Resolution Products RE204 - Wireless Driveway Sensor Installation Manual

Related Products

Related Categories

Document Transcript

Page 1 of 3 30-Oct-14
24-Hour Tech Support Line: (715)808-0164

RE204 Honeywell
& 2GIG
-Compatible Driveway Sensor

• For sensing Vehicles passing by.
• Sensor continuously monitors earth’s magnetic field. When the large metal
mass of a vehicle drives by, the earth’s magnetic field is twisted. The sensor
then transmits a signal wirelessly to the control panel.
• Immune to pets, wildlife, leaves, dust, sunlight.
• Weatherproof design handles all environments.
• Strong, reliable RF signal.
• 3-5 year battery life on C battery.
• Low Battery indication.

Key Instructions
• Battery “+” face away from springs. Secure batteries
with binder.
• Do not plug drain & air holes. Do not overtighten top.
• Enrolling:
Put panel in RF enroll mode.
Disconnect and then connect sensor
battery. Special transmission occurs on
power-up. Will enroll as Loop 2.
Use as a “Chime”, not an Alarm.
Supervision by panel is optional.
• Locating Sensor:
wait for 40 seconds to test each time.
1. Test max wireless range to panel, then install at no more than 2/3 of that
2. Locate sensor close enough to driveway so that Short or Medium Catch
Radius can be used. Generally, mount sensor within 12 feet of target
vehicle. Mount more than 24 feet from street.
3. Mount on a SOLID POST (the plastic pipe is not recommended), about
door-handle height, so wind cannot make it sway and false chime.

2GIG® Settings that work:
Sensor Type: (23) No Response
Equipment Type: motion
Equipment Code: (0000) other
Other Equipment Code: 0
Enter RF Serial Number: [press
SHIFT, Learn, then install battery]
Equipment Age: new
Loop Number: 2
Dialer Delay: (0) disabled
Voice Descriptor: Driveway
Reports: (0) disabled
Supervised: enabled
Chime: [set as desired]

Range Limit

Extended Catch Radius
(more likely to false chime)
Medium Catch Radius
Short Catch Radius
(more likely to miss car)
Mount sensor on
sturdy post
Door-handle height
Install at no more than
2/3 of wireless limit
Page 2 of 3 30-Oct-14
24-Hour Tech Support Line: (715)808-0164
Performance Effects:

Increased Response Decreased Response
Close to vehicle Far from vehicle
Higher (door handle level) Ground level
Slow vehicle Fast vehicle
Large metal vehicle Small vehicle with lots of plastic
Jumper on High Sensitivity Jumper on Low Sensitivity
Generally, it shouldn’t matter which direction the sensor
head is rotated. But turning it 90 degrees may cause some
performance change +/-.

Vehicle sense distance: 0 – 15 feet
Lockout time after sensing a vehicle: 30 seconds
Mounting hardware: post flange or ground stake
Replacement Battery: Energizer C-Cell (better than Panasonic)
Temperature Range: 0F to 120F
[Note: high temperatures and high humidity can have a
significant effect on alkaline battery performance.]
Housing dimensions: 5.1 x 3.8 inches

Specifications subject to change without notice.

Exploded Picture

Batteries secured
by binder
Push battery down
towards spring, and
release to cause
Do not pull
Jumper on
Short Catch Radius
(Low Sensitivity)
Jumper on Medium Catch Radius
Jumper on Extended Catch Radius
(High Sensitivity)
Page 3 of 3 30-Oct-14
24-Hour Tech Support Line: (715)808-0164

“GE”, “Honeywell”, “DSC”, “2GIG” and “Napco” are trademarks owned by General Electric
Company, Honeywell International Inc., Tyco Safety Products Canada LTD, 2GIG Technologies Inc.,
and NAPCO Security Systems, Inc., respectively.

Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or Napco
systems. However, no Resolution product is produced by, endorsed by, nor is officially associated
with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper enrollment and
operation, per control panel installation instructions, at installation.

Resolution Products, Inc. will replace products that are defective in their first five (5) years.

FCC Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
This device may not cause harmful interference.
This device must accept any interference that may be received, including
interference that may cause undesired operation.

Changes or modifications not expressly approved by the Resolution Products, Inc. could void
the user's authority to operate this equipment.


IC Notice
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may
cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1)l'appareil ne doit pas produire de brouillage, et
(2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.

IC: 8310A-RE204