash
es
Power Up –
Device enrolled
; Wall
or Cover
Tamper activated. To stop
flashes,
clear the tamper condition
by
reconnecting to the mounting plate
and reattaching the cover
. It also
times out after 10 minutes.


ON

(while in
Programming Mode)

Sensor LED toggles on and off when the sensor is selected. See Sensor
Location Feature.

BATTERY REPLACEMENT
•
Push the bottom latch of the
mounting bracket back to disengage
it. Then
slide the back housing, up
and out to remove
it from the
mounting
bracket
.

•
Slide the front and back housings in
opposite directions
and pull the
housings apart
.
•
Re
move
the battery
,
wait
10
seconds
,
then insert a new battery
.
Recommended batteries:
Duracell DL123A


Resideo
466

Huiderui CR123A


Panasonic CR123A

•
Place the front and back housings
together and slide them together as
shown.

BATTERY CAUTION
: Risk of fire,
explosion and burns.
Do not recharge,
disassemble, heat above 212°
F (100°
C)
or
incinerate. Dispose of used batteries
pro
per
ly. Keep away from children.

NOTE
: Constant exposure to high or low
temperature or high humidity may reduce
battery life.


SPECIFICATIONS:

Battery:
1 x 3V Lithium,
Resideo
466, Panasonic CR123A,

Duracell DL123A
, or Huiderui CR123A

Tamper:
Cover and Wall

RF Frequency
:
2.4GHz

Operating Temperature
: 32°
– 122° F / 0°
– 50° C

(Agency Compliance 32°
– 120° F / 0°
– 49° C)

Relative Humidity:
95% max. (Agency Compliance -
93% max.),

non-
condensing

Dimensions:

1” H x 3.13” L x 1.61” W / 25.5 mm H x 79.5 mm L x 41 mm W


Approval Listings:

FCC / IC

cETLus Listed

Conforms to UL 634

Certified to ULC/ORD
-C634

Other Standards:

RoHS


Product must be tested at

least once each year




FEDERAL COMMUNICATIONS COMMISSION & INDUSTRY CANADA STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to operate the equipment.



CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following stat
ement for your
information: This equipment generates and uses radio frequency energy and if not installed and used properly, that
is, in strict accordance with the
manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to c
omply with the limits for
a Class B computing device in accordance with the specifications in Par
t 15 of FCC Rules, which are designed to provide reasonable protection
against such interference in a residential installation. However, there is no guarantee that interference will not occur in a
particular installation. If this
equipment does cause inter
ference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

•

If using an indoor antenna, replace with a quality outdoor antenna.

•

Reorient the receiving antenna until interference is reduced or eliminated.

•

Move the radio or television receiver away from the receiver/control.

•

Move the antenna leads away from any wire
runs to the receiver/control.

•

Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch cir
cuits.

•

Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES
-003.

Cet appareil numérique de la classe B est conforme à la norme NMB
-003 du Canada.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and Industry Canada’s license
-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, in
cluding interference
that may cause undesired operation.

Cet apparei
l est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement est soumis
aux
conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute int
erférence reçue y compris
les interférences causant une réception indésirable.

RF EXPOSURE

Warning
– The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm)
from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter except in accordance
with FCC and ISED multi
-transmitter product procedures.

Mise en Garde

Exposition aux Fréquences

Radio :
La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de
séparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre
transmetteur ou antenne, excepté en conformité avec les procédures de pr
oduit multi transmetteur FCC et ISED
.

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING
LIMITATIONS OF THE ENTIRE ALARM SYSTEM.


Responsible Party / Issuer of Supplier’s Declaration of
Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center
Drive., Melville, NY 11747, Ph: 516-
577-
2000


The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The
correct disposal of end-
of-life equipment will help prevent potential negative consequences for the environment and human health.

Any attempt to reverse-
engineer this device by decoding proprietary protocols, de-
compiling firmware, or any similar actions is strictly prohibited.


SUPPORT & WARRANTY INFORMATION
For the latest documentation
and
support, please go to:

www.resideo.com


For the latest warranty information, please go to:

www.security.honeywellhome.com/warranty


The Honeywell Home Trademark is used under license from Honeywell International Inc.

This product is manufactured by Resideo
Technologies, Inc.
and its affiliates.


2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747

202
4 Resideo Technologies, Inc.
www.resideo.com


PROSiXCTV


R800-
28560B
01/
24
Rev
B