Honeywell Home PROSIXPIR Installation Instructions - Dated 2/19 Rev. B

PROSiXPIR

Wireless Passive Infrared Motion Sensor

Installation Instructions



Th
is wireless passive infrared motion sensor is
intended for use with Honeywell
Home
controls that support PRO
SiX
™
series devices.

Mounting Location

•
The optimal range is
obtained at a mounting
height of 7’ 6” (2.3 m).
•
Allow a clear line
-of-sight to
all areas to protect.

•
Do not directly face
windows.

•
Avoid close proximity to
moving machinery,
fluorescent lights, and
heating/cooling sources.

•

For use in applications with
pets up to 80 pounds (36
kilograms).



In Applications with Animals
:


•

Mount with t
he center of the device at 7.5 feet (2.3m)

•

Mount where pet cannot come within 6 feet (1.8m) of the sensor by climbing on furniture,
stairs, boxes or other objects.

•

Test each installation to determine exact level of animal immunity; levels vary based on
env
ironmental differences and the amount of heat radiated by an animal.

Mounting Options

After enrolling, verify adequate
signal strength by conducting a
sensor test
(see the
controller’s instructions) with
the device in its intended
mounting location. Adjust the
device location and orientation
as necessary
.

The
PROSIXPIR
can be
mounted on the wall or in
corners:

•
[A]
= Wall mounting holes.

•
[B]
= Corner mounting
holes.

• The rear tamper plate
MUST be mounted to a
stud, solid wood, or with a
robust wall anchor.




2

Enroll the
PROSIXPIR


Press down on the top latch and separate the
front and back covers
.
1. Pu
t the
control
in Programming Mode:

2. Remove the battery tab to activate and begin
the enrollment process.

3. The
green
LED
beneath the battery
flashes
(up to about
20 seconds*)
during enrollment
.
The device sends its unique MAC ID (Serial
Number) and Services information to the
controller.

*NOTE
: Enrollment time varies depending on the
signal strength between the device and the
controller.

4. Enrollment is confirmed wh
en the LED is ON
for 3 seconds.

NOTE
: If the sensor is not successfully enrolled
during the enrollment period, the LED turns off and
the device enters a sleep mode.
Activate a tamper
or remove and reinsert the battery to restart the
enrollment process.

NOT
E
: Pet Immunity is selectable: Off or Up to

80 lbs (36 kg).

NOTE
: Once enrolled in a system, the sensor
cannot be used with another controller until it is
removed from the current controller. See the
Controller’s instructions for details.



24
-Hour
Enrollment
Deletion and Default

If the device is enrolled in a panel different than the intended
panel, and you are unable to delete it from the unintended
panel,
reset
default
the device
to factory default setting:

1. Open the cover and remove the battery.

2. Hold
down the tamper switch while reinserting the battery.

This procedure is available for 24 hours after enrollment with a
panel and the device remains powered (battery installed).


Walk Test the
PROSIXPIR

After power up and enrollment, the sensor
automatically enters Walk Test mode.

Walk through the detection area and observe the
LED.

After 10 minutes, the sensor automatically exits
Test mode, disables the LED and enters normal
operation mode.

To restart a 10 minute Test period,
activate the
Test mode with t
he controller (see the Controller’s
instructions)
, or use the flashlight feature
(see the
following section)
.
NOTE
: the system must be
disarmed
to enter Test
Mode.


3

Flashlight Feature

The flashlight feature is only available for the first 24 hours after the
first power up, or until the system is first armed.
This feature is no
longer available after the first system arming
.
Each time the flashlight features is used, and the system is disarmed,
the walk test timer restarts for 10 minutes.

1. Use a flashlight with a bright light beam, and stand within 4’ (1.2 m)

of the sensor.

2. Swing the light beam past the sensor
Lens
3-5 times, holding the
beam on the window for 0.5 second each pass.



Detection Patterns


Battery
Replacement


•
Press the latch at the
top of the device
and slide
the front cover down to r
emove
it.
•
Remove the battery and wait 10 seconds, then
insert a new
battery.
R
ecommended batteries:
Panasonic CR123A

Huiderui CR
123
A
Duracell DL123A

•
Place the front and back covers
together and slide
the
front cover upward
as shown.

BATTERY CAUTION:
Risk of fire, explosion and burns. Do not
recharge, disassemble, heat above 212°F (100°C) or incinerate.
Dispose of used batteries properly. Keep away from children.

NOTE
: Constant exposure to high or low temperature or high
humidity may reduce battery life.


Specifications

Range:
40’ x 56’ / 12 m x 17 m


Wall Mounting Height:
7’
– 9’ (2.1 m –
2.7 m); Optimal 7’6” (2.3 m)

Battery
: 1 x 3V, Lithium; Panasonic CR123A, Duracell DL 123A,

Huiderui CR123A

RF Frequency
: 2.4GHz

Tamper
: Cover and Wall
– reported separately to panel.

Operating Temperature
: 32°
– 122°F / 0°
– 50°C (Agency Compliance 32° –


120°F / 0°
– 49°C)

Relative Humidity
: 95%
max. (Agency Compliance -
93% max.)
,
non
-condensi
ng

Dimensions
:
4.13” H x 2.38” W x 1.61” D / 105 mm H x 60.4 mm W x 41 mm D

Weight:
3.97

oz / 112.67
g (net weight)

Approval Listings

FCC / IC

cETL
us Listed

Conforms
to UL
639

Certifi
ed to ULC
-S306
-03

Other Standards:

SIA-PIR
-01

RoHS



The product must be tested at least
once each year
.

Zones

A

18
Lower

B

46
Intermediate

C

36
Long



NOTE
: the flashlight feature only
initiates or
restarts the
Test
Mode and does not change any other sensor settings.



FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or U
ser's Manual.
Unauthorized changes or modifications could void the user's authority to operate the equipment.

CLASS B DIGITAL DEVICE STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following stat
eme
nt for
your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordanc
e with the
manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the
limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to pr
ovide
reasonable protection against such interference in a residential installation. H
owever, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

• If using an indoor antenna, replace it with a quality outdoor antenna.

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the radio or televisi
on receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch cir
cuits.

• Consult the dealer or an experienced radio/TV technician for help.

INDUSTRY CANADA CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES
-003.

Cet appareil numérique de la classe B est conforme à la norme NMB
-003 du Canada.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and Industry Canada’s license-
exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement
est
soumis aux conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute
interférence reçue y compris les interférences causant une réception indésirable.


Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary
of Resideo Technologies, Inc., 2 Corporate
Center Drive., Melville, NY 11747, Ph: 516-
577-
2000

RF
EXPOSURE

Warning
– The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm) from al
l persons
and must not be co-
located or operating in conjunction with any other antenna or transmitter except in accordance with FCC
and ISED
multi
-
transmitter product procedures.

Mise en Garde

Exposition aux Fréquences
Radio :
La/les antenne(s) utilisée(s) pour cet é
metteur doit/doivent être installée(s) à une distance de séparation d'au
moins 20 cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou
antenne, excepté en
conformité avec les procédures de produit multi transmetteur FCC et ISED.



The product should not be disposed of with other

household waste. Check for the nearest authorized collection centers
or authorized recyclers. The correct disposal of end-
of-life equipment will help prevent potential negative consequences
for the environment and human health.

Any attempt to reverse-
engi
neer this device by decoding proprietary protocols, de-
compiling firmware, or any similar
actions is strictly prohibited.

Support and Warranty

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL WITH WHICH THIS DEVICE IS USED, FOR DETAILS REGARDING
LIMITATIONS OF THE ENTIRE ALARM SYSTEM.

For the latest documentat
ion and online support information, please go to:

https://mywebtech.honeywe
llhome.com



For the latest warranty information, please go to:
www.security.honeywellhome.com/warranty

For patent information, see
www.resideo.com

The Honeywell Home Trademark is
used under license from Honeywell International Inc.

This product is manufactured by Resideo and its affiliates
.

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747


20
20
Resideo Technologies, Inc.

www.resideo.com



Ê800
-
25243BEŠ

800
-
25243
B



2/19



Rev
B