Honeywell VISTA-15P Frequently Asked Questions
How Do I Enter Walk Test Mode on a Vista Panel?
You can enter walk test mode on the Vista-15P, 20P, 21iP panels by keying in Installer Code + [5] + [0]. The panel must be "Ready" to access test mode.
How do you power cycle a Honeywell VISTA?
Disconnect the positive leg of the battery. Find the plug-in transformer, unscrew it from the center of the outlet then unplug the transformer. Learn how to power cycle a Vista.
Will the Central Station Call Me if I Disarm My Alarm just After a False Alarm?
There is a possibility, when you disarm immediately after a false alarm, that the central station will see the cancellation signal, and not call you. Read on!
Will My Monitoring Company Change My Installer Code?
It is possible an alarm company will change the installer code for the security system. Some companies do this as a way of limiting what the user can do.
What is a Transmitter Sniffer Test on a Vista Panel?
The transmitter sniffer test is used to verify that programming for wireless zones is correct, and that the devices are transmitting. Read on to learn more!
Is there a Battery in a 2WT-B Photoelectric i3 Sensor?
No, the 2WT-B smoke detector, by System Sensor, is a low voltage smoke detector that gets its power from an alarm panel. Read on to see how the 2WT-B works.
What Is the Valid Address for a 4219?
The address required for a 4219 8-zone hardwired expander depends which panel it will be used with. Keep reading to learn valid addresses for the 4219.
How Do I Wire a 6162RF to a VISTA?
The 6162RF has 4 wires, two for power, and two for data. It connects to the keypad bus of the Vista panel. Learn to wire the 6162RF to a Vista panel.
How do I Set up a Honeywell 6160RF?
The 6160RF must be connected to the alarm panel, then properly addressed in order to work. Continue reading and learn how to set up the 6160RF keypad receiver.
How Do I Perform a Transmitter Sniffer Test on a Vista Panel?
Enter Installer Code + [#] + [3] to begin the transmitter sniffer test. The system must be ready, with no faults or bypasses, in order to enter this mode.
You can enter walk test mode on the Vista-15P, 20P, 21iP panels by keying in Installer Code + [5] + [0]. The panel must be "Ready" to access test mode.
Added:
How do you power cycle a Honeywell VISTA?
Disconnect the positive leg of the battery. Find the plug-in transformer, unscrew it from the center of the outlet then unplug the transformer. Learn how to power cycle a Vista.
Added:
Will the Central Station Call Me if I Disarm My Alarm just After a False Alarm?
There is a possibility, when you disarm immediately after a false alarm, that the central station will see the cancellation signal, and not call you. Read on!
Added:
Will My Monitoring Company Change My Installer Code?
It is possible an alarm company will change the installer code for the security system. Some companies do this as a way of limiting what the user can do.
Added:
What is a Transmitter Sniffer Test on a Vista Panel?
The transmitter sniffer test is used to verify that programming for wireless zones is correct, and that the devices are transmitting. Read on to learn more!
Added:
Is there a Battery in a 2WT-B Photoelectric i3 Sensor?
No, the 2WT-B smoke detector, by System Sensor, is a low voltage smoke detector that gets its power from an alarm panel. Read on to see how the 2WT-B works.
Added:
What Is the Valid Address for a 4219?
The address required for a 4219 8-zone hardwired expander depends which panel it will be used with. Keep reading to learn valid addresses for the 4219.
Added:
How Do I Wire a 6162RF to a VISTA?
The 6162RF has 4 wires, two for power, and two for data. It connects to the keypad bus of the Vista panel. Learn to wire the 6162RF to a Vista panel.
Added:
How do I Set up a Honeywell 6160RF?
The 6160RF must be connected to the alarm panel, then properly addressed in order to work. Continue reading and learn how to set up the 6160RF keypad receiver.
Added:
How Do I Perform a Transmitter Sniffer Test on a Vista Panel?
Enter Installer Code + [#] + [3] to begin the transmitter sniffer test. The system must be ready, with no faults or bypasses, in order to enter this mode.
Added: