Alarm Grid Video Recap September 10th - 17th

Posted By

Hi DIYers! We're here with the Alarm Grid video recap for September 10th thru 17th. Our support technicians Joe, Dylan and Jorge are all back and here to teach you how to use your alarm system. We have seven new videos this time, with most of them focusing on the Interlogix Systems.

Disabling Chime on an Interlogix Simon XT

Dylan demonstrates how to disable the chime for an Interlogix Simon XT System. By disabling the chime, the panel will not produce any sounds when sensors are faulted. There is an option accessible from the main screen that is used with toggling the chime On and Off. If the option is set to Off, the chime will be disabled for the entire system. Alternatively, muting the system will also stop the panel from producing chimes. However, this will stop all system sounds, except for sirens.

Self Monitoring a Simon XT

Dylan talks about using a Simon XT with a self-monitoring plan. A self-monitoring plan means that the system is not connected with a central monitoring station. As a result, a user will be unable to receive automatic emergency dispatch. But a user will still be able to receive system alerts and notifications through text and/or email from A user can take these notifications and contact the authorities when needed to keep their home or business safe.

Adding a Wireless Motion Sensor on an Interlogix Simon XTi

Jorge shows users how to add a wireless motion sensor to an Interlogix Simon XTi System. This is the same process that is used for enrolling a wireless sensor to an Interlogix Simon XTi-5 System. A motion sensor will actively search for any motion that is present in an area. If the device detects motion while the system is armed, an alarm will occur on the system. This makes these devices great for keeping the inside of a building protected and secured. The Simon XTi supports 319.5 MHz motion sensors.

Resetting an Interlogix Simon XTi and XTi-5 to Factory Defaults

Jorge demonstrates how to reset an Interlogix Simon XTi or XTi-5 System to factory default settings. Once the system has been defaulted, all programmed codes and sensors will be deleted. The Master, Installer and Dealer Codes will all be reset to the factory default values. All system settings will be restored to the default. A user will basically need to reprogram their entire panel after a factory default has been performed. Therefore, we usually only recommend a default if it is absolutely needed.

Adding Hardwired Zones to an Interlogix Simon XT

Dylan shows users how they can use hardwired sensors with the Simon XT System. There are a couple of ways that this can be done. The panel has two hardwired inputs for supporting two normally closed hardwired sensors. This is a great option if a user only needs to use a couple of sensors. The other option is to use a compatible wired to wireless converter. This is good for using several wired sensors. A good converter to use is the Qolsys IQ Hardwire 8 or 16.

Sensors Compatible with a Qolsys IQ Panel 2 Alarm System

Joe talks about which sensors can be used with the Qolsys IQ Panel 2. The standard IQ Panel 2 contains a wireless receiver for supporting 319.5 MHz sensors. This includes all Qolsys Sensors and Interlogix/GE Sensors. If Qolsys S-Line Sensors are used, then they will be encrypted. Additionally, the upgraded Qolsys IQ Panel 2 Plus can support 915 MHz PowerG Sensors, plus one type of legacy sensors. This depends on which legacy daughtercard is installed. There are legacy options for 319.5 MHz, 345 MHz (Honeywell 5800 Series & 2GIG) and 433 MHz (legacy DSC).

Demonstrating Installer Code & Dealer Code on a Simon XTi and XTi-5

Joe explains the differences between the Installer Codes and Dealer Codes on the Simon XTi and XTi-5 Systems. Both of these codes are set to 4321 out of the box. However, they can be individually programmed if desired. The Dealer Code can do a few things that the Installer Code cannot. These mostly deal with the dialer for the system. Other than that, these codes serve exactly the same purpose. We generally recommend leaving these codes set to their default of 4321 so that the user does not get locked out of programming.

Tags: , ,