Honeywell Home PROWLTOUCH Posts

Posted By

The Resideo PROINDMV offers a cost-effective alternative to full video monitoring. Up to eight (8) PROINDMV devices can be added to each Total Connect 2.0 account, with no upgrade to full video surveillance required. When activated, the PROINDMV can take a still image or a 10-second clip.


For Alarm Grid customers, any Silver monitoring plan (Self or Full), or higher, can support up to eight (8) of these motion viewers. A Self Bronze plan, can support one (1) PROINDMV. Also, if the panel happens to be set to Local Alarm Mode, then only one (1) motion viewer can be added with clips available locally only. Clips or images captured by the motion viewer can be viewed through the Honeywell Home PROA7PLUS or Resideo PROA7PLUSC panel touchscreen, or through Total Connect 2.0. The PROINDMV is not compatible with the non-plus versions of the ProSeries panels.

In order for the PROINDMV to create a clip or image and send it to the panel and TC2, the panel it's used with must have at least a 15-second burglary communication delay enabled, and the panel must stay in alarm long enough for an alarm report to be triggered. At that point, the clip or image will be sent to the panel and to TC2. In the case of the panel being in Local Alarm Mode, the clip will only be sent to the panel. The motion viewer is never recording unless it has detected an alarm. This means that there is no peek-in feature for the motion viewer. A user can't pull up their TC2 account, choose a PROINDMV device and bring up a real-time image. Hopefully, this may change in future firmware updates.

When the system is armed, and a video or image capture occurs during the Entry Delay period, the motion viewer holds any images or clips until after the Entry Delay has expired. If the system is disarmed before the end of Entry Delay, then any clips or images captured during that time are discarded. If it is not disarmed, then those images or clips will be sent once an alarm report is triggered.

Once the PROINDMV has captured a clip or image, it waits either 1.5 minutes (if there is no activity) or 3 minutes (in the event of constant activity) before it will capture another image or clip. A Maximum of ten (10) captures can occur during an armed period (this is assuming Swinger Suppression is set at the Maximum of 6). I assume this is ten (10) captures per PROINDMV, not per account, but its unclear. I will attempt to confirm this and update this post with that information. When programming, a PROINDMV can be assigned to any active partition. The response types that are available for the motion viewer are Interior Follower or Interior with Delay. So, the PROINDMV will only be active when its partition is armed Away, or Night (assuming the PROINDMV is enabled for Night Stay Mode).

When the panel camera log gets full, once ten (10) captures have been saved, it will begin to overwrite the oldest captures with new ones. All motion viewer captures are purged from the panel log after 30-days. The panel camera log can not be viewed through AlarmNet360, meaning an alarm dealer can't view any potentially private images. Image or clip captures are sent over WIFI (any time its available) or Cellular (if WIFI is down, or not present). Currently, motion captures cannot be viewed through the Honeywell Home PROWLTOUCH or Resideo PROWLTOUCHC.


Tags: , , , , , , , , , , , , , , ,

Comments


Posted By

It's time for ISC West, and all the manufacturers are putting their best foot forward. Resideo now has Release 4 for the ProSeries panels on offer. This update adds Dealer Branding, Customized Voice Descriptors, a WIFI Access Point, 2-Way Voice per Partition, and an Easy Access Help Screen.

Dealer Branding

This can be a hot-button topic for our DIY customers. Many of them don't want dealer branding to mar the look of their touchscreen panel. Release 4 adds the ability to push Dealer Branding to the Honeywell Home PROA7, PROA7PLUS and Resideo PROA7C and PROA7PLUSC. We're not sure how we're going to treat this feature, so stay tuned for more information on this topic.

Customized Voice Descriptors

In the past, Honeywell and now Resideo, and Honeywell Home panels that have supported the voice chime feature were limited to speaking words from a pre-set vocabulary. If a custom voice descriptor was used, then the panel or keypad would just skip that word when speaking the descriptor, as though it didn't exist. With Release 4, this changes for the ProSeries panels. Using either AlarmNet360 or local programming, a custom word descriptor can be entered. It then goes through a text-to-speech process.

If text-to-speech processing occurs on the AlarmNet360 server, then if the custom voice descriptor is typed in by the alarm dealer through AlarmNet360, it will then have to be processed and downloaded to the panel. Then it's ready to be spoken for the zone in question. If the custom voice descriptor is typed in using local panel programming, that means the typed word has to be uploaded, processed, then downloaded again. If processing occurs at the panel, instead of AlarmNet360, then basically the same thing will happen, just in reverse. The point is, some processing and transferring of data must occur, so this kind of change can take a few minutes.

Another very important change comes with this update. In the past, the Device Type has always been spoken as a portion of the zone descriptor (with the exception of Device Type Other). If the Device Type was Window, and you wanted the voice descriptor to be "Front Window" then you only entered "Front" as Zone Descriptor 1 and left Zone Descriptor 2 blank. The panel would automatically say Window as the Device Type. Now, this has changed. The Device Type is no longer being spoken as part of the voice descriptor. So, for my office window, I used Zone Descriptor 1 - Julia, Zone Descriptor 2 - Side, and Device Type Window. However, now, in order to get the panel to actually say "Julia Side Window", I had to make Zone Descriptor 1 - "Julia Side", and Zone Descriptor 2 - "Window". This is a big difference, and may cause some issues, particularly for those with lots of zones. I look for this to possibly change in the near future.

WIFI Access Point

A WIFI Access Point has been added to the ProSeries panels. With this access point the Honeywell Home PROWLTOUCH or Resideo PROWLTOUCHC touchscreen keypad can still be added to a system where no WIFI connection normally exists. This is often an issue seen in second homes, or cabins, where it doesn't make sense to pay for an internet connection when the home is unoccupied. Up to eight (8) secondary keypads can be used per ProSeries panel. Using either the aforementioned touchscreen keypads or the Honeywell Home PROSIXLCDKP push button keypad. As a PROSIX Series Device, the PROSIXLCDKP doesn't require any type of internet connection. It communicates to the panel in the same manner as any PROSIX Series zone does.

Two-Way Voice Per Partition

Two-Way Voice is a feature that allows the central station operator to connect to the location that reported an alarm and either listen in, speak to persons on site, or carry on a two-way conversation. Those, "I've fallen, and I can't get up!" commercials of yesteryear are an early example of two-way voice.

The ProSeries panels have always supported up to four (4) partitions, however, earlier versions did not support two-way voice per partition. When a system with two-way voice enabled reports a burglary or panic signal, the monitoring station receives a special signal. They can then press a command on their end that begins the voice session. Once connected, they can press the 4-Key on their telephone keypad to toggle through up to four (4) touchscreen keypads on the system. Each of those touchscreens can be assigned to any of the partitions that are enabled.

Easy Access Help Screen

In Release 4, a user can go to the hamburger menu icon at the bottom center of the display on either the main panel, or any secondary touchscreen keypad. Once the menu comes up, scroll all the way to the bottom and press Help. A QR Code will be displayed. Scan the QR code with your smartphone or tablet, and then press "Youtube" and you'll be taken to the Resideo and Honeywell Home ProSeries channel on Youtube. You can then browse through the help topics for a video that addresses your issue.


Tags: , , , , , , , , , , , , , ,

Comments


Posted By

In a previous Beta Firmware Version available to industry insiders, Resideo introduced the ability to live-stream SkyBell Doorbell Cameras from the Honeywell Home ROA7PLUS and Resideo PROA7PLUSC. The new upcoming feature will likely be made available to the general public very soon.

We have known about the camera streaming capabilities for the PROA7PLUS for quite some time, but we had yet to see what form the feature would take. That changes with this beta release, as we now have our first glimpse at the feature. Users can live-stream any Total Connect 2.0 compatible SkyBell device right from their PROA7PLUS or PROA7PLUSC. Compatible doorbell cameras include the round Honeywell SkyBell DBCAM and the slimline Honeywell SkyBell DBCAM-TRIM. The round model has since been discontinued, but the slimline model remains available for purchase from the Alarm Grid website.


In addition to streaming from a compatible panel, the system will also display a message whenever someone is at your door and rings the SkyBell device. The camera streaming also includes audio streaming, and you can engage in a two-way voice conversation with the person at your door. This is thanks to the integrated microphone included in the ProSeries Security Systems. This is great for telling your friend that you will unlock the door for them, or for telling a solicitor that you're not interested. The possibilities will be endless!

And not only is this feature available for the PROA7PLUS and PROA7PLUSC, you can also stream from the compatible touchscreen keypads, those being the Honeywell Home PROWLTOUCH Keypad and the Resideo PROWLTOUCHC Keypad. The touchscreen keypads support all of the same capabilities as the panels in this aspect, including doorbell camera streaming, audio streaming, and two-way voice. Remember that you must have WIFI capability enabled on the panel to integrate the touchscreen keypads as well as the Skybell.


One very important note about the SkyBell streaming feature is that it is only going to be supported by the "PLUS" versions of the ProSeries Panels, those being the PROA7PLUS and the PROA7PLUSC. It is our understanding that the PROA7 and PROA7C will not support the feature. If you were trying to decide between a "PLUS" and a "non-PLUS" version of a ProSeries System, well this is yet another reason to spring for one of the higher-end versions!

Although the feature has not been released to the public quite yet, we still have a general idea of how SkyBell Camera streaming will be implemented. First, you must have the system monitored and set up for service with Total Connect 2.0. You will then need to link your SkyBell device with your Total Connect 2.0 account. If you intend on buying a new SkyBell Camera for this purpose, then make sure that you are getting one of the Honeywell models for use with Total Connect 2.0. A user should never attempt to pair an Alarm.com SkyBell device with TC2 or with the native SkyBell App. After you link your ProSeries System with TC2, there will be a new Cameras option inside the main system menu. It is there that you can choose to stream a SkyBell Camera linked with your TC2 account. The device should show up after the doorbell camera has been successfully integrated with your TC2 account, and the panel has properly refreshed with the AlarmNet Servers.

We know that many Alarm Grid users will certainly take advantage of this feature once it is released. To ensure that you can get started with SkyBell Camera streaming as soon as it becomes available, make sure that you are monitored ahead of time. All TC2 users are entitled to have up to five (5) SkyBell devices linked with their accounts. You don't even need a true video monitoring plan to get started. More information on the subject can be found in this FAQ. If you're interested in signing up for monitoring service, and you haven't decided on a service provider as of yet, then you could consider one of Alarm Grid's monitoring plans. If you have questions, reach out to us by emailing support@alarmgrid.com. Remember that we check and reply to emails during our usual business hours of 9am to 8pm ET M-F.

Are you excited about SkyBell Doorbell Camera streaming for the PROA7PLUS, PROA7PLUSC? We're sorry to tease you with a feature that hasn't seen its official release quite yet, but we figured that it would be okay to build up some hype. With the SkyBell Camera Streaming and Local End-User Programming for the ProSeries Panels both in Beta Development, it's fair to expect the features to be fully released any time now. We will provide updates in the Alarm Grid Blog regarding any major releases. For now, make sure to comment down below to share your thoughts on this upcoming feature. Also feel free to let us know about any security system coverage you would like to see us focus on in the future. That's it for today's blog, stay tuned for more Alarm Grid content coming soon!

Tags: , , , , , , , , , , , , , , , ,

Comments