2GIG XCVR3-GC3 - Installation Instructions for 2GIG Edge

PRODUCT OVERVIEW
The Model 2GIG-XCVR3-GC3 Transceiver Adapter is designed to be used with the 2GIG EDGE Security & Automation panel. The
Transceiver Adapter is a single frequency device. It receives and transmits 900MHz signals to and from the Alarm.com Image
Sensor (
2GIG-IMAGE2-GC3
).

PRODUCT COMPATIBILITY
The 2GIG EDGE panel
must be running firmware version 1.0 or later
to function with the Transceiver Adapter. The 2GIG-XCVR3-
GC3
must be running on firmware version 1.8 or later
to function with the panel. To check the current version number of the
firmware, go to the home screen of the EDGE panel and navigate to
System Info (2GIG Icon > System Info).

INSTALLATION INSTRUCTIONS
1. Disconnect Power

(Do Not Proceed Until this Step is Complete)

a.
Unplug the AC power supply

b.
Remove the back cover from the control panel and disconnect the backup battery cablep battery cable.

2. Wire the Transceiver Adapter to the EDGE Panel

Red: AUX + Black: Common (GND) Green: RX White: TX























3. Insert the Transceiver Adapter into the Wall

Insert the Transceiver Adapter into the wall or as far away from the EDGE panel as possible. This ensures optimum signal strength.

4. Reconnect Power

a.
After the Transceiver Adapter has been installed, re-connect the backup battery cable.

b.
Reattach the back cover to the EDGE panel and plug in the AC power supply.



Troubleshooting

If you are unable to successfully add an Image Sensor to an Alarm.com customer account, follow the recommendations below and
try again:

•
Ensure the 2GIG-XCVR3-GC3 dongle is running the required firmware
•
Double check that the Transceiver Adapter has been wired correctly to the EDGE panel

Nortek Control
5919 Sea Otter Place, Suite 100
Carlsbad, CA 92010 USA

For technical support in the USA and Canada:
Phone: 800-421-1587
Online:
www.nortekcontrol.com/support/



Limited Warranty

This Nortek Security & Control product is warranted against defects in material and workmanship of two (2) years. This warranty extends only to wholesale customers who buy direct from Nortek Security & Control
LLC or through Nortek Security & Control LLC’s normal distribution channels. Nortek Security & Control LLC does not warrant this product to consumers. Consumers should inquire from their selling dealer as to
the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Nortek Security & Control LLC for consequential damages arising out of or in connection with use or performance of
this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties for functionality, are valid only until the warranty
expires. This Nortek Security & Control LLC Warranty all other warranties expressed or implied. All products returned for warranty service require a Return Authorization Number (RA#). Contact Returns at 1-855-
546-3351 for an RA# and other important details.
FCC Regulations

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into
an outlet on a circuit different from that which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
IC
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.