Honeywell Lyric Controller - Garage Door Setup Guide

Page
42
42
Garage Door
Setup Page
43
43
Garage Door Setup
•
Lyric Smart Controller supports up to 4 garage doors.
•
To monitor the status of the door a sensor must be used
on the door.
– For easy installation, use the 5822T Tilt Sensor.
•
Garage door sensors are assigned to these zones:
– Garage Door 1
– Zone 127
– Garage Door 2
– Zone 128
– Garage Door 3
– Zone 129
– Garage Door 4
– Zone 130
5822T Page
44
44
Garage Door Setup
The following features are available when using a sensor
with the garage door.
•
View the status of the garage door.
•
Automatically close the garage door after a period of
time.
•
Automatically close the door at specific time daily.
•
Receive notifications of garage door opening, closing or
left open. (Requires Total Connect remote service)
•
System can be armed with garage door sensor open;
sensor will be protected when closed. Page
45
45
•
Zone Response Type options are:
– “Garage”
- Acts Like an Entry/Exit Zone, with Entry Delay 2
Parameters, with the Ability to Arm with the Door Open.
– “Garage Monitor” -
for Unsecured Applications and Chime
On Open.
Garage Door Setup Page
46
46
Garage Door Setup
•
Each garage door requires a 5877GDPK, which includes
the following:
FortrezZ
SSA-
1
Honeywell
5877 Page
47
47
Garage Door Setup
Note: Compatible only with garage doors using a momentary contact
closure to open/close. Page
48
48
Garage Door Setup
•
To begin Garage Door Setup, tap “Automation”. Page
49
49
Garage Door Setup
•
Tap the page down arrow “
˅
”. Page
50
50
Garage Door Setup
•
Tap “Garage door setup” from the second page of
Automation. Page
51
51
Garage Door Setup
•
Tap the first garage door to setup. Page
52
52
Garage Door Setup
•
Tap “Assign Device”. Page
53
53
Garage Door Setup
•
Tap “Enter Serial Number”.
– This is the serial number of the 5877 module. Page 54
54
Garage Door Setup
•
Enter the serial number, located on the bac
k of the 5877

m
odule,
or press the learn button on the module,
and
tap “Done”. Page
55
55
Garage Door Setup
•
Next, Include the Z-
Wave siren/strobe for garage door.
•
Tap “Include Siren”. Page
56
56
Garage Door Setup
•
Press and release the “Program Switch” on the back of
the FortrezZ siren. Page
57
57
Garage Door Setup
•
After Inclusion, tap the back arrow, “

” to return to the
Assign Device screen. Page
58
58
Garage Door Setup
•
The “Exclude Siren” button has changed to “Exclude
Garage Siren 1”, this indicates that the siren is linked. Page
59
59
Garage Door Setup
•
Use the back arrow “

” to return to Garage Doors. Page
60
60
Garage Door Setup
•
Use the back arrow “

” to return to the Automation page.
•
Tap “Garages” to continue setup of the garage door. Page
61
61
Garage Door Setup
•
Tap Garage Door 1. Page
62
62
Garage Door Setup
•
Tap the Garage Door button to open the garage door.
– The FortrezZ siren will sound for 5 seconds before opening. Page
63
63
Garage Door Setup
•
Tap again to close the garage door.
– The FortrezZ siren will sound for 5 seconds before closing. Page
64
64
Garage Door Setup
•
Tap “Edit” to rename the garage door. Page
65
65
Garage Door Setup
•
Edit the name for this garage door and tap “Save”. Page
66
66
Garage Door Setup
•
Tap “Close in” to set the time this door will automatically
close, after opening. Page
67
67
Garage Door Setup
•
Enter hours and minutes for the door to remain open
before closing automatically. (00:01 to 12:59) Page
68
68
Garage Door Setup
•
Tap “Close at” to set the time for the door to close every
day. Page
69
69
Garage Door Setup
•
Enter hour, minute and select AM or PM for the door to
close automatically each day. Page
70
70
Garage Door Setup
•
Both times are visible from the garage door control
screen.