Frequently Asked Questions
Can I use the Lynx-WEXT with my Qolsys IQ Panel 2?
Yes, the Lynx-WEXT can be used with the Qolsys IQ Panel 2. By adding the Lynx-WEXT to your Qolsys panel, an external siren, or sirens, drawing up to 1.2 Amps of current can be supported. The Lynx-WEXT contains everything except the siren. Learn more about adding a high current siren here.
How Does a Fire Detector Work?
There are two primary methods for detecting a fire. These are through either smoke detection and heat detection. For that reason, a "fire detector" is more commonly referred to as a "smoke detector" or a "heat detector". There are also combo smoke and heat sensors. Learn more about these devices.
Where Should I Install My Motion Detector?
There are several things you should keep in mind when choosing a location for a motion detector. The ideal location for a motion detector is in the corner of a room and away from any windows. The device should be placed 6 to 8 feet off the ground. Learn more about where to install a motion sensor.
How Do I Wire a 4-Wire Smoke Detector to My Wired Alarm System?
Connecting a 4-wire smoke detector to a wired alarm system is a slightly more complicated process than setting up most other hardwired zones. Several wired connections will need to be made. The setup will also require an end of line resistor and a relay module. Learn more about 4-wire smokes.
How Do I Replace an Existing Honeywell 5816 On My VISTA Security System?
Replacing an old Honeywell 5816 door and window contact on a VISTA Panel is a very easy process. Simply delete the serial number of the old sensor from the panel. Then learn in the new one. Finally, uninstall the old sensor and install the new one. Learn more about replacing the Honeywell 5816.
How Do I Connect My Qolsys IQ Panel 2 to a Garage Door?
A Qolsys IQ Panel 2 can connect with a Z-Wave garage door controller. This will allow the panel to open and close a garage door, and the panel will show whether the garage door is opened or closed. This can also be done using the Alarm.com service. Learn more about Z-Wave garage door controllers.
Which Glass Break Sensors Work w/ ADT Security Systems?
ADT equipment is often comparable to that of Honeywell. In fact, many ADT sensors are simply re-branded Honeywell sensors. For that reason, Honeywell glass break sensors will often work with ADT alarm systems. Learn more about which glass break sensors are compatible with ADT security panels.
How Do I Turn Off Alarm Reporting for a Honeywell 5800 Series Motion Sensor?
Alarm reporting for a Honeywell 5800 Series Motion Sensor can be turned off through zone programming. This will instruct the system to not send out a distress signal to the central station if an alarm event involving that sensor were to occur. Learn more about alarm reporting on a motion sensor.
Can I Add a Wired Siren to the Qolsys IQ Panel 2?
A wired siren can be added to a Qolsys IQ Panel 2 system. The device connects to the siren outputs on the back of the IQ Panel 2. The siren is powered using any 12VDC plug-in transformer. Once installed, it will function automatically. Learn more about using a wired siren with an IQ Panel 2.
Why Did My Panel Report Code E903 "Start FW"?
A Honeywell VISTA Panel will send the E903 Start FW message to the monitoring station prior to its firmware update process. This message indicates that the firmware update process has begun. Learn more about the E903 Start FW message and what it means for your Honeywell VISTA Panel.
Yes, the Lynx-WEXT can be used with the Qolsys IQ Panel 2. By adding the Lynx-WEXT to your Qolsys panel, an external siren, or sirens, drawing up to 1.2 Amps of current can be supported. The Lynx-WEXT contains everything except the siren. Learn more about adding a high current siren here.
Added:
How Does a Fire Detector Work?
There are two primary methods for detecting a fire. These are through either smoke detection and heat detection. For that reason, a "fire detector" is more commonly referred to as a "smoke detector" or a "heat detector". There are also combo smoke and heat sensors. Learn more about these devices.
Added:
Where Should I Install My Motion Detector?
There are several things you should keep in mind when choosing a location for a motion detector. The ideal location for a motion detector is in the corner of a room and away from any windows. The device should be placed 6 to 8 feet off the ground. Learn more about where to install a motion sensor.
Added:
How Do I Wire a 4-Wire Smoke Detector to My Wired Alarm System?
Connecting a 4-wire smoke detector to a wired alarm system is a slightly more complicated process than setting up most other hardwired zones. Several wired connections will need to be made. The setup will also require an end of line resistor and a relay module. Learn more about 4-wire smokes.
Added:
How Do I Replace an Existing Honeywell 5816 On My VISTA Security System?
Replacing an old Honeywell 5816 door and window contact on a VISTA Panel is a very easy process. Simply delete the serial number of the old sensor from the panel. Then learn in the new one. Finally, uninstall the old sensor and install the new one. Learn more about replacing the Honeywell 5816.
Added:
How Do I Connect My Qolsys IQ Panel 2 to a Garage Door?
A Qolsys IQ Panel 2 can connect with a Z-Wave garage door controller. This will allow the panel to open and close a garage door, and the panel will show whether the garage door is opened or closed. This can also be done using the Alarm.com service. Learn more about Z-Wave garage door controllers.
Added:
Which Glass Break Sensors Work w/ ADT Security Systems?
ADT equipment is often comparable to that of Honeywell. In fact, many ADT sensors are simply re-branded Honeywell sensors. For that reason, Honeywell glass break sensors will often work with ADT alarm systems. Learn more about which glass break sensors are compatible with ADT security panels.
Added:
How Do I Turn Off Alarm Reporting for a Honeywell 5800 Series Motion Sensor?
Alarm reporting for a Honeywell 5800 Series Motion Sensor can be turned off through zone programming. This will instruct the system to not send out a distress signal to the central station if an alarm event involving that sensor were to occur. Learn more about alarm reporting on a motion sensor.
Added:
Can I Add a Wired Siren to the Qolsys IQ Panel 2?
A wired siren can be added to a Qolsys IQ Panel 2 system. The device connects to the siren outputs on the back of the IQ Panel 2. The siren is powered using any 12VDC plug-in transformer. Once installed, it will function automatically. Learn more about using a wired siren with an IQ Panel 2.
Added:
Why Did My Panel Report Code E903 "Start FW"?
A Honeywell VISTA Panel will send the E903 Start FW message to the monitoring station prior to its firmware update process. This message indicates that the firmware update process has begun. Learn more about the E903 Start FW message and what it means for your Honeywell VISTA Panel.
Added: