Honeywell Home PROSIXSIRENO Installation Instructions - Dated 2/19 Rev. B

PROSiXSIRENO

Wireless Outdoor
Audible & Visual Alarm Device

Installation and Setup Gu
ide

This wireless outdoor
alarm device provides
audible and visual notifications
and is intended for use with Honeywell
Home
controls that support
PRO
SiX™
series devic
es
.


PROSiXSIRENO


POWER UP

MOUNTING

The PROSiXSIRENO
can be mounted on the wall or on the
ceiling.

The rear tamper breakout MUST be mounted to a stud, solid
wood, or with a robust wall anchor.

After enrolling, verify adequate signal strength by conduc
ting a sensor
test
(see controller’s instructions) with the device in its intended
mounting location. Adjust the device location and orientation as
necessary.


ENROLL

1.

Set the
c
ontroller

in Programming Mode. Follow the controller’s instructions to be
gin enrollment.

2. Insert four 1.5V AA Lithium batteries (included) to activate the device and
begin the enrollment process.

3. The Green LED flashes rapidly during enrollment (up to about 20 seconds*)
The device sends its unique MAC ID address
(Serial Number) and Services information to the controller.

NOTE
: Enrollment time varies depending on the signal strength between the device and the controller.

4. Enrollment is confirmed when the Green LED is ON for 3 seconds.

5. The device did not enroll in the system if:

•
Th
e s ensor
chirps and the device powers down.

•
The Green LED flashes rapidly when the device is
removed from the mounting bracket (the tamper switch is triggered).

To restart the enrollment process, ensure the system is in programming mode and activate the tamper switch.

NOTE
: Once enrolled in a system, the device cannot be used with another control
ler until it is removed from the current
controller. See the Controller’s instructions for details.


DEFAULT PROSIXSIRENO

If the device is enrolled in a panel
different than the intended panel, and
you are unable to delete it from the
unintended panel, default the device:

1. Open the cover and remove the
batteries.

2. Hold down the tamper switch
while reinserting the batteries.

3.
LED blinks rapidly upon
successful delet
i
on.


This procedure is available for 24 hours after enrollment with a panel and the device
re
mains powered (battery installed).
CHIME OPERATION ENABLED
Refer to the LED and Sounder table for details of chime operation when the CHIME feature is enabled (
factory default
is enabled).


LEDS AND SOUNDER

Refer to the table below for operation of the
four bi
-colored LEDs and an 85dB sounder.


R / W

G / W

Sounder

Status




Green Rapid
Flashes for about
12 seconds, then
ON for 3 seconds

once
Power Up
– E nrollment




3
-
second steady
green, then chirps
and slowly flashes
while tamper is
faulted.

once
Power Up
– Device enrolled



Green ON for 20
seconds


Upon System Disarmed

Red ON for 20
seconds




Upon System Armed

Alternating Red and
White St
robe Flash
2

(continues until the
Alarm is cleared)




Smoke / Heat Alarm




CO Alarm


Wh
ite ON


White ON

1

Burglary Alarm


Red flashes once

every 45 seconds




3

Low Battery




Green Flashes
slowly for 10
minutes


Tamper Activated






Ch
ime operation when the CHIME feature is enabled
x 1

The system is Disarmed
x 2

The system
is Armed, Away mode

x 3

The system is Armed, Stay mode

or a Zone was Faulted


1
Some controls produce a
steady
tone.
Refer to the controls installation i
nstructions.

2
Strobe flash = two flashes per second, then OFF for 1 second.

3
After 7 days
, the sounder chirps once every 45 seconds until the batteries are replaced or die. See the Battery
Replacement section.


TEST THE PROSIXSIRENO

The
PROSiXSIR
EN
O should be tested immediately
after installation and weekly. Activate Test Mode remotely fr
om the
Controller (see Controller’s manual for details).
The produc
t must be tested at least o
nce a year
.

Test Mode tests the sounder and LED
:
•
Sounder
– the B
urglary tone will sound for 3 seconds.

•

LED
– the W
hite LED
strobe will flash for
15 seconds.


BATTERY REPLACEMENT

•

Twist the front cover counterclockwise and separate it from the mounting bracket.

•

Remove the batteries, wait 10 seconds and
insert four new
b atteries

of the same type and brand
.
Recommended replacement batteries:

-
1.5V AA Lithium Bat
teries [Non-
Rechargeable]
-
AA Alkaline batteries can be used, but battery life will be significantly reduced.

NOTE
:
Do not mix old and new batteries, battery ty
pe
s or manufacturers.

•

Reattach the front cover and twist clockwise to secure it in place.

BAT
TERY CAUTION
: Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 212 F (100 C) or
incinerate. Dispose of used batteries properly. Keep awa
y from children.

NOTE
: Constant exposure to high or low temperature or high humidity may red
uce battery life.

SPECIFICATIONS

Range
................................
......................
300 feet nominal indoors (actual range determined by the system in TEST mode)

Battery
................................
.....................
Four 1.5V, AA Lithium, Non-
Rech
argeable; Energizer E
2
, Resideo 462
Tamper
................................
....................
Cover and Wall tamper

RF Frequency
................................
.........
2.4GHz

Input Voltage

................................
..........
3.3VDC

Current
................................
....................
339 mA, Typical

Siren Output Level
................................
. 85 dB at 10 feet

Operating Temperature
.........................
-40° to
50°C /
-40° to 122°F (Agency Compliance 0° to 49°C / 32° to
120
°F)

Relative Humidity
................................
... 95% max. (Agency compliance
– 93% max), non-
condensing
Dimensions
................................
.............
15.5 cm Diameter x 4.7 cm Thick /
6.1 in. Diameter x 1.8 in Thick

RF EXPOSURE
Warning
– The antenna(s) used for this device must be installed to provide a
separation
distance of at least 7.8 inches (20 cm)
from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance
with FCC and ISED multi
-transmitter product procedures.

MISE EN GARDE
:
Ex
position
aux Fréquences Radio:
La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de
séparation d'au moins 20 cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre
transmetteur
ou antenne, excepté en conformité avec les procédures de produit multi transmetteur FCC et ISED.


REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS
REGARDING LIMITATIONS OF THE ENTIRE ALARM SYST
EM.


FED
E
RAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.
Unauthorized changes or modifications could voi
d the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following stat
ement for
your information:

This equi
pment gener
ates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the
manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to c
ompl
y with the l
imits
for a Class B computing device in accordance with the specifications in Par
t 15 of FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that
interferenc
e will not occur in a particular
installation. If this equipment does cause inter
ference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by
one or mor
e of the following measures:

•
If using an indoor antenna, replace it with a qual
ity outdoor antenna.

•
Reorient the receiving antenna until interference is reduced or eliminated.

•
Move the radio or television receiver away from the receiver
/control.

•
Move the antenna leads away from any wire runs to the receiver/control.

•
Plug
the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits
.
•
Consult the dealer or an experienced radio/T
V technician for help.

INDUSTRY CANADA CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES
-003.

Cet appareil numérique de la classe B est conforme à la norme NMB
-003 du Canada.

FCC / IC STATEMENT

This device complies wit
h Part 15 of
the FCC Rules, and Industry Canada’s license-
exempt RSSs. Operation is subject t
o the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including
interference that may
cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de
la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement est soumis
aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2
) Cet appareil doit accepter toute interférence reçue y
compris les interférences causant une réception indésirable.


APPROVAL LISTINGS / APPROB
ATIONS HOMOLOGATIONS

FCC / IC
cETLus Listed
Conforms to UL 985 / UL 1023

Certified to ULC
-
S545 & ULC/ORD
-
C
1023

OTHER STANDARDS

RoHS



























Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Drive.,
Melville, NY 11747, Ph: 516-
577-
2000


The produc
t should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The
correct disposal of end-
of-life equipment will help prevent potential negative consequences for the environment and hum
an health.

Any attempt to reverse-
engineer this device by decoding proprietary protocols, de-
compiling firmware, or any similar actions is strictly prohibited.


SUPPOR
T & WARRANTY INFORMATION
For the latest documentation
and
support, please go to:

www.resideo.com


For the latest warranty information, please go to:

www.security.honeywellhome.com/warranty


The Honeywell Home Trademark is used under license
from Honeywell International Inc.

This product is manufactured
by Resideo
Technologies, Inc.
and its affiliates
.

2 Corporate Center Drive, S
uite 100
P.O. Box 9040, Melville, N
Y 11747

2020
Resideo Technologies, Inc.
www.resideo.com



Ê800
-
25248BrŠ

800-
25248B
2/19 Rev
B