Service Announcements Posts

We have received word from Resideo that some SkyBell Cameras may temporarily experience delays when being used with Total Connect 2.0 or through the SkyBell App. The issue is most likely the result of SkyBell servers being overloaded. Resideo is working with SkyBell to address this issue.

Earlier today, we mentioned a proactive warning issued from Alarm.com stating that doorbell cameras may experience delays when being used with their platform. We believe that this is due to the increased usage of these devices for the Halloween holiday. It is likely that a similar issue is affecting the general SkyBell servers. This is not something you should be overly concerned about, and the issue should be addressed soon.

If you are experiencing any major issues, or if you would like to learn more about these potential delays, please email us at support@alarmgrid.com. Remember that we're here to help!

Update: This issue has since been resolved.

Alarm.com has put out a proactive warning ahead of Halloween night (October 31st) stating that customers may notice minor delays between the hours of 5pm and 11pm ET. These delays should only affect non-critical, non-emergency signals and notifications, as well as doorbell cameras.

Alarm.com did not release an official reasoning for these likely delays, but we suspect that it will be the result of increased activity from the excellent Alarm.com SkyBell Video Doorbells due to Trick-Or-Treaters. And as we all know, SkyBell Cameras are the best video doorbells out there!

We think it's good for Alarm.com to give out this proactive warning just in case there are any delays. In the mean time, you can rest assured that any critical signals, including alarms, will still go through for Alarm.com. If you are an Alarm Grid customer seeking more information about the issue, then please email us at support@alarmgrid.com. We look forward to hearing from you!

Alarm.com has reported that their service is experiencing a technical issue that may be hindering the signaling ability of customer accounts. You may have trouble accessing the Alarm.com Mobile App or website during this time. The issue is currently being worked on and should be solved soon.

Alarm Grid will provide an update once we learn more.

Update 4:45 pm ET: We have learned that Alarm.com customer interfaces have stabilized. Command and signal processing has also improved. However, some customers may still experience intermittent delays during this time. The issue should be fully resolved shortly.

Update: The issue has since been resolved.

Alarm.com Rogers Communicators may be experiencing connectivity issues due to a temporary issue with the carrier. No other carriers are affected. We expect the issue to be resolved relatively soon. Alarm Grid will provide further updates once we receive more information from Alarm.com.

Update: This issue has since been resolved. Please contact us at support@alarmgrid.com if you are continuing to experience issues.

Hi DIYers! We have some important information that is applicable for anyone with central station monitoring service from Alarm Grid. Our alarm monitoring partner, Criticom Monitoring Services (CMS), has announced some important changes regarding their text and email notifications.

Starting December 1st, 2019, all text message notifications and automated notifications from Criticom will come from the short code 60281. We recommend marking this number with your phone service provider so that it is not blocked as part of anti-spam measures. Additionally, all automated email notifications from Criticom will come from noreply@myalarms.com. You should mark this email so that any incoming messages do not end up in your spam folder.

Additionally, CMS has alerted us that blocked calls to customers have been reported. This is due to anti-spam measures put into place by phone companies. As an Alarm Grid customer, it is crucial that you are able to receive incoming phones calls from CMS at all times. Failure to answer these calls may result in unnecessary emergency dispatch. We have actually discussed this subject at length before in a previous blog post.

We recommend saving ALL contact numbers for CMS in your contacts list. It is also recommended that you contact your phone carrier directly and ask them to allow incoming calls from these numbers. We also understand that some customers may have downloaded third party apps that will detect and block incoming toll-free and/or believed "spam" numbers. If you have one of these apps, you should delete it, or adjust its settings so that CMS phone numbers are not blocked.

As a reference, the five (5) phone numbers listed below are associated with Criticom Monitoring Services, and they should not be blocked or ignored under any circumstance:

• Longwood, FL: (800) 432-1429
• Manasquan, NJ: (800) 631-2299
• Cypress, CA: (714) 373-7000; (800) 468-4640; (800) 482-9800

Keep in mind that you may not always receive incoming phone calls from the same CMS phone number. In the event that one monitoring center is temporarily taken offline for any reason, any incoming alarms will be automatically re-routed to a different monitoring center. This redundancy helps ensure that customers always get the help they need when alarm events occur. For that reason, make sure to save all five (5) of the CMS phone numbers listed above.

You may also want to sign-up for text notifications from CMS. Text messages sent from CMS are sent from the CMS secure short code that should not be blocked under any circumstance. Remember, this short code will be 60281 starting December 1st, 2019. This number should be saved as a contact in your phone so that you can quickly recognize any incoming message as being associated with your security system and/or monitoring service.

If you want to learn more about our monitoring plans that include central station service, we recommend checking out our alarm monitoring page. If you have any questions, you should email us at support@alarmgrid.com. Remember that our team responds to emails during our regular support hours of 9am to 8pm ET M-F. We look forward to hearing from you and answering any questions you have about monitoring service.

Hi DIYers! Today, we want to discuss an unusual quirk we found with Alarm.com. It turns out that the Alarm.com platform cannot receive alerts from temperature sensors. This is important for any Alarm.com user who wants to receive remote alerts for unusually high or low temperatures.

When you use sensors with a security system, the expectation is that you will be able to receive alerts from an interactive service platform whenever the device is activated. But with Alarm.com, the platform cannot receive incoming signals from a system regarding faulted Temperature Zones. This means that you cannot use Alarm.com to receive text and/or email alerts regarding an activated temperature sensor.

We discovered this issue due to a customer using a DSC PG9905 Temperature Sensor with a Qolsys IQ Panel 2 Plus System. We quickly discovered that the issue also applied to any temperature used with an Alarm.com Security System. This is important to note, as we know that many users out there will want to know about any unusual temperatures in their homes and businesses. Many people rely on using these sensors with their security systems so that they know if their HVAC systems break before serious and expensive damage occurs.

Fortunately, there is still another way you can receive alerts from Alarm.com regarding an unusually high or low temperature. If you pair a Z-Wave thermostat with your system, then you can set up notifications to be sent out whenever the detected temperature goes outside of a set threshold. A good Z-Wave thermostat to use for this application is an Alarm.com ADC-T3000 Thermostat. This thermostat also supports the ADC-S2000 Temperature Sensor, which will allow you to monitor the temperature in a second area of the building as well.

Another option is to use the Total Connect 2.0 platform with a Resideo Security System instead. Unlike Alarm.com, the Total Connect 2.0 service can be set up to send out text and/or email notifications for any sensor type, including temperature sensors. The Resideo LYNX Touch and Lyric Systems also have designed Temperature Zones that are used with Z-Wave thermostats to end high-low temperature alerts to AlarmNet360 and TC2 whenever an unusual temperature is detected. Just make sure that any Temperature Zone is noted as such on your central station document. These zones are frequently mistaken for 24-hour auxiliary medical zones.

If you have any questions about the functionality of temperature sensors, the Alarm.com and Total Connect 2.0 platforms, or any of our other products or services, please email us at support@alarmgrid.com. Remember that our support hours are from 9am to 8pm ET M-F. We also recommend checking out our monitoring page to learn more about our monitoring services. We look forward to hearing from you and providing top-quality monitoring service for your home or business.

UPDATE: This issue was later addressed in Qolsys IQ Panel 2 Plus Firmware Update 2.5.0. Please see this post for more information.

We have learned that there are some temporary server issues affecting the Total Connect 2.0 service. These issues may lead to "latched" alarms and/or trouble conditions. Users may also experience delays using the TC2 platform and have trouble logging into their accounts during this time.

As a result of these issues, users may find that system alarms and trouble conditions are becoming "latched" on their Total Connect 2.0 account. This means that these events are still appearing on TC2, even though the issue has been cleared locally. You should be able to clear these events by using the "Refresh Status" button on TC2. If you find that you cannot clear these events, then you should email us at support@alarmgrid.com so that we can clear them for you. Please note that other TC2 functions, such as remote access and system alerts, should still be operating as normal.

Alarm Grid has reported these issues to Resideo's AlarmNet360 division, and the problem is being addressed at this time. We expect the matter to be resolved as soon as possible. We will provide an update when the matter is fixed. Stay tuned to our blog for updates.

Update: Resideo has reported that the issue has been resolved as of about 5:30pm ET.

Resideo is currently in the process of pushing automatic OTA firmware updates to all active AT&T LTE Communicators. The updating process is ongoing, and we are not sure how long it will last. You should not notice any changes to your monitoring service or your Total Connect 2.0 account.

If you recall a few months ago, we announced that Resideo was pushing down automatic over-the-air (OTA) firmware updates to LTE communicators. Resideo started with the Verizon LTE Communicators, and now they are updating the AT&T LTE Communicators. This is a very similar update with no major differences.

Just like before, Resideo is expected to perform this update cycle in batches. Units that were registered first will have the update performed first. This will continue in sequential order until all active Resideo AT&T LTE Communicators have been updated. Any new AT&T LTE Communicator activated during this time will be placed at the end of the queue. If an update fails, that communicator will be pushed to the next batch to try again.

Remember, the communicator must be active and connected with the AlarmNet360 Servers in order for the update to go through. Any communicator that is not active will not be able to receive the update. This includes any communicator installed inside a panel that is currently powered off. Try and keep your panel powered on at all times to ensure that the update can go through successfully.

The following Resideo Communicators are affected by this update:

• Honeywell LYRICLTE-A for Lyric Controller
• Honeywell LTE-L57A for L5210 and L7000
• Honeywell LTE-IA for VISTA Panels
• Honeywell LTE-XA for VISTA Panels
• Honeywell LTE-L3A for L3000

It is possible that your panel may reboot as part of the updating process. However, you should not notice any other changes. Additionally, the following Contact ID messages may be generated during the process:

If you have any questions regarding this update, please do not hesitate to email us at support@alarmgrid.com. Remember that our support hours are from 9am to 8pm ET M-F. We look forward to hearing from you and answering your questions!

Hi DIYers! We are excited to learn that Firmware Version 2.4.0 is now available for the Qolsys IQ Panel 2 and IQ Panel 2 Plus. The update can easily be applied at the panel or pushed from Alarm.com. Many new features and automation capabilities come included with the firmware update.

The following updates to the system are applied with Firmware Version 2.4.0:

Improved User Interface (UI)
- Ability to Hide Security, Lock, and Thermostat Pages
- Dynamic Screen Lock Page - Enable Independently from Partitions
- All-New Automation & Wellness Pages

Improved Partitions 2.0
- Global Arming
- Bluetooth Disarming by Partition

LiftMaster MyQ Garage Control
- New Panel UI for LiftMaster Garage Door Devices Paired w/ Alarm.com

ADC Scene Control
- Control Alarm.com Scenes Directly from Panel

IQ Remote Enhancements
- Alarm.com Videos thru Built-In Camera
- Live-Stream ADC Cameras and Video Doorbell thru IQ Remote (No Audio)
- Connectivity Improvements

Home Automation
- Support for Z-Wave Version 6.81.03 - Including S2 Security & SmartStart
- Note: Only for Panels Manufactured w/ 2.4.0 & Above; Not for Panels Receiving Update OTA
- Support for LQI 2 (link quality indicators)
- Emergency Heat Mode for Z-Wave Thermostats now supported

PowerG
- PowerG Modem Firmware Update 80.25
- Fixes Compatibility with the DSC PG9312 Outdoor Contact

Panel Motion
- Sensitivity Settings - High, Medium, Low
- Mask-Off Up to Four (4) Distinct Areas

Other
- QR Code Scanning for S-Line Sensor Enrollment (319.5 MHz Panel Only)
- Language Improvements

While we will certainly be showing off these features in greater detail sometime in the near future, for now we just want to show you how to download the new firmware. You can have the update pushed down automatically from the Alarm.com servers free of charge. Alarm Grid customers can do this by emailing us at support@alarmgrid.com. You will need to have the panel monitored with Alarm Grid and connected to WIFI for us to do this.

But the easiest way to update is to apply the update yourself at the panel. Again, make sure your system is monitored and connected to WIFI before you begin. It will also need to be plugged-in and not have a low-battery condition. Start from the main screen of the system. Click on the small grey bar at the top. Choose Settings > Advanced Settings > Installer Code (default 1111) > Upgrade Software > Patch Tag > type in iqpanel2.4.0 > OK > Upgrade Using Network. If done correctly, the new firmware update should be downloaded. Once it has been completely downloaded, press "OK" to begin the update process. The panel will reboot as part of the update. The entire process will take around five (5) minutes and is complete after the reboot.

If you have any questions about this update, please email us at support@alarmgrid.com. This looks to be a very exciting update for the IQ Panel 2 plus, and we can't wait for you to check it out. We will be showing off some of these features in greater detail in the coming days. Keep checking our blog for more information!

We have learned that the LYNX Connect App has been discontinued. The app can no longer be downloaded from the Apple App Store or the Google Play Store. Users wanting a second on-site option for controlling a LYNX Touch should use either a keypad or Total Connect 2.0, or upgrade to the Lyric.

The LYNX Connect App is a handy tool for many LYNX Touch users, It allows users to control a LYNX Touch System from a separate on-site device, all while enjoying the same user interface as the LYNX Touch System itself. The LYNX Touch Panel must have an L5100-WIFI Card installed and be on the same WIFI network as the device that is using the app to control the system. The app is designed for use with the L5100, L5200, L5210, and L7000 systems.

A very common application of the LYNX Connect App is to use it on a tablet that is mounted to the wall. By doing this, you can essentially have the tablet operate as a touchscreen keypad for the system. Many users find this to be a desirable option, as it is really the only way to obtain a secondary touchscreen controller for a LYNX Touch. By using a cheap tablet, you can readily establish a great secondary keypad for your system. Unfortunately, the discontinuation of the app means that this is no longer an option for many LYNX Touch users.

It turns out that all Firmware Versions 9 and higher for the LYNX Touch Systems does not work with the LYNX Connect App. In order to support the LTE communicators, a LYNX Touch System will need to be on some Firmware Revision that is higher than Firmware Version 9. The minimum Firmware Revision required depends on which LTE module you are using.

The LTE-L57A requires Firmware Revision 9.00.209 or higher, while the LTE-L57V requires Firmware Revision 9.00.201 or higher. Rather than update the app to make it compatible with the newer versions, Resideo made the decision to discontinue support. As a result, it is no longer possible to get the app for an Android or iOS device. Remember that the latest LYNX Touch Firmware Version is only available for the L5200, L5210 and L7000 Systems. If you have an L5100, then your system is running a lower Firmware Version, and it will still work with the app.

If you already have the LYNX Connect App downloaded, and your LYNX Touch System is running less than Firmware Version 9, then you can still continue to use the app. Many L5210 and L7000 users who use IP-only monitoring never upgraded to the latest Firmware Version. This is because the newer Firmware Versions only really benefit users with cellular connectivity. Just be aware that if you ever need to replace your Android or iOS device, you will not be able to re-download the app. And if you ever upgrade to Firmware Version 9 or higher on your panel, then the app will no longer work.

Remember that Firmware Version 9.00.201 or higher is needed to use the LTE-L57V, and Firmware Version 9.00209 or higher is needed to use an LTE-L57A. These updates are very important, as LTE is so crucial. If you want to replace a tablet that served as a secondary keypad using the LYNX Connect App, then you have a couple of options available. One possibility is to get a Honeywell 5828 or Honeywell 5828V Keypad. Both keypads will pair nicely with any LYNX Touch System.

You might also consider using Total Connect 2.0. This is an interactive monitoring platform that you can use to control your system from anywhere. TC2 is even more versatile and beneficial than the LYNX Connect App. This platform can be used to access the alarm system from virtually anywhere using the Total Connect 2.0 Mobile App. Since you can access it on a smartphone, many users find that it is even more convenient than setting up a second keypad.

Another option is to upgrade to the Resideo Lyric Alarm System. The Lyric has its own app called the MyHome Controller App that works in the same manner as the LYNX Connect App. The MyHome Controller app is still actively supported by Resideo, and it allows a tablet or smartphone to serve as a reliable secondary keypad. Other benefits for the Lyric include HomeKit compatibility, increased zone support, and its encrypted sensor options.

We apologize for any inconvenience that this may have caused. If you have any questions or concerns about the loss of the LYNX Connect App, or if you want to learn more about Total Connect 2.0, then we invite you to reach out to us. Our team is happy to help you determine the best replacement keypad option for your needs. The best way to contact us is by email at support@alarmgrid.com. You may also call us at (888) 818-7728 during our regular business hours of 9am to 8pm EST. We look forward to hearing from you!