Lutron Caseta P-PKG1W - Quick Install Guide



Related Categories


Document Transcript

Installation for lights with one wall switch (single-pole)
Installing your dimmer
OFF
ON
x3
Some lights have one wall switch, while others
have two or more wall switches (such as stair lights,
which have a switch at both the top and bottom
of the stairs). We’ve included instructions for lights
with one wall switch (called a single-pole). If your
light has more than one switch (called a 3-way),
please visit
www.casetawireless.com/3way

for complete installation instructions and how-to
videos.
WARNING: SHOCK HAZARD.
May result in serious injury or death. Turn off
power at circuit breaker or fuse before installing.
1
Turn power off at circuit breaker!
2
Press and hold “off” button on remote
4
Connect the dimmer
5
Mount the dimmer
6
Attach the wallplate
7
Turn power on at circuit breaker
2
Remove existing switch from wall
Remove the wallplate from switch.
3
Remove side sections (if necessary)
Remove the switch and pull it away from the wall.
*
If your switch has more than 3 wires attached, see
“Installing Caséta
T
Wireless in a 3-way switch application”
video at
www.casetawireless.com/3way
Bend back
and forth.
3
5
1
4
6
Ground
Ground
1
2
3
Ground
7
2
Disconnect all three wires* from the switch.
1
Connect the bare copper (or green) “ground” wire
from the wallbox to the green wire on the dimmer
using a wire connector.
2
Connect either of the remaining wires from the
wallbox to either of the remaining wires on the
dimmer using a second wire connector.
3
Connect the remaining wire from the wall to
the remaining wire on the dimmer using a third
wire connector.
Do not
remove outside side sections
on dimmers at the end of gang.
Each dimmer
has inside side
sections removed.
Dimmer at middle has all
side sections removed.
Attach the adapter to the dimmer using the
screws provided and snap on the wallplate.
‘snap’
(If you installed the dimmer next to other dimmers
or switches, you’ll need to install a wallplate with the
correct size/number of openings to accommodate all
the devices.)
Use the screws provided.
Go to
www.casetawireless.com/support
for
additional troubleshooting suggestions.
For advanced features, tips on how to use Caséta
T
Wireless dimmers with CFLs and LEDs, the complete
Caséta
T
Wireless product line, and more, please visit
www.casetawireless.com/features
Changing the favorite light level
on the Pico
R
remote control
(optional)
You can use the round
“favorite” button on the Pico
R

remote control to recall a
favorite light level. We’ve set
it to 50%, but you can change
it to any level you like.
Favorite
CAUTION
Use only with permanently installed fixtures with
dimmable LED, dimmable CFL, halogen, or
incandescent lamps. To avoid overheating and
possible damage to other equipment, do not use
to control receptacles, motor-driven appliances,
or transformer-supplied appliances.
Codes
Install in accordance with all national and local
electrical codes.
Grounding
When no “grounding means” exist in wallbox, the
National Electrical Code (NEC
®
) allows a control to
be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic
attachment screws or 2) the circuit is protected by a
ground fault circuit interrupter (GFCI). When installing
a control according to these methods, cap or remove
green wire before screwing control into wallbox.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Lutron,
, Claro, and Pico are registered trademarks and FASS, Caséta,
and Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is
a registered trademark of the National Fire Protection Association,
Quincy, Massachusetts. Google and the Google logo are registered
trademarks of Google Inc., used with permission.
© 2014 Lutron Electronics Co., Inc.
P/N 0301716 REV B
3
3
4
4
2
2
1
2
2
2
1
2
2
2
Hold for 6 seconds until LEDs
blink twice. New favorite
level is now saved.
3
Set desired light level on dimmer
4


Press and hold “favorite” button on remote
x2
Important note:
Symptoms
Probable cause and action
Light does
not turn on or
in-wall dimmer
LEDs do not
light up.

Light bulb(s) burned out.

Breaker is OFF or tripped.

Light not properly installed.

Wiring error.


FASS
T
switch on the dimmer
is in the Off position.
Light does
not respond
to Pico
R
remote
control.

The dimmer failed to pair
with Pico
R
remote control;
see Pairing the dimmer and
Pico
R
remote control
.

The dimmer is already at the
light level the Pico
R
remote
control is sending.

The Pico
R
remote control
is outside the 30 ft (9 m)
operating range.

The Pico
R
remote control
battery is low.

The Pico
R
remote control
battery is installed incorrectly.

Bulbs turn off
while being
dimmed.

Bulbs turn on at
high light level
but do not turn
on at a low
light level.

Bulbs flicker
or flash when
dimmed to a low
light level.
Verify bulbs are marked
dimmable and visit
www.casetawireless.com/
lowend

for information on adjusting
the dimmer for best
bulb performance.
Troubleshooting
Hold for 6 seconds
until lights flash 3 times.
5
5
Repeat steps to pair other
Pico
R
remote controls.
Device Ratings
In-wall dimmer
PD-6WCL
120 V
~
50/60 Hz

Pico
R
remote control
PJ2-3BRL
3 V
-
10 mA
(1) CR2032 battery
(included)
quick-start guide
Pico
R
remote control & in-wall dimmer
Welcome
—and thank you for purchasing a Caséta
T

Wireless dimming kit. In order to control your lights from
an app or remote,
you’ll need to replace an existing
switch with a Caséta
T
Wireless in-wall dimmer.
Before you install the dimmer, please watch the
installation video at
www.casetawireless.com/support
We hope you enjoy the convenience of Caséta
T
Wireless!
Contents supplied
Double your warranty
In-wall dimmer
(PD-6WCL)
Claro
R
wallplate
(CW-1)
Tools you’ll need
Flat-head screwdriver
Pico
R
remote control
(PJ2-3BRL)
Wire connectors (3)
Phillips-head screwdriver
Pliers
Screws (2)
Love Caséta
T
Wireless dimmers? Have ideas
for making them better? Tell us what you think
and we’ll extend your warranty by 1 year.
www.casetawireless.com/register
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
P/N 0301716 REV B
Wireless
Hold for 6 seconds
until LEDs start
blinking.
1
Press and hold “off” button on dimmer
Pairing the dimmer and
Pico
R
remote control
The Lutron
R
app will walk you through
setting up your devices.
www.casetawireless.com/LutronApp
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
Important notes:
1. For indoor use only.
2. Operate between 32 ̊F (0 ̊C) and 104 ̊F (40 ̊C).
Replacing light
bulbs using
FASS
T
Pull the FASS
T

switch out on the
in-wall dimmer to
remove power at
the light socket.
On
Off
Darker
Brighter
(with raised icon)
FASS

Front Accessible
Service Switch
Pico
®
remote control
On
Off
Darker
Favorite
Brighter
With a smartphone or tablet
(Bridge required, sold separately)
Lutron
The Caséta
T
Wireless dimmer can be controlled from a smartphone when used
with the
Lutron
R
Smart Bridge
T
.

If you are using the dimmer and
remote control
with the
Lutron
R
Smart Bridge
T

follow the instructions below.
Using your Cas
é
ta
T
Wireless kit
Without a smartphone or tablet
(Bridge not required)
Search for “Lutron Caseta”
Lutron
Lutron
R
Smart Bridge
T
Note:
If you are using the dimmer and remote control with another
manufacturer’s
bridge, please refer to
that
manufacturer’s
instructions
for set-up.
Lutron
Lutron
R
app
3
Add devices

• Pico
R
remotes
• Dimmers
• Shades
Control

three ways
Schedule

your lights
Connect

while away
Apple is a trademark of Apple Inc., registered in the U.S. and other countries. AppStore is a service mark of Apple Inc.
3
Use the Lutron
®
app to complete
ALL
remaining steps
2
Launch the Lutron
®
app
1
Download the Lutron
®
app
Using your controls
Important note:
Removing side sections reduces the dimmer’s
maximum wattage rating. See the chart below
for maximum wattage information.
Maximum* wattage derating chart
(120 V
~
50/60 Hz)
Side sections
removed
None
1 side
2 sides
LED & CFL
150 W
150 W
150 W
or*
Incandescent &
Halogen
600 W
500 W
400 W
* For maximum wattage information when
mixing light bulb types see

www.casetawireless.com/ganging
Works with energy efficient
dimmable light bulbs:
NOTE:
You can mix and match dimmable LED and
CFLs, as well as halogen and incandescent light
bulbs, with Caséta
T
Wireless dimmers.
Dimmable LED and CFL light bulbs vary in their
dimming performance. If you’re using these
bulbs and they flicker or turn off, please visit
www.casetawireless.com/lowend
for information
on adjusting the dimmer for best bulb performance.
For a complete list of compatible dimmable LEDs
and CFLs, please visit
www.casetawireless.com/bulblist
Compatible light bulbs include:
Cree
R

BA19-08027OMF-12DE26-1U100
CR6-575L
Ecosmart
R

ECS BR30 W27 FL 120
ECS 20 WW FL 50WE 120
Feit
R

A19/OM/LED
Philips
R

9290002295
Sylvania
R

LED12A19/DIM/O/827
LED21PAR38/DIM/P/930/FL30
CFL
—up to 150 W
LED
—up to 150 W
Halogen
—up to 600 W
Incandescent
—up to 600 W Cómo instalar el atenuador
Algunas luces tienen un interruptor de pared,
mientras que otras tienen dos o más interruptores
de pared (como luces de escaleras, que tienen
un interruptor tanto al inicio como al final de
las escaleras). Hemos incluido instrucciones
para luces con un interruptor de pared (llamado
unipolar). Si su luz tiene más de un interruptor
(llamado de 3 vías), visite:
www.casetawireless.com/3way
para obtener
las instrucciones completas de instalación y los
videos instructivos.
Nota importante:
Instalación de luces con un interruptor de pared (unipolar)
x3
1
Corte la corriente del cortacircuitos
4
Conecte el atenuador
5


Coloque el atenuador
6
Coloque la placa de pared
2
Retire el interruptor actual de la pared
Retire la placa de pared del interruptor.
Retire el interruptor y aléjelo de la pared.
*
Si su interruptor tiene más de 3 cables, consulte el
video “Installing Caséta
T
Wireless in a 3-way switch
application” (Cómo instalar Caséta
T
Wireless en una
aplicación de interruptor de 3 vía) a:
www.casetawireless.com/3way
3
5
1
4
6
Tierra
Tierra
1
2
3
7
2
Desconecte los tres cables* del interruptor.
Conecte el adaptador al atenuador con los tornillos
suministrados y encájelo en la placa de pared.
“chasquido”
Use los tornillos proporcionados.
Para ver características avanzadas, consejos para
usar los atenuadores Caséta
T
Wireless con luces LFCA
y LED, la línea completa de productos Caséta
T
Wireless
y más, visite
www.casetawireless.com/features
Cómo cambiar el nivel de luz
favorito en el control remoto
Pico
R

(opcional)
Lutron,
, Claro, y Pico son marcas registradas y FASS, Caséta y
Smart Bridge son marcas comerciales de Lutron Electronics Co. Inc.
NEC es una marca registrada de National Fire Protection Association,
Quincy, Massachusetts. Google y el logotipo de Google son marcas
registradas de Google, Inc., utilizadas con autorización.
© 2014 Lutron Electronics Co., Inc.
P/N 0301716 REV B
3
3
4
4
2
2
1
2
2
2
1
2
2
2
Presione durante 6 segundos
hasta que las luces LED
parpadeen dos veces.
El nuevo nivel favorito
ha sido guardado.
x2
5
5
guía de inicio rápido
Control remoto Pico
R
&
atenuador empotrable

Lea antes de instalar.
Bienvenido
, y gracias por comprar el kit de atenuador
Caséta
T
Wireless. Para controlar sus luces desde una
aplicación o un control remoto, deberá reemplazar
un interruptor existente por un atenuador empotrado
Caséta
T
Wireless.
Antes de instalar el atenuador, vea el video de
instalación en
www.casetawireless.com/support
¡Esperamos que disfrute la comodidad de
Caséta
T
Wireless!
NOTA:
Puede combinar focos LFCA y LED
atenuables, así como focos de luz halógenos
e incandescentes, con los atenuadores
Caséta
T
Wireless.
Los focos de luz atenuables LFCA y LED
varían en su rendimiento de atenuación. Si está
utilizando estos focos y parpadean o se apagan,
visite
www.casetawireless.com/lowend

para obtener información sobre cómo ajustar el
atenuador para un mejor rendimiento del foco.
Para obtener una lista completa de los
LFCA y LED atenuables compatibles, visite
www.casetawireless.com/bulblist
Los focos de luz compatibles incluyen:
Cree
R

BA19-08027OMF-12DE26-1U100
CR6-575L
Ecosmart
R

ECS BR30 W27 FL 120
ECS 20 WW FL 50WE 120
Feit
R

A19/OM/LED
Philips
R

9290002295
Sylvania
R

LED12A19/DIM/O/827
LED21PAR38/DIM/P/930/FL30
Contenido suministrado
Doble su garantía
Atenuador
empotrable
(PD-6WCL)
Placa de pared
Claro
®
(CW-1)
Herramientas que necesitará
Destornillador de cabeza plana
Control remoto Pico
®
(PJ2-3BRL)
Conectores de cables (3)
Destornillador Phillips
Alicates
Tornillos (2)
¿Le encantan los atenuadores Caséta
T
Wireless?
¿Tiene alguna idea para mejorarlos? Cuéntenos su
opinión y extenderemos la garantía por 1 año.
www.casetawireless.com/register
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299,
E.U.A.
P/N 0301716 REV B
Wireless
Cómo emparejar el atenuador
con el control remoto Pico
R

La aplicación Lutron
R
lo guiará por la
configuración de sus dispositivos.
www.casetawireless.com/LutronApp
Con un teléfono inteligente o una tableta
(se requiere un dispositivo de conexión que se vende por separado)
Lutron
El atenuador Caséta
T
Wireless se puede controlar con un teléfono inteligente
cuando se utiliza con el Lutron
R
Smart Bridge
T
.

Si utiliza el atenuador y el control remoto con el Lutron
R
Smart Bridge
T
,
siga las instrucciones a continuación.
Uso del kit Cas
é
ta
T
Wireless
Sin un teléfono inteligente o una tableta
(no se requiere un dispositivo de conexión)
Busque “Lutron Caseta”
Lutron
Lutron
R
Smart Bridge
T
Nota: Si utiliza el atenuador y el control remoto con el
dispositivo de conexión de otro fabricante, consulte las
instrucciones del fabricante para configurarlo
Lutron
Aplicación
Lutron
R
3
ADVERTENCIA: RIESGO DE
DESCARGA ELÉCTRICA
Puede resultar en lesiones graves o la muerte.
Corte la corriente del cortacircuitos o fusible
antes de instalar.
APAGADO
Nota importante:
Cuando retira las secciones laterales, se reduce
el vataje de régimen máximo. Consulte el cuadro
a continuación para obtener la información de
vataje máximo.
* Para obtener información del vataje máximo al
combinar tipos de focos de luz, consulte

www.casetawireless.com/ganging
Cuadro de reducción de vataje máximo*
(120 V
~
50/60 Hz)
Secciones
laterales quitadas
Ninguna 1 lateral
2 laterales
LED y LFCA
150 W
150 W
150 W
o
*
Incandescente
y halógena
600 W
500 W
400 W
Cada atenuador tiene
las secciones laterales
internas quitadas.
El atenuador del medio
tiene todas las secciones
laterales quitadas.
Doble hacia atrás
y hacia delante.
No
quite las secciones laterales externas
de los atenuadores al final de la conexión.
3

Retire las secciones laterales
(en caso de ser necesario)
Tierra
1
Conecte el cable a tierra de cobre sin protección
(o verde) desde la caja de pared al cable verde del
atenuador utilizando un conector de cable.
2
Conecte uno de los cables restantes de la caja de
pared a uno de los cables restantes del atenuador
utilizando un segundo conector de cable.
3
Conecte el otro cable de la caja de pared al cable
restante del atenuador utilizando un tercer conector
de cable.
(Si instaló el atenuador al lado de otros atenuadores
o interruptores, debe instalar una placa de pared que
tenga la cantidad correcta de orificios y del tamaño
correcto para instalar todos los dispositivos.)
7

Encienda la corriente
del cortacircuitos
ENCENDIDO
PRECAUCIÓN
Use solo con luminarias permanentes con lámparas
LED atenuables, LFCA atenuables, halógenas o
incandescentes. Para evitar el sobrecalentamiento
y posibles daños a otros equipos, no lo use para
controlar receptáculos, electrodomésticos con motor
o electrodomésticos con transformador.
Códigos
Instale de acuerdo con todos los códigos eléctricos
nacionales y locales.
Conexión a tierra
Cuando no exista ningún medio de conexión a
tierra en la caja de pared, el NEC
®
(Código Eléctrico
Nacional) permite la instalación de un control como
reemplazo si 1) se usa una placa frontal incombustible
que no sea metálica con tornillos de sujeción no
metálicos o 2) el circuito está protegido por un GFCI
(interruptor de circuito por falla a tierra). Al instalar un
control de acuerdo con estos métodos, tape o retire
el cable verde antes de atornillar el control a la caja de
pared.
Información de la FCC/IC
Este dispositivo cumple con la parte 15 de las reglas de la FFC (Comisión
Federal de Comunicaciones) y con las normas RSS de IC (Industry Canada)
para dispositivos exentos de licencia. La operación está sujeta a las dos
condiciones siguientes: (1) Este dispositivo no debe causar interferencia
perjudicial y (2) este dispositivo debe aceptar cualquier interferencia recibida,
incluyendo las que pueden causar una operación indeseada. Cualquier cambio
o modificación sin la aprobación explícita de Lutron Electronics Co., Inc. puede
anular la autorización del usuario para operar el equipo.
Nota: Este equipo ha sido probado y se comprobó que cumple con los límites
para dispositivos digitales de Clase B, de acuerdo con la Parte 15 de las
Reglas de la FCC. Estos límites se han diseñado para proveer una protección
razonable contra interferencias dañinas en una instalación residencial. Este
equipo genera, usa y puede emitir energía de radiofrecuencia y si no se instala
y utiliza de acuerdo con las instrucciones, puede causar interferencia dañina en
las comunicaciones de radio. Sin embargo, no hay garantía de que no ocurrirá
interferencia en una instalación determinada. Si este equipo causa interferencia
dañina en la recepción de la radio o la televisión, que se puede determinar
encendiendo y apagando el equipo, el usuario puede tratar de corregir la
interferencia mediante uno o más de los siguientes procedimientos:
—Cambiar la orientación o ubicación de la antena receptora.
—Aumentar la separación entre el equipo y el receptor.

Conectar el equipo a un receptáculo que esté en un circuito diferente al del
receptor.

Consultar al distribuidor o a un técnico experimentado en radio/TV para
obtener ayuda.
Garantía
Para obtener información sobre la garantía, visite
www.casetawireless.com/warranty
Apple es una marca registrada de Apple Inc. en E.U.A. y en otros países. App Store es una marca de servicio de Apple Inc.
Ingrese a
www.casetawireless.com/support
para
obtener sugerencias adicionales para la resolución
de problemas.
Síntomas
Causa probable y acción
La luz no se
enciende o no
se encienden los
LED del atenuador
empotrable.

Los foco(s) están quemados.

El cortacircuitos está apagado
o se disparó.

La luz no está instalada
correctamente.

Error de cableado.


El interruptor FASS
T
del
atenuador está apagado.
La luz no responde
al control remoto
Pico
R
.

Falló el emparejamiento del
atenuador con el control
remoto Pico
R
;
consulte Cómo
emparejar el atenuador con el
control remoto Pico
R
.

El atenuador ya se encuentra
en el nivel de luz solicitado por
el control remoto Pico
R
.

El control remoto Pico
R

está fuera del rango
de funcionamiento
de 9 m (30 pies).

La batería del control remoto
Pico
R
están bajas.

La batería del control remoto
Pico
R
están mal instaladas.

Los focos se
apagan mientras
se atenúan.

Los focos se
encienden en
un nivel de luz
alto pero no se
encienden en un
nivel de luz bajo.

Los focos
parpadean
cuando se
atenúan a un
nivel de luz bajo.
Verifique que los focos tengan la
marca de atenuable y visite
www.casetawireless.
com/lowend
para obtener
información sobre cómo ajustar
el atenuador para un mejor
rendimiento del foco.
Resolución de problemas
Encendido
Apagado
Más oscuro
Más brillante
(con icono en relieve)
Interruptor
de servicio
accesible desde
el frente FASS

Cómo reemplazar los focos de luz usando FASS
T
Deslice el interruptor FASS
T
hacia fuera en el atenuador
empotrable para desconectar la energía en el zócalo
de la luz.
Más brillante

Encendido
Apagado
Más oscuro
Control remoto Pico
®
Favorito
Notas importantes:
1. Solo para uso en interiores.
2. Opere entre 0 °C (32 °F) y 40 °C (104 °F).
Atenuador empotrable
PD-6WCL
120 V
~
50/60 Hz
Control remoto Pico
R

PJ2-3BRL
3 V
-
10 mA
(1) Batería CR2032 (incluida)
Clasificación de los dispositivos
4


Mantenga presionado el botón
“favorito” del control remoto
3

Configure el nivel de luz deseado
en el atenuador
Favorito
Puede usar el botón redondo
“favorito” en el control remoto
Pico
R
para recuperar un nivel de
luz favorito. Lo hemos establecido
en 50%, pero puede cambiarlo al
nivel que desee.
1

Mantenga presionado el botón
“apagado” del atenuador
Presione durante
6 segundos hasta
que las luces LED
comiencen
a parpadear.
2

Mantenga presionado el botón
“apagado” del control remoto
Mantenga presionado
durante 6 segundos
hasta que la luz
parpadee 3 veces.
Repita los pasos para emparejar
otros controles remotos Pico
R
.
3
Utilice la aplicación de Lutron
®
para completar
TODOS
los pasos restantes
2
Inicie la aplicación Lutron
®

1
Descargue la aplicación Lutron
®

Cómo usar sus controles
Añada dispositivos


Controles
remotos Pico
R

• Atenuadores
• Persianas
Controle
de tres 
maneras
Programe

sus luces
Conecte

a larga
distancia
LED
—hasta 150 W
LFCA
—hasta 150 W
Funciona con focos de luz
atenuable de bajo consumo
energético:
Incandescente
—hasta 600 W
Halógeno
—hasta 600 W


Uploaded