Lyric-3G - Installation Manual



Related Products

AT&T Cellular Communicator for the Lyric Security System
List Price: $164.00
Our Price: $97.99

Related Categories


Document Transcript

Communicators

Lyric-3G/Lyric-3GC & Lyric-CDMA

Installation Instructions

General Information

The Lyric-3G/Lyric-3GC and Lyric-CDMA Communication Modules allow the Lyric Controller to communicate with the
Central Station via the cellular radio network.
NOTE: The Lyric-CDMA Communications Module is available only in the continental United States, Alaska and Hawaii.
IMPORTANT: Before installing the communication module, make sure power (both AC and battery) is removed from the
controller or use the “Install Cellular Module” mode described in the Communicator Module Replacement section below.

Installing the Module

1. Install the provided FCC/IC label on the control’s case back.
(Lyric-3G/3GC: P/N 800-19687; Lyric-CDMA: P/N 800-19688)

2. Remove bezel from right-hand side of control to expose the
communication module slot. To remove the bezel, push
upward then slide it out.
3. Insert the module into the slot. Push firmly to mate the edge
connector. Install the securing screw to ensure proper
connection and operation.
4. Replace the bezel.
5. After all other connections are made, power up the controller.
6. Program and register the module during the controller’s initial
association with its AlarmNet 360™ account. Refer to the
controller’s Programming Guide for details.
7. Check the signal strength before permanently locating the
Lyric Controller. See Checking Signal Strength section.

Removing the Bezel

Typical FCC/IC Label Location

Installing the communicator Module

Checking Signal Strength

When choosing a suitable mounting location, check the
communicator’s signal strength to ensure proper operation. For
most installations, using the module’s internal antenna, mounting
the Lyric controller as high as practical, and avoiding large metal
components provides adequate signal strength.
Use the Lyric Controller “Cellular Information” screen to display
signal strength (in dBm):
Security – Tools – [installer code] – Program – Comm. Diagnostics –
Cellular Information

Lyric-3G/3GC: Compare the RSCP (received signal code power
[3G]) or RSSI (received signal strength indicator
[2G]) number displayed to the Signal Strength
Guide at right to ensure adequate signal strength.

Signal Strength Guide – Lyric 3G
RSCP (3G) – if module is using the 3G Network
Good ......... -20 to -90 dBm
OK ............. -91 to -100 dBm
Marginal... -101 to -106 dBm
Bad ............ -107 to -120 dBm
RSSI (2G) – if module is using the 2G Network
Good ......... -20 to -89 dBm
OK ............. -90 to -98 dBm
Marginal... -99 to -104 dBm
Bad ............ -105 to -120 dBm

Signal Strength Guide – Lyric-CDMA
RSSI:
Lyric-CDMA: Compare the RSSI (received signal strength
indicator) number displayed to the Signal Strength Good ......... -20 to -90 dBm
OK ............. -91 to -100 dBm
Guide at right to ensure adequate signal strength.
Marginal... -101 to -106 dBm
If necessary, relocate the Controller to obtain better signal
Bad ............ -107 to -120 dBm
strength (press Cellular Information again to refresh the reading).
If adequate signal strength cannot be achieved, an external antenna should be used. See Using an External Antenna
section on other side.

Communicator Module Replacement

In the event the module needs to be replaced, the Lyric Controller must first be put in module replacement mode
(“Install Cellular Module”) to avoid causing a tamper alarm or damaging the module. Module replacement mode
deactivates tamper protection and removes power from the module connector for about 15 minutes.
1. Select the Install Cellular Module button.
End User: Security –Tools – [master code] – Advanced
Installer: Security – Tools – [installer code] –Test
a. Select Yes at the prompt to continue.
b. A popup window displays steps for module replacement.
Keep this window open until replacement is completed
2. Remove the side bezel. See diagram at right.
3. Remove the screw that secures the module.
4. Remove the communication module from its connection slot
by using the pull tab.
5. Insert the new module into the slot. Push firmly to mate the
edge connector. Replace the screw.
6. Replace the bezel.
7. When installation is complete, press OK at the replacement
steps window. Confirmation of proper installation appears.
Press OK to exit.

Replacing the Module

Using an External Antenna

Specifications

If adequate signal strength cannot be achieved, use
external antenna kit model: Cell-ANTST.

Dimensions: .... 2-5/8”W x 3-1/8”L x 1/2”D
Voltage Input .. 5V (provided by the controller)
Current
Lyric-3G/3GC
Idle ............... 60mA, standby
Transmit ..... 500mA
Lyric-CDMA
Idle ............... 75mA, standby
Transmit ..... 500mA
Environmental
Operating temperature: -20ºC to +55ºC,
(for compliance agency: 0ºC to +49ºC)
Storage temperature: -40º to +70ºC
Humidity: 0 to 95% relative humidity, non-condensing
(for compliance agency 0% to 85%)

Connecting an External Antenna

Lyric-3G/3GC Frequency Bands

2G GSM/GPRS/EDGE
Quad Band 850/900/1800/1900 MHz

RF EXPOSURE WARNING

The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 7.8 in (20 cm) from all persons and must
not be co-located or operated in conjunction with any other transmitter
except in accordance with FCC multi-transmitter product procedures.

3G UMTS Band V, Band II 850/1900MHz
WCDMA
HSUPA
HSDPA

Mise en Garde

Exposition aux Fréquences Radio: L'antenne (s) utilisée pour cet
émetteur doit être installée à une distance de séparation d'au moins 7,8
pouces (20 cm) de toutes les personnes.

IMPORTANT NOTE ABOUT EXTERNAL ANTENNAS

If an external cellular radio antenna is used, the antenna may
be installed or replaced ONLY by a professional installer.

TO THE INSTALLER – Lyric-3G

The external antenna must not exceed a maximum directional
gain (including cable loss) of 3.2 dBi at 850 MHz and 2.3 dBi at
1900 MHz.

Lyric-CDMA RF Features
• Dual-band support for both the 800MHz cellular
and 1.9GHz PCS bands.
• Adheres to CDMA authentication as specified in
CDMA 1X.
• Support for IS-95A/B and CDMA 1X Release 0/A.
External Antenna Kit: Cell-ANTST

TO THE INSTALLER – Lyric-CDMA

The external antenna must not exceed a maximum directional
gain (including cable loss) of 9.3 dBi at 850 MHz and 8.2 dBi
at 1900 MHz.

FEDERAL COMMUNICATIONS COMMISSION (FCC) & INDUSTRY CANADA (IC) STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's
Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
FCC CLASS B STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following
statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with
the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to
comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are
designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS-210 of IC. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference (2) This device must accept any interference received, including interference that may
cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS-210 des Industries Canada. Son fonctionnement est soumis
aux conditions suivantes: (1) Cet appareil ne doit pas causer d' interférences nuisibles. (2) Cet appareil doit accepter toute
interférence reçue y compris les interférences causant une réception indésirable.

SUPPORT, WARRANTY, & PATENT INFORMATION
For the latest documentation and online support, please go to:
https://mywebtech.honeywell.com/
For the latest warranty information, please go to:
www.honeywell.com/security/hsc/resources/wa.
For patent information, see www.honeywell.com/patents

MyWebTech

Ê800-21145ÄŠ
800-21145 11/15 Rev. C

Warranty

Patents

2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747

Copyright © 2015 Honeywell International Inc.
www.honeywell.com/security


Uploaded