Frequently Asked Questions
What Is the Best Alarm Contact?
There is no single best alarm contact. Many different types of door and window contacts are available, and the best one depends on the needs of the user. There are several questions to ask when looking for an alarm contact so that you can obtain the perfect one. Learn more about alarm contacts.
Why Did My Panel Report Code E339 "Power on Reset"?
A Honeywell Panel will report the message E339 "Power on Reset" when its communicator has been reset. The communicator for a Honeywell System will reset whenever programming changes are sent to the module or when the module is powered off and then back on. Learn more about the E339 message.
Can I Add a Wired Siren to the Qolsys IQ Panel 2?
A wired siren can be added to a Qolsys IQ Panel 2 system. The device connects to the siren outputs on the back of the IQ Panel 2. The siren is powered using any 12VDC plug-in transformer. Once installed, it will function automatically. Learn more about using a wired siren with an IQ Panel 2.
How Do I Install an Alarm.com Camera?
Most Alarm.com Cameras are installed in a very similar manner. These cameras come with a mounting plate and screws. After drilling some holes, the mounting plate can be screwed into the wall. The camera can then be attached to the mounting plate. Learn more about installing an Alarm.com Camera.
How Do I Connect My Qolsys IQ Panel 2 to a Garage Door?
A Qolsys IQ Panel 2 can connect with a Z-Wave garage door controller. This will allow the panel to open and close a garage door, and the panel will show whether the garage door is opened or closed. This can also be done using the Alarm.com service. Learn more about Z-Wave garage door controllers.
How Do I Turn Off Sensor Supervision for a Honeywell 5800 Series Motion Sensor?
Sensor supervision on a 5800 Series Motion Sensor is used by an alarm system to check-in with the sensor and make sure that it is within range and communicating properly. Turning this off will have the panel not look out for any check-in signals from the sensor. Learn more about sensor supervision.
How Do I Turn Off Alarm Reporting for a Honeywell 5800 Series Motion Sensor?
Alarm reporting for a Honeywell 5800 Series Motion Sensor can be turned off through zone programming. This will instruct the system to not send out a distress signal to the central station if an alarm event involving that sensor were to occur. Learn more about alarm reporting on a motion sensor.
Do I Need Dispatch If I Live In An Apartment?
Just because you live in an apartment doesn't mean that you shouldn't have central station monitoring with automatic dispatch. If you want help to be automatically sent out to your home in the event of an emergency, then you must have dispatch. Learn more about central station monitoring.
Which Systems Can Alarm Grid Take Over?
Alarm Grid will support any alarm system that we can take over. To take over a system, the user may need to know the panel's Installer Code and/or Master Code. In some situations, the user will need to replace the system's communicator. Learn more about what systems we can take over.
What Is the Tamper On My Alarm System For?
The tamper switch is a very important feature on an alarm system. This feature tells the system to produce an instant alarm if someone tries to physically break into the panel while the system is armed. This prevents an intruder from powering down the panel. Learn more about tamper switches.
There is no single best alarm contact. Many different types of door and window contacts are available, and the best one depends on the needs of the user. There are several questions to ask when looking for an alarm contact so that you can obtain the perfect one. Learn more about alarm contacts.
Added:
Why Did My Panel Report Code E339 "Power on Reset"?
A Honeywell Panel will report the message E339 "Power on Reset" when its communicator has been reset. The communicator for a Honeywell System will reset whenever programming changes are sent to the module or when the module is powered off and then back on. Learn more about the E339 message.
Added:
Can I Add a Wired Siren to the Qolsys IQ Panel 2?
A wired siren can be added to a Qolsys IQ Panel 2 system. The device connects to the siren outputs on the back of the IQ Panel 2. The siren is powered using any 12VDC plug-in transformer. Once installed, it will function automatically. Learn more about using a wired siren with an IQ Panel 2.
Added:
How Do I Install an Alarm.com Camera?
Most Alarm.com Cameras are installed in a very similar manner. These cameras come with a mounting plate and screws. After drilling some holes, the mounting plate can be screwed into the wall. The camera can then be attached to the mounting plate. Learn more about installing an Alarm.com Camera.
Added:
How Do I Connect My Qolsys IQ Panel 2 to a Garage Door?
A Qolsys IQ Panel 2 can connect with a Z-Wave garage door controller. This will allow the panel to open and close a garage door, and the panel will show whether the garage door is opened or closed. This can also be done using the Alarm.com service. Learn more about Z-Wave garage door controllers.
Added:
How Do I Turn Off Sensor Supervision for a Honeywell 5800 Series Motion Sensor?
Sensor supervision on a 5800 Series Motion Sensor is used by an alarm system to check-in with the sensor and make sure that it is within range and communicating properly. Turning this off will have the panel not look out for any check-in signals from the sensor. Learn more about sensor supervision.
Added:
How Do I Turn Off Alarm Reporting for a Honeywell 5800 Series Motion Sensor?
Alarm reporting for a Honeywell 5800 Series Motion Sensor can be turned off through zone programming. This will instruct the system to not send out a distress signal to the central station if an alarm event involving that sensor were to occur. Learn more about alarm reporting on a motion sensor.
Added:
Do I Need Dispatch If I Live In An Apartment?
Just because you live in an apartment doesn't mean that you shouldn't have central station monitoring with automatic dispatch. If you want help to be automatically sent out to your home in the event of an emergency, then you must have dispatch. Learn more about central station monitoring.
Added:
Which Systems Can Alarm Grid Take Over?
Alarm Grid will support any alarm system that we can take over. To take over a system, the user may need to know the panel's Installer Code and/or Master Code. In some situations, the user will need to replace the system's communicator. Learn more about what systems we can take over.
Added:
What Is the Tamper On My Alarm System For?
The tamper switch is a very important feature on an alarm system. This feature tells the system to produce an instant alarm if someone tries to physically break into the panel while the system is armed. This prevents an intruder from powering down the panel. Learn more about tamper switches.
Added: