Alarm Communicators Posts

No need to consult your Magic 8 Ball on this one, we'll be glad to help you answer it! In short: if your alarm system or communicator runs on Alarm.com or AlarmNet, it likely isn't locked to one company. It just needs to be properly released from the original provider's monitoring account.

Homeowners may assume their alarm system belongs to whoever installed it. If a monitoring company set up the equipment, doesn't that company own it forever? Not necessarily. Alarm.com and AlarmNet (the network behind Resideo's Total Connect service) aren't owned by any single monitoring company. So once your system is released from the current account, any other monitoring company affiliated with the communication platform can pick up the monitoring.

What Makes a System "Non-Proprietary"

Most modern security panels talk to a monitoring company through one of a few shared networks. Two of the most common are Alarm.com and AlarmNet. Neither network is owned by a single monitoring company. Dozens of providers, including Alarm Grid, offer monitoring on panels that use them.

That's different from a proprietary system, where the panel only works with one company's software and can't be reprogrammed to work with anyone else. If your panel uses Alarm.com or AlarmNet, there's a good chance it was built to be flexible from day one, even if the company that installed it isn't.

The Exception: Some Equipment on These Networks Is Still Proprietary

Running on Alarm.com or AlarmNet doesn't automatically mean a system is open to any provider. Some companies build their own locked-down equipment on top of these shared networks. This shows up most with ADT, but Vivint and a few other large providers do it too. The hardware often comes from the same manufacturers everyone else uses, but it ships with a company-specific firmware, a modified part number, or an account binding that ties it to one provider alone.

If you own one of these proprietary devices, you'll generally need to replace it before you can switch monitoring companies, even though under the hood it communicates over one of these shared networks. One thing to look for is a company-specific tag added to an otherwise standard part number, like the "-ADT" or "-BRK" endings in the table below. If you're not sure whether your panel is proprietary, check the exact model number printed on the panel or the communicator and ask a prospective new monitoring company to confirm before you commit to switching.

A note on the list below: these model numbers came from online research, not from the manufacturers or monitoring companies themselves. Because this kind of information is treated as proprietary, we have limited ability to confirm it's fully accurate or current. If your equipment matches, or looks close to, one of these models, confirm its status with a prospective monitoring company before assuming anything either way.

What About Ring and SimpliSafe?

You'll also see Ring and SimpliSafe promoted heavily any time you search for a security system, especially as a DIY installer. These aren't professional-grade systems, meaning professional installers likely aren't installing them, and they're a different kind of proprietary than the ADT and Vivint equipment described above. Neither Ring nor SimpliSafe run on Alarm.com or AlarmNet. Instead, they're built on their own closed platforms from the ground up, so there's no shared network to release your equipment into.

If you want ongoing monitoring on a Ring or SimpliSafe system, you're locked into their monitoring plans (Ring Protect or SimpliSafe's monitoring service) for as long as you own that hardware. Switching providers on this kind of system generally means replacing the equipment in its entirety, not simply requesting a release of your system.

The Real Rule: One Company at a Time

Here's the part that trips people up. A non-proprietary system can only be monitored by one company at a time. While your equipment is active on an account with your current provider, no other company can take over monitoring for it, even though the technology may allow it. The system has to be released from the original account first.

This is where some customers get stuck. Say you've decided to cancel, your equipment is paid off, and you're no longer under contract with the installing company. At your request, your alarm company should release the equipment so you can take it to a new provider.

Some companies make this difficult. They may tell you your system or its communicator can't be used anywhere else. In most cases involving non-proprietary Alarm.com or AlarmNet equipment, like the kind described as non-proprietary above, that isn't true. The system can be used elsewhere. It just needs to be released first.

In most circumstances, AlarmNet and Alarm.com will not facilitate the release of a system. Think of your old monitoring company and your prospective new one as warring nations. In this analogy, AlarmNet and Alarm.com are Switzerland. They don't take sides. One exception to this rule is when the original monitoring company is defunct and your equipment is stuck tied to an account nobody is managing anymore.

How Alarm Grid Handles It

Alarm Grid was built around the idea that customers should never feel trapped. We don't use contracts. We don't charge activation fees. We don't charge cancellation fees.

If you ever decide to cancel your account with us, we'll ask why. We'll see if there's anything we can do to fix the problem or find you a better plan. But once it's clear you want to move on, we process the cancellation and release your equipment. That frees it up to be picked up by any other monitoring company that supports your system's platform, whether that's Alarm.com or AlarmNet.

Know Before You Buy (or Switch)

If you're shopping for alarm monitoring, or thinking about switching providers, ask these questions before you sign up with anyone. First, does the equipment run on Alarm.com or AlarmNet? Second, is any of the equipment proprietary? Third, does the company require a contract, and do they charge fees for cancellation or early termination? The answers will tell you how much freedom you'll actually have down the road.

Ready to make the switch, or start fresh with an easy, no-contract monitoring plan? You can email us with questions at support@alarmgrid.com or call us at 888-818-7728. We're here Monday - Friday from 9:00 AM - 8:00 PM Eastern Time, and happy to help you figure out whether your current system can be moved to a new provider.

ADT, Vivint, Brinks Home Security, Ring, and SimpliSafe are trademarks of their respective owners. Alarm Grid is not affiliated with, endorsed by, or sponsored by any of these companies.

Replacing a First Alert PROA7 or PROA7PLUS panel sounds simple enough. Alarm dealers perform replacements daily using AlarmNet360 (AN360), and when the recommended process is followed, everything works fine. But for a DIYer with no AN360 access, the proper order of things may not be clear.

DIY users often run into a unique problem. While in the process of replacing their existing PROA7 or PROA7PLUS, they also decide to add to the system and purchase new PROSIX sensors for that purpose. The hood's already up, might as well give it a tune up, right?

We've seen customers receive their replacement panel and immediately begin adding new sensors before performing the actual panel swap. We get it, new sensors are exciting! But please curb your enthusiasm until you've worked with one of our support agents to move all existing PROSIX sensors from the old panel to the new one. Otherwise, you may lose either your original PROSIX sensors or the new ones you've already added.

Why This Happens

Unlike older wireless sensors, PROSIX devices become permanently paired, or “married,” to a specific alarm panel during enrollment.

Once a PROSIX sensor is learned into a system, it cannot simply be moved to another panel later unless it is properly released from the original system first.

That means if you:

• Power up a replacement PROA7 or PROA7PLUS
• Enroll new PROSIX sensors into it
• Then later perform a panel replacement in AN360

...you may unintentionally overwrite sensor programming during the restore process.

This can go wrong in any number of ways, but the end result of not following the proper steps is that you lose sensor programming, and the affected sensors may not be recoverable. Once a PROSIX sensor has been paired with a system and powered on for 24 hours or more, it can no longer be factory defaulted. So a sensor in this position, paired with a system that no longer exists with no possibility of being factory defaulted, is a sensor that must be replaced.

But the Panel Does Exist!

Yes...and no. When a PRO Series panel is registered and communicating properly with AlarmNet360, the panel and server stay in constant sync. If programming changes, AN360 updates the panel "image" stored on the server. During a panel replacement, this saved image is transferred to the new PROA7 or PROA7PLUS.

If you get a new panel and begin programming it with new PROSIX sensors, you're creating a new and separate image. One that isn't synced with AN360. When the panel pairs with a PROSIX sensor, it chooses a channel for communication. You may be familiar with this process from older 2.4 GHz WIFI networks. The panel makes its choice based on the least noisy channel at the time of sensor programming. This information becomes part of the new image.

If that channel later becomes noisy, the panel can switch to a cleaner channel and notify all enrolled PROSIX sensors to follow it. If a sensor misses that message, it may remain stuck trying to communicate on the old channel. For more information on PROSIX wireless best practices, check out this FAQ.

The proper channel setting, the encryption key for each PROSIX sensor, and all other panel programming are stored in AN360 as part of the original panel's "image". When you initiate a panel replacement, you're telling AN360 to send the most recent image taken from the old panel to the new one. By necessity, this process replaces the new panel image you began creating when you started adding PROSIX sensors to the new panel prior to the swap. There is no way to merge these two images together.

If the replacement succeeds, the new panel becomes an exact copy of the last synced version of the old panel. That's the intended result. However, if you enrolled new PROSIX sensors into the replacement panel beforehand, those sensors will be overwritten during the replacement process. If they were powered on and paired for more than 24 hours prior to this, they cannot be factory defaulted and will have to be replaced.

The Most Important Rule

If you are replacing a PROA7 or PROA7PLUS system: DO NOT power up or enroll any new PROSIX sensors before the panel replacement is fully completed.

This includes:

• Door/window sensors
• Motion detectors
• Smoke detectors
• Heat detectors
• Glass breaks
• Key fobs
• Sirens
• Any additional PROSIX device

Leave any new sensors in the box until the replacement process is completely finished.

The Correct Way to Replace a PROA7 or PROA7PLUS

Follow these steps to avoid losing sensors or corrupting system programming:

1. Don't power on the new panel. Leave the new panel powered completely down until you are ready to physically replace the old one. Don't perform any programming on the new panel. If you have gotten to this point and you realize you've made the mistake of powering on the new panel and adding PROSIX Sensors, you should factory reset the new panel, then once all PROSIX sensors have received the reset command, power the panel down completely. You can tell a PROSIX sensor has been released if you open or fault the sensor and the LED begins blinking rapidly. If it's going to be hours or days before you can complete the replacement through AN360, remove the batteries from the new PROSIX sensors to conserve power.

If you happen to be replacing your existing panel with a used PROA7 or PROA7PLUS, be sure the "new" panel has the latest firmware. This ensures compatibility with all sensors. After updating, be sure to perform a factory reset before continuing. To do this, the panel will need to be powered on. As long as you complete these steps, then power back down before the swap is initiated in AN360, you're good. You'll need to work with your alarm dealer to arrange the firmware update, if one is needed.

2. Verify the programming. At this stage, you may want to verify that the "image" of the old panel in AN360 matches the actual programming in the old panel as closely as possible. You'll need to work with your alarm dealer to do this, as end users don't have access to AN360. If the old panel is completely dead, just do your best to complete this step.
3. Perform the panel replacement in AlarmNet360. Provide the MAC and MAC CRC from the new panel to your alarm dealer. They can now initiate the panel replacement process in AlarmNet360. If you plan to reuse the cellular module, PROWIFIZW*, or any other modules from the existing panel, power it down, remove those modules, and NEVER POWER THAT PANEL ON AGAIN WITHIN RANGE OF THE SENSORS unless your alarm dealer tells you to do so.

*When replacing a PRO Series panel paired with Z-Wave devices, AN360 can bring those devices to the new panel, preventing you from having to exclude and then include them again. However, this is only possible when the PROWIFIZW module from the old panel is moved to the new one.

4. Allow the replacement process to finish completely. After the replacement has been initiated in AN360, you should:
   • Power up the new PROA7 or PROA7PLUS.
   • Tap the Setup button for WIFI > choose your SSID > enter your password > Save > Connect.
   • Once connected to WIFI, tap Next, then tap Register.
   • Let the new panel fully sync with AlarmNet360. As it goes through the process of adding the existing PROSIX sensors, the panel will chime for each sensor.
   Do not interrupt this process. Depending on signal strength and the number of enrolled sensors, synchronization may take several minutes to complete. Be sure your alarm dealer also knows not to access the account in AN360 until the replacement process has fully finished.
5. Confirm all existing sensors restored properly. Tap the hamburger menu icon (☰) at the bottom center of the Home screen, then tap Sensors. You should see a list of all enrolled sensors. Verify that the sensor names are correct. To the right of each sensor name, the panel will display the signal strength and battery status of the sensor. Initially, these fields may appear blank. As the panel completes synchronization with the sensors, the signal and battery indicators will gradually populate. The replacement process is not complete until every sensor shows both a valid signal strength and an accurate battery level.

If the old panel was completely dead, or otherwise unable to communicate with the PROSIX sensors for an extended period of time, some sensors may show a low battery condition sooner than expected. PROSIX sensors continuously attempt to check in with the panel. If the panel does not respond, the sensors continue trying repeatedly, which can prematurely drain their batteries. If you suspect that an existing PROSIX sensor may have a dead battery, replace the batteries in the device and make sure it communicates fully with the panel before you enter panel programming.

6. Add new PROSIX sensors. Only after completing the previous steps should you begin enrolling any newly purchased sensors. Once you have verified that all programming has been synced from AN360 to the new panel, you can add additional sensors and make any other necessary changes.

Final Thoughts

We understand why DIY users try to prepare the new panel ahead of time. It feels like the faster and more organized approach. Unfortunately, with PROA7 and PROA7PLUS systems using PROSIX sensors, doing this can actually create major problems during the replacement process.

The safest approach is simple:

• Keep the replacement panel powered off.
• Leave all new PROSIX sensors unopened and unpowered.
• Work with your alarm dealer to complete the AlarmNet360 replacement first.
• Verify old sensors restored correctly.
• Finally, add any new devices and test for proper operation.

Following the proper order prevents lost programming, sensor lockouts, and hours of unnecessary troubleshooting. Alarm Grid customers who need to perform a PROA7, PROA7PLUS, or even VISTAH3 replacement with existing PROSIX sensors should contact support prior to taking any action on the replacement. Our support team is here Monday - Friday from 9:00 AM - 8:00 PM Eastern. You can contact us at 888-818-7728 or by emailing support@alarmgrid.com.

At Alarm Grid, we believe customers should have the freedom to purchase alarm equipment from the source that works best for them. That includes third-party distributors, online marketplaces, and even other end users.

We do not discourage customers from bringing their own equipment. However, it is important to understand that purchasing equipment outside of Alarm Grid can come with certain risks.

One of the most common issues involves used or outdated equipment. While a device may power on and appear functional, it could have hidden problems. Sensors may have reduced battery life, keypads could show excessive wear, and communicators might not perform as expected. In some cases, equipment may be damaged, outdated, or missing critical components.

We have also encountered activation issues with older LTEM-P, LTEM-PX, and IP-COM communicators purchased through third-party sellers. Some older stock did not receive a required critical firmware update and can no longer be serviced. Units with MAC addresses beginning with B82CA0, typically manufactured around 2020 or 2021, and some beginning with 48A2E6, may be affected. Even if these communicators are new in box, they may not be capable of activation.

Another serious concern is account association. Many alarm communicators are registered to an AlarmNet or Alarm.com account. If a used communicator was previously installed and removed during an upgrade, it may automatically attempt to re-register to the original account.

When that happens, the communicator ties back to the previous dealer or seller. If they do not release it, we cannot activate or service the unit. In some cases, the only options are to convince the seller to release the device or purchase a new communicator, which can delay monitoring by days.

Before purchasing from a third party, confirm the seller has a clear return policy. Verify that the communicator firmware is current and that it does not have a B82CA0 or 48A2E6 MAC prefix. Whenever possible, purchase newer equipment from a reputable distributor or retailer.

If you already have a communicator, and you suspect it may be affected by this issue, do not connect it to a wired network before activation. Immediately after powering it up, press and hold the test or registration button for 30 seconds, then release it to default the unit. Completing this step prior to your activation appointment can help prevent registration conflicts.

Ultimately, the simplest way to avoid these issues is to purchase new equipment from a trusted source. When a communicator is purchased through Alarm Grid and found to be defective, we can typically process a replacement in less than 24 hours, helping to minimize downtime.

Alarm Grid is here to support our current and future monitored customers, no matter where you purchase your equipment. We simply want you to begin the process informed and prepared. Our team is available Monday through Friday from 9:00 AM to 8:00 PM. If you have questions, reach out to us by email at support@alarmgrid.com or by phone at 888-818-7728. You can also use the live chat feature available on our website at alarmgrid.com.

Resideo Technologies has announced an automatic firmware update rollout for several AlarmNet LTE communicators used in security systems. These updates are designed to enhance cellular connectivity and ensure a more stable, reliable link between your system and the AlarmNet cellular network.

According to MyWebTech Technical Notification #136, Resideo will begin pushing firmware updates over the air within the next 30 days to select radios used in burglary and residential fire applications. These updates are part of an ongoing effort to maintain optimal performance and address prior cellular connectivity issues.

Affected Radios & Latest Firmware Versions

• Honeywell Home LTE-IV — Firmware 4.1.31.0
• Honeywell Home LTE-IA — Firmware 4.1.31.0
• Honeywell Home LTE-XV — Firmware 4.0.62.0
• Honeywell Home LTE-XA — Firmware 4.0.62.0
• Honeywell Home LTE-L3V — Firmware 4.0.54.0
• Honeywell Home LTE-L3A — Firmware 4.0.54.0
• Honeywell Home LTE-HSV — Firmware 2.14.16

Many of the affected communicators, though still active in the field, have been discontinued by Resideo and AlarmNet. Because they are no longer offered by Alarm Grid, discontinued products are not linked above.

These updates will occur automatically, and no action is required from end users in most cases. However, communicators with low backup battery voltage, or with a missing backup battery, may not successfully complete the update. In those instances, the communicator battery should be replaced so that the update can occur.

A small number of systems may briefly display a “radio trouble” condition when the communicator reboots after the update. This condition can typically be cleared by entering a valid user code + 1 (Off) twice on the system keypad.

Notes on Fire Radios

The same technical notice also reminds users about firmware updates for certain commercial fire communicators (HWF2V-COM, HWF2A-COM, LTE-CFV, LTE-CFA). However, Alarm Grid does not support commercial fire alarm systems, and these devices are not sold or supported by us. If you work with fire alarm communicators, contact your fire system provider or Resideo technical support for further assistance.

Summary

Resideo’s automatic update process ensures continued reliability for AlarmNet-connected communicators. As long as your communicator is in good working order and has adequate power and a good backup battery, it is likely that no action will be required on your part. With a possible exception of a disarm command to clear a communicator trouble display on some VISTA systems.

Alarm Grid will continue to keep you informed of any further changes that may affect system performance or connectivity.