Frequently Asked Questions
Will an Interlogix Simon XT Work w/o a Phone Line?
The only way for a Simon XT to receive monitoring without a phone line is with cellular service. Either a phone line or cellular service is needed for the panel to send outbound signals. Also, no communicator is needed to use the panel as a local sounder. Learn more about the Simon XT.
Will Alarm.com Work w/ an Interlogix Simon XT?
Alarm.com is the interactive service used with a Simon XT System. The service is used to arm and disarm the system, check the status of sensors and control Z-Wave devices. A Simon XT must have active cellular service before it can work with Alarm.com. Learn more about the Simon XT and Alarm.com.
How Do I Add Additional User Codes to an Interlogix Simon XT?
The Simon XT System will support up to eight different user codes. These codes are used for arming and disarming the panel, and they are set up through System Programming. You will need to know the Master Code for the system to create new user codes. Learn how to set up user codes on a Simon XT.
What Happens to an Interlogix Simon XT When Internet Goes Down?
The loss of internet does not impact an Interlogix Simon XT in any sort of way. This is because the Simon XT cannot use an IP connection. Instead, it must communicate using cellular service or a telephone connection. Learn more about the communication paths used with an Interlogix Simon XT.
Will 2GIG Sensors Work on an Interlogix Simon XT?
The Interlogix Simon XT is compatible with wireless sensors that operate at a wireless frequency of 319.5 MHz. However, 2GIG sensors operate at a wireless frequency of 345 MHz. This means that they are not compatible with the Simon XT System. Learn which sensors are compatible with the Simon XT.
How Do I Add a Key Fob to an Interlogix Simon XT?
A key fob is enrolled with an Interlogix Simon XT through the System Programming Menu. With the system in its learn more, press and hold the top two buttons on the key fob. This will enroll it with the system. You must then adjust its settings. Learn more about using a key fob with a Simon XT.
How Do I Add a Wireless Zone to an Interlogix Simon XT?
Wireless zones for an Interlogix Simon XT are configured through the System Programming Menu. With the system in its learn mode, activate the sensor tamper to learn it in. Then configure the settings for that zone. Learn how to enroll a wireless sensor with an Interlogix Simon XT System.
Is an Interlogix Simon XT Z-Wave Compatible?
An Interlogix Simon XT can only support Z-Wave devices if a Z-Wave controller is added to the system. This addition comes in the form of a cellular module with an integrated Z-Wave Controller. Once Z-Wave is added, it can be controlled in various ways. Learn how to use Z-Wave with a Simon XT System.
How Do I Control Lights w/ an Interlogix Simon XT?
The Simon XT can interface with Z-Wave lights after a Z-Wave controller has been added to the system. The controller comes integrated with the Alarm.com cellular module. In order to integrate with Z-Wave, the Simon XT needs an active cellular plan. Learn more about using Z-Wave with a Simon XT.
How Do I Change the Date or Time on an Interlogix Simon XT?
Setting the date and time on an Interlogix Simon XT is a very easy process. The options for adjusting the date and time can be accessed from the main screen of the system. You will need to know the system Master Code to change the date and time. Learn more about using an Interlogix Simon XT.
The only way for a Simon XT to receive monitoring without a phone line is with cellular service. Either a phone line or cellular service is needed for the panel to send outbound signals. Also, no communicator is needed to use the panel as a local sounder. Learn more about the Simon XT.
Added:
Will Alarm.com Work w/ an Interlogix Simon XT?
Alarm.com is the interactive service used with a Simon XT System. The service is used to arm and disarm the system, check the status of sensors and control Z-Wave devices. A Simon XT must have active cellular service before it can work with Alarm.com. Learn more about the Simon XT and Alarm.com.
Added:
How Do I Add Additional User Codes to an Interlogix Simon XT?
The Simon XT System will support up to eight different user codes. These codes are used for arming and disarming the panel, and they are set up through System Programming. You will need to know the Master Code for the system to create new user codes. Learn how to set up user codes on a Simon XT.
Added:
What Happens to an Interlogix Simon XT When Internet Goes Down?
The loss of internet does not impact an Interlogix Simon XT in any sort of way. This is because the Simon XT cannot use an IP connection. Instead, it must communicate using cellular service or a telephone connection. Learn more about the communication paths used with an Interlogix Simon XT.
Added:
Will 2GIG Sensors Work on an Interlogix Simon XT?
The Interlogix Simon XT is compatible with wireless sensors that operate at a wireless frequency of 319.5 MHz. However, 2GIG sensors operate at a wireless frequency of 345 MHz. This means that they are not compatible with the Simon XT System. Learn which sensors are compatible with the Simon XT.
Added:
How Do I Add a Key Fob to an Interlogix Simon XT?
A key fob is enrolled with an Interlogix Simon XT through the System Programming Menu. With the system in its learn more, press and hold the top two buttons on the key fob. This will enroll it with the system. You must then adjust its settings. Learn more about using a key fob with a Simon XT.
Added:
How Do I Add a Wireless Zone to an Interlogix Simon XT?
Wireless zones for an Interlogix Simon XT are configured through the System Programming Menu. With the system in its learn mode, activate the sensor tamper to learn it in. Then configure the settings for that zone. Learn how to enroll a wireless sensor with an Interlogix Simon XT System.
Added:
Is an Interlogix Simon XT Z-Wave Compatible?
An Interlogix Simon XT can only support Z-Wave devices if a Z-Wave controller is added to the system. This addition comes in the form of a cellular module with an integrated Z-Wave Controller. Once Z-Wave is added, it can be controlled in various ways. Learn how to use Z-Wave with a Simon XT System.
Added:
How Do I Control Lights w/ an Interlogix Simon XT?
The Simon XT can interface with Z-Wave lights after a Z-Wave controller has been added to the system. The controller comes integrated with the Alarm.com cellular module. In order to integrate with Z-Wave, the Simon XT needs an active cellular plan. Learn more about using Z-Wave with a Simon XT.
Added:
How Do I Change the Date or Time on an Interlogix Simon XT?
Setting the date and time on an Interlogix Simon XT is a very easy process. The options for adjusting the date and time can be accessed from the main screen of the system. You will need to know the system Master Code to change the date and time. Learn more about using an Interlogix Simon XT.
Added: