Cellbounce CB34U-D-RES01A Posts

Time for the CellBounce to, well, bounce. This device, which served as a temporary bridge for AT&T customers clinging to their 3G communicators, is now being discontinued. For those who rely on CellBounce to convert 3G signals for use on the LTE network, it's time to consider the next steps.

Mark your calendars: as of May 1, 2025, AT&T will officially cease support for CellBounce devices on its network. This means if you're currently relying on a CellBounce to bridge the gap between your old AT&T 3G/4G communicator and the AT&T LTE network, it's time to upgrade.

Failure to upgrade to a new LTE communicator, or a new system before the deadline will likely result in a complete loss of communication, compromising alarm signals. This includes critical life-safety signals like fire and carbon monoxide alerts.

You may be wondering which communicator to choose. Below, we'll give you some suggestions for how best to move past the Resideo CellBounce and that old 3G/4G communicator:

We realize upgrading to a new panel may be a big undertaking for a DIYer. We've got content on upgrading from a VISTA-20P to a VISTAH3 and on upgrading from several older panels to the PROA7PLUS:

• Upgrade from an L3000 to a PROA7PLUS
• Upgrade from an L5200 to a PROA7PLUS
• Upgrade from an L5210 to a PROA7PLUS
• Upgrade from an L7000 to a PROA7PLUS

If you fail to replace the Resideo CellBounce before the deadline, here's what you may experience:

• Communication Failures: "Comm fail," or communication failure, means your alarm system's regular check-in with AlarmNet didn't happen and they sent a message to the monitoring station. These supervision check-ins usually occur daily or monthly. If a comm fail happens, the monitoring station will normally contact the alarm dealer, who will then contact you, though exact procedures may vary. For Alarm Grid customers with cellular communicators, these check-ins are typically set for every day. It is possible that your system is set as "unsupervised". If that is the case, your system might be incapable of communicating and neither you nor the monitoring station would know.
• Trouble message on display. This issue can vary widely, depending on your panel type and supervision settings. When a cellular communicator is in use, there is a "cell fault time" setting within communicator programming. By default, this is usually set to 60 minutes. With this setting, if the communicator loses contact with the cellular network for 60 consecutive minutes, a trouble message is displayed by the panel. This means you'll likely see that there is a problem before your alarm dealer. This may be displayed as a bF or Check 103 depending on the panel and keypad used. If a CellBounce is the issue, the most effective way to clear this message permanently is to disable the cellular communicator in panel programming. This will effectively disable cellular reporting. A better option is to upgrade the communicator or the system.

If you happen to have an IP and GSM communicator, it is usually possible, depending on your communicator version, to disable only the cellular path for the communicator. This will leave the IP communicator working. This might be a temporary solution, until you can upgrade to a new LTE communicator, or a new system.

The CellBounce was always intended as a short-term fix for a long-term problem. Let's face it, some people just don't like being told they have to upgrade their stuff. I remember when the old 2G network shut down, I had family members who clung to their old phones right up until the bitter end! But eventually, we all have to move with the times. Funny thing is, those same family members wouldn't give up their smartphones without a fight today.

ISC West, the security industry's largest trade show, was held this week in Las Vegas. This is the first year since the COVID-19 outbreak that the show is being held in person. We didn't attend the show this year, but based on what we've seen, JCI and Qolsys won the ISC West show in 2022.

Qolsys:

IQ Pro

Qolsys, Inc. which was acquired by Johnson Controls in 2020, premiered two brand new products, and reintroduced one more. The IQ Pro Panel is a hybrid wired and wireless system which targets large homes, and medium to large businesses. It combines the reliability of hardwired components with the range and versatility of the DSC PowerG Sensor lineup. The product is planned for release in Summer, 2022.

There is very little information available about the IQ Pro. The Press Release announcing the product, which was released by Johnson Controls, didn't even say for certain that it would be a Qolsys branded product, though with 'IQ' as a part of the name, we assume it will be. This panel will combine elements of the IQ Panel 4 with the DSC PowerSeries Neo, and a little bit of customer feedback thrown in. A couple of things we do know, the IQ Pro will offer the choice of either Ethernet or WIFI connectivity along with LTE. This panel has been designed with Alarm.com for Business in mind, to take advantage of all the extended features offered there.

IQ WIFI 6

The Qolsys IQ WIFI 6 was actually first introduced to us here at Alarm Grid last year. It is a product we thought was going to released then, but it was introduced at ISC West and should be available in Summer, along with the IQ Pro. The IQ WIFI 6 is is a router that uses 802.11 1/b/g/n/ac/ax WIFI-6 technology. It offers dual-end 2.4 GHz and 5 GHz MIMO mesh architecture on a Qualcomm Networking Pro 400 platform. It will integrate with Qolsys touchscreen panels, to allow a user to administer the network from there.

The IQ WIFI 6 will offer four (4) network partitions, including a Guest Network and a dedicated network for the end-user's WIFI devices. Both of these will switch automatically between 2.4 GHz and 5GHz for seamless optimization of WIFI performance. In addition to these partitions, there are two (2) private network partitions to be used by security and/or networking providers. By separating the security, surveillance, and smart home devices from the rest of the network, professional providers can cut down on disruptions caused by user error.

IQ Hub

The Qolsys IQ Hub has actually already been released, in a limited fashion within the last six (6) months or so. Presumably due to supply chain issues, Qolsys has tightly controlled how many of these panels are shipped, but now, based on a press release this week, it seems like they may be looking to perform a wider release. The IQ Hub differs from the IQ Panel 4 in several ways, one of which is that each panel will only support one RF product line. There is a PowerG version with either an AT&T or Verizon communicator. This is the only version that has been released at this time. Soon however, there will be a version that supports unencrypted, uni-directional Honeywell and 2GIG wireless sensors, one that supports unencrypted, uni-directional Interlogix and all Qolsys wireless sensors, and a version that supports uni-directional DSC 433 MHz wireless sensors.

Resideo:

Cellbounce

Resideo and Honeywell Home brought the Cellbounce to ISC West. This device will bridge communicators that work on the AT&T 3G network over to the AT&T LTE network, without having to replace the device. This is a plug-n-play device. It connects to an outlet within range, which is 25' (7.62m), of the existing AT&T 3G communicator, though be sure not to plug the Cellbounce in until it has been configured by your alarm dealer.

It syncs to the 3G communicator, then with the LTE network and any signals sent by the communicator will be picked up and transported via LTE. It even works with Total Connect 2.0, though it does not work with two-way voice. It also only works in the contiguous United States, so Alaska, Hawaii, and Puerto Rico residents, the Cellbounce is not for you. There are some other caveats and limitations, so be sure to read our product description carefully before purchasing.

2GIG, Nortek Control:

2GIG Edge

In October of 2021 Nortek Control, the parent company of 2GIG, was purchased by Nice. Nice originated in Italy, with Nice North America handling the US and Canadian segment of the business. This year at ISC West, Nice put their stamp on this relatively new acquisition. In addition to some commercial camera innovations by Linear, Nice/Nortek Control announced during ISC West that they will offer exclusive integration between the 2GIG Edge security panel and the ELAN Home Control platform. The Edge has been out for about a year now. You can read all about it here.

According to their press release, this integration will be supported by the ELAN SC-100 and ELAN SC-300 system controllers running ELAN 8.7 OS (which won't be available until April, 2022). The 2GIG Edge panel requires firmware version 3.1.1.0 or later. Firmware can be pushed through Alarm.com or downloaded. This panel firmware version is not available from 2GIG just yet, but once it is posted, our page will be updated. One of the more convenient features of this integration is the ELAN Control Auto Zone Detection feature. If the ELAN system is setup first, with zone names, once the 2GIG Edge is installed, it can download all zones and zone names directly from ELAN, without having to re-enter the information.

A recent blog post about the looming AT&T 3G Sunset contained an error. We mentioned in that blog that the ingenious Resideo Cellbounce, a 3G to LTE converter, does not support Total Connect 2.0. That is incorrect. As long as the original 3G device supports TC2, the Cellbounce also supports it.

This misinformation has been updated in the original post, but for those who may have already read it, we wanted to also briefly touch on it here. In brief, the Resideo Cellbounce is a plug-and-play device. It plugs into a standard 110 Volt AC outlet and should be mounted within 25' (7.6m) of the working AT&T 3G Communicator. The Cellbounce connects to the 3G communicator, and to an AT&T LTE network. Once those connections have been made, it acts as a bridge, receiving the 3G information and transmitting it through the LTE network.

AT&T has committed to supporting the Resideo Cellbounce unit until at least the end of April, 2025. It is possible that support may go beyond that date, but the contractual obligation ends on May 1. Since the Cellbounce is plug-and-play, anyone can install it. An Installation Professional is not required. Though, it is important to note that the Cellbounce should not be powered on until after the information has been added to the customer account by the alarm dealer.

The Cellbounce will arrive in a box with a Serial Number and an IMEI number printed on it. This information must be provided to the alarm dealer so that they can attach the unit to the proper customer account. This step must be performed BEFORE the Cellbounce is powered on. Once power is applied, within a few minutes the Cellbounce will connect to the existing communicator and to the LTE network. LEDs on the unit will signal when these connections take place. From there it's just a matter of testing to be sure signals are going through successfully. Just be sure to put your system on test with the monitoring station prior to beginning this process.

The Resideo Cellbounce is only compatible with AlarmNet AT&T 3G communicators. The existing communicator must be registered and working. This means it can't be in a comm failure condition. Adding a Cellbounce to a communicator that is in comm failure will not correct that issue.

We are in the midst of a strange confluence of events. The COVID-19 pandemic has wreaked havoc on both manufacturing and supply chains, with both sub-assembly parts and product delivery being affected. Add to that the AT&T 3G/4G GSM sunset and you'll have a good picture of where we are today.

We've known about the AT&T sunset for some time. We've written about it in this blog on numerous occasions. Alarm Grid implemented an email campaign to proactively remind our customers who needed an upgrade not to wait until the last minute. But there will always be people who want to wring every last bit of usefulness out of their current product, before upgrading to a new one. I don't blame them, really. But the strange confluence of events I mentioned earlier may find those folks scrambling to upgrade at the last minute.

Security communicator manufacturers, including Resideo, and Alarm.com are doing everything they can to bridge the gap between supply and demand. They are introducing new product lines, with alternatives to standard LTE such as those that use the LTE Cat-M1 network. Resideo has introduced the LTEM-PA and LTEM-PV and they are beta testing the LTEM-IA for future release. The benefit of these products is that they provide nearly the same experience as the previously released LTE products, but either due to happenstance or good planning, components for these products are readily available, so while other LTE products are on backorder, these units are plentiful.

Alarm.com also has a series of LTE Cat-M1 System Enhancement Modules (SEM), including the Alarm.com ADC-SEM300-VT-AT-M (coming soon) and the ADC-SEM300-VT-VZ-M which is available for purchase now. Both of these SEMs are compatible with the Honeywell VISTA product line (with the exception of the VISTA-128 and VISTA-250 panels). They allow compatible VISTA panels to communicate using Alarm.com, and to work with the Alarm.com remote control features. These are dual-path communicators that also have a Z-Wave plus controller built in. Alarm.com will soon have the ADC-SEM210-PS-AT-M and the ADC-SEM210-PS-VZ-M. These dual-path communicators with Z-Wave Plus controllers will support the older DSC Power Series panels (PC1616, PC1832, PC1864 all version 4.20+).

Perhaps the most intriguing "Bridge the Gap" product available currently is the Resideo Cellbounce. This product has some limitations, it only works with AT&T 3G communicators, it only works in states within the contiguous US (sorry Alaska, Hawaii, and Puerto Rico), and it can only be installed with a communicator that is currently still registered and active on the AT&T 3G network. If the communicator is in comm failure, this condition has to be resolved before a Cellbounce can be added. There are some other limitations too, such as it can't support Total Connect 2.0, (CORRECTION: It CAN support TC2 as long as the original AT&T 3G communicator supports it.) But be sure to read the full product description linked above before deciding to purchase.

The Cellbounce is a plug-and-play device. Anyone can install it, so no installer visit is required. It can work with any Honeywell or Resideo AT&T 3G communicator. The Cellbounce is installed within range, which is 25' (7.6m), of an existing, registered AT&T 3G communicator. The Alarm Dealer will need the Serial Number and IMEI Number from the Callbounce unit. These can be found on the box the device comes in.

Important Note: Provisioning must take place on the AlarmNet360 server BEFORE the Cellbounce unit is powered on.

Once the Cellbounce has been provisioned, it should be powered up using an unswitched outlet, not a power strip. From there, the Cellbounce does all the heavy lifting. On one hand, it reaches out and finds an LTE signal, on the other, it reaches out to the existing 3G communicator and locks on to it. Once both of these connections have been made, any time the 3G communicator sends a signal, the Cellbounce captures it and transfers it to the LTE network. AT&T has promised that the Cellbounce units will continue to function until at least Q1 2025. This should give any Cellbounce users plenty of additional time to upgrade. There are a limited number of Cellbounce units available, so if this sounds like an attractive option for you, order yours today. Don't get left behind!

Sunset Graphic courtesy of AlarmNet360: