Honeywell IPCAM-WIC1 - Quick Install Guide

800-23361
6/17 Rev. A
Google Play and the Google Play logo are trademarks of Google Inc.



IPCAM
-WIC1
HD Wi
-Fi Indoor Video Camera

Quick Installation Guide

IPCAM
-WIC1 is a
n HD
Wi
-Fi video camera intended for indoor use with Honeywell Total Connect
® 2.0
.
Low
-light
operation

is indicated by two small red
LEDs located on the front of the camera below the lens.

Camera setup

requires a

Total Connect® 2.0

account
and
the
new
Total Connect 2.0
mobile
app.

Video Services

must
be enabled in AlarmNet 360
™
.
Camera operation requires minimum available bandwidth of 1.5Mbps.



For best results, set up only one camera at a time.
Download the Total Connect® 2.0 app from
the App Store or on
Google Play.

(Look for the
red
Total Connect
logo
.)



a.

Turn on your
smart device’s Bluetooth and Wi
-Fi.

b.

Launch the app and sign in with your Total Connect® 2.0
account.

c.

Remove
the camera’s magnetic base; plug in the power
connector.

d.

Replace the base but don’t connect the camera to AC power yet.




a.

Press

Cameras
at the bottom of the app
and then
ADD CAMERA
.
b.

Select the type
of camera you’re installing
.
c.

Name
the
camera
and
press

NEXT
.
The camera remains in
setup mode
for about 10 minutes.




a.

Plug
in the
power supply
. After about a minute, the camera
sounds a tone.

b.

When the camera’s
LED
starts
flashing blue,
press

NEXT
on the app.

c.

The
app
displays
Pair Your Camera
and a

QR code
appears
. (This
can take up to 90 seconds
.)
d.

Show the QR code to the camera from 3
– 7 inches
away.
When
the code has been scanned, the camera sounds a tone.

e.

When the
app verifies the QR code
, choose your system
’s Wi
-Fi
network and touch
NEXT
.
f.

Enter the network password and press

NEXT
.
g.

When camera registration is complete, the process is
complete
*.
Press
DONE
or
ADD ANOTHER CAMERA
.




After setup, go back to the
Video
tab and check your newly
-
registered camera. Touch the
thumbnail

image
to launch a live
stream from the camera.





*The app will tell you if you need to repeat the setup process.
This involves resetting the camera. See the other side of this
sheet for more information on using the
Reset
switch

Resetting the Camera

If Wi
-Fi fails, or to
connect
the camera to a different
network, use a paper clip to activate the Reset switch
.
•

To reset the connection,
press
and hold for 1
5 seconds

•

To join a new/different network
:
o

On the app’s
Video
screen, press
and delete the camera in
Camera Settings

o

Press and hold the
Reset
switch
for 15
seconds to reset all set
tings to their factory defaults

o

Unplug the camera and then reconnect it.

o

Repeat the registration procedure.


LED STATUS INDICATOR

During installation


Blue, blinking

Power on. Ready to start setup.


Blue, steady

Connected to the app. Ready to complete setup.


Purple, steady

QR code scan is complete. Restart the Wi
-
Fi connection process.


Green, blinking

Connecting to Wi
-
Fi network.


Red, steady

Setup timed out.
Unplug the camera, plug it back in and restart setup process.

During operation



Green, blinking

Connecting to Wi
-
Fi network.


Green, steady

Connected to Wi
-Fi and operating.
Note
: The camera is always ready to record but only
originates live streaming
video when the app calls for a live stream.


Red, blinking

Not connected to Wi
-
Fi.


Low
-light operation is indicated by two small red LEDs
above
the main LED.

FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.
Unauthorized changes or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT

This
equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement
for your
information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in
strict accordance with the
manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to c
omply with the limits
for a Class B computing device in accordance with the specifications in Part 15 o
f FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not
occur in a particular
installation. If this equipment does cause interferenc
e to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

If using an indoor antenna, have a quality outdoor antenna
installed.

•

Reorient the receiving antenna until interference is reduced or eliminated.

•

Move the radio or television receiver away from the receiver/control.

•

Move the antenna leads away from any wire runs to the receiver/control.

•

Plug the receiver/control i
nto a different outlet so that it and the radio or television receiver are on different branch circuits.
•

Consult the dealer or an experienced radio/TV technician for help.

FCC / IC STATEMENT

This device complies with Part 15 of the FCC Rules, and Industry Canada’s license
-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation.

Ce
t appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’Industrie Canada. Son fonctionnement e
st soumis aux
conditions suivantes: (1) Cet appareil ne doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter t
oute interférence reçue y
compris les interférences causant une réception indésirable.
RF EXPOSURE STATEMENT
:
The antenna(s) used for this device must be installed to provide a separation distance of at least 7.8 inches (20 cm)
from all persons and must no
t be co
-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC
multi
-transmitter product procedures.

MISE EN GARDE EXPOSITION AUX FR
ÉQUENCES RADIO
: L'antenne (s) utilisée pour cet émetteur doit être installée à une distance de
séparation d'au moins 7,8 pouces (20 cm) de toutes les personnes.


DECLARACIÓN IFETEL

La operación de este equipo está sujeta a las siguientes dos condiciones

1.

Es
posible que este equipo o dispositivo no cause interferencia p
erjudicial y

2.

Este equipo debe aceptar cualquier interferencia, incluyendo la que pueda causar
su operación no deseada.

DECLARACIÓN ANATEL

Este equipamento opera em caráter secundário, isto é, não tem direito a
proteção contra interferência prejudicial, mesmo de estações do mesmo
tipo, e não pode causar interferência a sistemas operando em caráter
primário.





TRADEMARKS

Honeywell is a registered trademark of Honeywell International Inc.


For online support visit
, https://mywebtech.honeywell.com/

For the latest warranty information, visit

http://www.security.honeywell.com/hsc/resources/wa/


Ê800-
23361†Š

800
-23361
6/17
Rev. A


2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747


2017
Honeywell International Inc.

www.honeywell.com/security