2GIG Edge - Regulatory Statements (US & Canada) - Dated 031221 Rev. C
- Wireless Touchscreen Alarm Panels
- Small Business Security Systems
- Monitored Home Security Systems
- DIY Wireless Security Systems
- Apartment Security Systems
Edge Security & Smart Home System
The 2GIG EDGE Security & Smart Home System (2GIG-EDGE) is marked to indicate its compliance with:
United States—Federal Communications Commission (FCC)
Canada—Industry Canada (IC)
Please read the appropriate section that corresponds to the marking on the product before attempting to install the product.
, FCC S
Wireless Product Notice
Radio controls provide a reliable communication link and fill an important
need in portable wireless signaling; however, there are some limitations
which must be observed.
For United States installations only:
The radios are required to comply
with FCC Rules and Regulations as Part 15 devices. As such, they have
limited transmitter power and therefore limited range [approximately
400 feet (121.92 meters)].
A receiver cannot respond to more than one transmitted signal at a
time and may be blocked by radio signals that occur on or near their
operating frequencies, regardless of code settings.
Changes or modifications to the device may void FCC compliance.
Infrequently used radio links should be tested regularly to protect
against undetected interference or fault.
A general knowledge of radio and its vagaries should be gained prior
to acting as a wholesale distributor or dealer, and these facts should be
communicated to the end users.
Changes or modification not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
The 2GIG EDGE Security & Smart Home System is ETL Listed in North
America and when installed and configured as described in the 2GIG
EDGE Security & Smart Home System Installation Guide, meets the
UL STD 985: Household Fire Warning System Units and
UL STD 1023: Household Burglar Alarm Units
CAN/ULC S545: Residential Fire Warning System Control Units
ANSI/SIA CP-01-2010: Control Panel Standard - Features for False
Install according to NFPA 72. (National Fire Protection Association,
Batterymarch Park, Quincy, MA 02269). Printed information describing
proper installation, operation, testing, maintenance, evacuation, planning,
and repair service is to be provided with this equipment.
We, Nortek Security & Control, LLC of 5919 Sea Otter Place, Carlsbad, CA
92010, declare under our sole responsibility that the device complies with
Part 15 of the FCC rules.
This device complies with Part 15 of the FCC Rules and Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
This device may not cause harmful interference, and
This device must accept any interference received, including
interference received that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes:
l’appareil ne doit pas produire de brouillage, et
l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre l
Federal Communication Commission (FCC) Radiation Exposure Statement:
When using the product, maintain a distance of 20cm from the body to
ensure compliance with RF exposure requirements.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux
limites d’exposition aux rayonnements IC établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé avec un minimum
de 20 cm de distance entre la source de rayonnement et votre corps.
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada. CAN RSS-Gen/CNR-Gen
Direct all inquiries regarding this regulatory compliance statement to:
Nortek Security & Control LLC
5919 Sea Otter Place, Suite 100, Carlsbad, CA 92010 USA,
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. INCORRECT CONNECTIONS CAN RESULT IN ELECTRICAL DAMAGE.
DO NOT CONNECT THE AUX OUTPUT TO CABLES GREATER THAN 30 METERS.
BELL OUTPUT IS ONLY PROVIDED WHEN PANEL'S POWER SUPPLY IS CONNECTED TO AN AC POWER SOURCE.
1 – GND
2 – AUX+
3 – GND
4 – BELL+
5 – BELL-
6 – ZONE1
7 – ZONE2
8 – GND
9 – DCIN+
10 – DCIN-
11 – OCL1
12 – OCL2
13 – TX
14 – RX
DC Output: 5VDC +/-10% @ 500mA MAX
5-14 VDC @ 200mA MAX
2.2K +/- %5 1/4W
2.2K +/- %5 1/4W
Please test the system at least once per week.
Replacement rechargeable battery is 2GIG-EDG-BATT. Replacement batteries are available and are expected to last a minimum of three years under normal
This unit is to be checked by a qualified technician at least once every 3 years.
For installation instructions and full users guide, see
Copyright © 2021 Nortek Security & Control LLC