Honeywell Defaulting AlarmNet Communicators



Related Products

AlarmNet 25' RF Antenna Coax Cable
List Price: $90.00
Our Price: $69.99
AlarmNet 50’ RF Antenna Coax Cable
List Price: $140.00
Our Price: $107.99
AlarmNet 5' RF Antenna Coax Cable
List Price: $60.00
Our Price: $46.99
AlarmNet GSM-ANT3DB Antenna Mounting Bracket
AlarmNet Internet Alarm Monitoring Communicator
List Price: $160.00
Our Price: $139.99
AlarmNet LYNX Plus Internet Alarm Monitoring Communicator
AlarmNet 25’ Antenna Kit
List Price: $220.00
Our Price: $162.99
AlarmNet 50’ Antenna Kit
List Price: $260.00
Our Price: $197.99
AlarmNet Antenna Kit
List Price: $120.00
Our Price: $92.99
AlarmNet Remote Weatherproof GSM Antenna
List Price: $110.00
Our Price: $80.99
AlarmNet Indoor 10’ Remote GSM Antenna
AlarmNet External Antenna Accessory
AlarmNet Cellular Alarm Monitoring Communicator
AlarmNet LYNX Touch Cellular Alarm Monitoring Communicator
AlarmNet LYNX Touch Cellular Alarm Monitoring Communicator
AlarmNet LYNX Plus Cellular Alarm Monitoring Communicator
AlarmNet Total Connect 2.0 Upgrade Kit
AlarmNet Cellular Alarm Monitoring Communicator
AlarmNet Total Connect 2.0 Upgrade Kit
AlarmNet High Security Dual Path Alarm Monitoring Communicator
AlarmNet Dual Path Alarm Monitoring Communicator
AlarmNet Total Connect 2.0 Upgrade Kit
AlarmNet LYNX Touch Internet Alarm Monitoring Communicator
List Price: $130.00
Our Price: $96.99
AlarmNet Alarm Communicator Battery Backup
List Price: $20.00
Our Price: $13.99
AlarmNet MMCX to SMA Adapter Cable
AlarmNet LYNX Touch WiFi Alarm Monitoring Communicator
List Price: $100.00
Our Price: $64.99
AlarmNet VISTA-21iP Cellular Alarm Monitoring Communicator
AlarmNet SMA to N Adapter Cable
List Price: $35.00
Our Price: $22.99

Related Categories


Document Transcript

Step-by-Step

Steps to Default GSM Radio Programming
1) Plug in 7720P programmer; you should have the following display:

7720P PROGRAMMER

2) Press the Enter (#) key and you will have the following on the display:

Strt Prog Mode? Y/N?

3) Select the Shift key and then the Y/N key (for a Yes response) and then Enter (#). You will then see:

Program Device? Y/N
4) Select the Shift key and then the Y/N key (for a Yes response) and then Enter (#). You will then see:

Device Mode ECP
5) Hit the Shift key and then BS/ESC. You will then see:

Review? Y/N

-1-

Tech Support Updated 4/20/09

Step-by-Step
6) At the Review? Y/N prompt, select No (do not hit shift) and hit Enter (#). You should then see:

Create Password? Y/N
7) Again select No and hit Enter (#). You will then see:

Exit Prog Mode? Y/N
8) Select Shift, then the BS/ESC key again and you should see:

Set Defaults? Y/N
9) Select Shift, then the Y/N button (for a Yes response) and hit Enter (#). 10) The programmer will then ask you again if you want to create a password (see above), you will answer “No” again and hit Enter (#). 11) The programmer will then ask if you want to exit program mode again. This time answer “Yes” and hit Enter. The programmer will then display the below three screens and the device will be reset to manufacturing default values:

Checking Root File TX Path….

Updating Root File

Done Resetting!!

12) Please note: If you do not have connection to the network, you will see the screen below instead. Simply answer No to the question and the unit will still default.

Cannot Upload Try Again? Y/N

-2-

Tech Support Updated 4/20/09


Uploaded