Rebooting The Qolsys IQ Panel 2
- Small Business Security Systems
- Monitored Home Security Systems
- DIY Wireless Security Systems
- Apartment Security Systems
In this video, Jorge shows you how to reboot the Qolsys IQ Panel 2 Plus System. An end user can perform a reboot for the panel without needing to unplug its transformer or disconnect its backup battery. The system can be rebooted or entirely powered down from the Advanced Settings Menu on the panel.
Performing a reboot will have the system power cycle and automatically power back on after it has powered down. A shut down will have the panel power down and remain powered down. You will need to hold the power button on the side of the panel to power it back on. Performing a reboot is typically done as a troubleshooting step. It is also performed automatically when performing a system firmware update. You may want to power down the panel if you are planning to make hardware changes, or if you are planning on not using the system for a while. You can also choose to have the system display its Setup Wizard when it is powered back on. This will assist you or a new user with setting up the system for the first time.
Remember, your system will not be able to communicate with the Alarm.com Servers for monitoring or automation purposes while the system is powered down. For that reason, you will usually want to keep it powered on at all times. And if you do power it down for some reason, then you should make sure to power it back on as soon as possible. The system will automatically reestablish its connection with Alarm.com, provided that you have a proper communication path set up and the system properly registered for alarm monitoring service. Alarm Grid customers must have a Gold or Platinum Level Plan (Self or Full) to use the Qolsys IQ Panel 2 Plus for alarm monitoring. If the system is not powered on, then it will be unable to recognize system events and alert Alarm.com when said events occur.
Hi, DIY-ers. I'm Jorge from AlarmGrid. Today, I'm going to be showing you guys how to reboot your Qolsys IQ Panel 2 or the IQ Panel 2 Plus. It's the same process, and there's two very, very easy ways to do this. The first way, there's an actual Panel Reboot button in the Advanced Settings. And then two, there is a Power Down button, if you guys want to do a hard reboot where you guys can power the system down and then remove the backup battery and the power supply from the wall or the little barrel connector that plugs into the actual system. And I'm going to show you guys how to do both of them. Now, if you guys are going to be doing the panel reboot and even the panel power down, you will need to know the master code, the installer code, or the dealer code. As long as you have either one of those three codes, you should be able to panel reboot or power down the system very easily. So the first thing we're going to go ahead and do is right here, I have my IQ Panel 2. I'm going to hit the little top button here to open up my settings. And then I'm going to hit the little wrench to open settings. Now from there, you're not going to see the panel reboot or the power down function just yet. You need to go to Advance Settings. Enter user code. That's where it's going to ask you to enter a your user code and you need to use your master code, your installer code, or your dealer code. I'm going to show you guys all three. So my master code, my panel's defaulted so I'm going to use 1234. That is an IQ 2 Panel's default master code. If you guys just got a brand new IQ Panel 2 or an IQ Panel 2 Plus, your default master code is 1234. As you see here, I have a Panel Reboot and a Power Down button. I'm going to hit the back arrow key to go back one screen and I'm going to go back into Advanced Settings. Enter user code. And now, I'm going to go ahead and use my installer code and my dealer code. So my installer code will be 1111. And you'll see there, I have a Panel Reboot and I also have a Power Down. The installer code is what you're going to be using to program in sensors, to basically program your system. I'm going to back out one more screen and I'm going to go to Advance Settings. Enter user code. And this time, I'm going to use my dealer code which is 2222. And you'll see here, this brings me more to more dealer settings-- dealer branding, a couple of other things that dealers usually have access to. Now, either one of these codes will work-- master, installer code, or dealer code. And all the codes that I've used today are all default codes, basically treating this panel as if it was brand new. If you guys have changed your codes or if your company has changed your codes and you're trying to enter in the codes and they're not working, you know why. So as you see here, every single screen that we've had has had Panel Reboot and Power Down. The first reboot option is going to be the Panel Reboot. This will simply power cycle your IQ Panel 2 or your IQ Panel 2 Plus. And if you hit OK, the panel will start rebooting. I'm going to go ahead and hit Cancel, just to show you guys what a hard reboot will look like because that actually goes a little more into death. If you do a Panel Reboot and you hit OK, the panel will shut down and then it'll power back up on its own. Now sometimes, whenever you're doing the panel reboot, you may be asking why you need it. Let's say for an activation, sometimes the cellular signal takes a little bit to ping in to the Alarm.com servers when you're being activated. So sometimes what a panel reboot does is it kind of resets everything. It refreshes everything and it makes everything go a little bit faster. So sometimes an activator or a technician may ask you to reboot your system, whether it's a simple panel reboot or whether it's a hard reboot. Do not do the reboots until a technician tells you to do it. One other thing, you know how sometimes you power down a computer or a laptop or even a gaming station or anything like that, even a router as well, sometimes you need a power them down, give them a little break to power them backup, even your cell phone. Same thing with the alarm system. Sometimes every now and then they need to be powered down for 30 seconds and then turned back on. So we saw with the panel reboot how to access that. Now let's go ahead and go into the power down. Now I'm going to show you guys how to do a complete power down where you remove the backup battery, and where you remove the transformer or the AC power to the system. When you guys are doing this hard reboot, it's very important that you power the system down first and then remove these parts. Simply removing the backup battery and the AC power supply while the system is still powered on could cause corruption of the system. You could break your system, short circuit it, so you want to make sure that you power the system down first before you remove anything. So I'm going to go ahead and hit Power Down. Power Down is going to ask me if I want to relaunch the wizard on the next power up. I'm just going to uncheck that because I do not want to relaunch the wizard. And it even says here, are you sure you want to shut down? Disconnecting the power supply and/or battery before the shut down process is complete may result in data corruption and/or panel failure. Important-- to continue, press shut down and wait for the LED buttons to turn completely off then unplug the battery followed by the power supply. So I'm going to hit OK. System will say power off, shutting down. As soon as this light here on the right hand side, that's green, goes completely dark, then I can go ahead and take my system off the cover, unplug the backup battery, and unplug the power supply. So the light is off, the screen is dark, no button presses make the screen power on. I can now go ahead and take the system off of the backplate. There's two tubs here at the very top. Wait a second. OK. So here, you have the back of the IQ 2. You see, this is my power supply right here. It plugs into this little barrel connector. And my backup battery is right here. So the system is completely powered down so you can easily, if you wanted to do a hard reboot, unplug the backup battery, and you can unplug the power supply. One moment. And now I have my IQ 2 free from a backup battery and free from the power supply. This is how you do a hard reboot. Now, to power it back on, you can just plug everything right back in the same way it was. Plug the barrel connector and make sure it's all the way in, and plug the backup battery, it'll snap in. And once you have that, you can mount the system back onto the backwall, onto backplate, make sure you fish the antenna through the back if you're using the IQ 2 Plus for your PowerG sensors. And it snaps shut onto the backwall. Now, I must have accidentally pressed the little side button here when plugging it back in which is why you see the screen come on. But normally, the screen won't come on until you actually press that side button, which is the power button. Now, you see the system's powering back on and that was how you do a hard reboot. So you have the panel reboot, which is just a simple reboot. And then you have a hard reboot where you actually shut the system down, you manually take out the power supply and the backup battery, and then you plug everything back in and then you power back on. If you guys have any questions on how to reboot your IQ Panel 2 or your IQ Panel 2 Plus, please email us to email@example.com. If you found the video helpful, make sure you hit Like underneath. Subscribe to the YouTube channel and hit the little bell icon to enable notifications, so whenever we upload new content, you guys get notified. I'm Jorge, and I'll see you guys next time.