2GIG Edge AT&T LTE 3-1 Wireless Kit Posts

2GIG has announced the release of their first big firmware update for the 2GIG Edge. This update adds support for image sensors in the form of the 2GIG-IMAGE3. In order to support image sensors, the 2GIG XCVR3-GC3 must be installed. Image sensors can be used without losing any other features.

The 2GIG Edge is a great addition to the 2GIG panel lineup. It has built-in facial recognition, Z-Wave Plus V2 (700 Series) support, up to four (4) Smart Area partitions, Bluetooth disarming, and so much more. One of the disappointing aspects of the panel rollout, is that it didn't support image sensors at the time of its release. That problem is now rectified with the new 3.1.0.011 firmware.

If you have a 2GIG Edge, then there are a couple of ways that you can get your panel updated. Alarm.com is still in the testing phase with this firmware, so it can't be pushed remotely quite yet, but remote over-the-air (OTA) updates will be available soon. Once this form of upgrade is available, you'll need to request the update from your alarm dealer. If your panel has a WIFI connection, the update will be completely free. If your panel connects to Alarm.com via cellular only, then a small fee will be incurred when updating OTA.

If you're an Alarm Grid monitoring customer, you can request the upgrade by emailing support@alarmgrid.com. Once the update is available, we'll verify the cost, if any, and if you give the go ahead, we'll push the update to your panel, and pass the cost along to you on your next monthly monitoring bill, with no markup. Remember, there will only be a fee if your panel connects to Alarm.com via cellular only. The cost for this type of update varies, depending on the size of the file to be downloaded. It could be as little as fifty-cents, or as much as a few dollars.

The other way that your panel can be updated is via USB. There is a USB port on the top of the 2GIG Edge. You can download the firmware update files from Alarm Grid here. This is a free download. Use a standard USB drive with at least 1GB capacity, and not more than 16GB capacity. Be sure the drive is formatted using FAT32, and that it has only one (1) partition. The file you download should be saved to the root directory of the USB drive. Full instructions for downloading and upgrading can be found here.

Once the file has been downloaded to the USB drive, remove the drive and take it to the 2GIG Edge panel. The USB port is on top of the panel, covered by a rubber boot. Remove the boot, and insert the drive. A message should appear on the panel, letting you know that an update is available. Press "Update", enter either the Installer Code (default 1561) or Master Code (1111) and the update will then proceed. Be sure the panel has AC power, and that AC power is not interrupted during the update process. The panel will reboot and provide a message letting you know when the update is complete. Remove the USB drive and reinsert the rubber boot.

If you have a 2GIG Edge Remote Keypad, it will be updated by the 2GIG Edge panel, once the panel has completed updating. Be sure the keypad has AC power and that it is connected to WIFI and to the Edge panel. You can verify this by making sure the keypad shows the panel home screen, and the proper panel status. Once the panel has been updated, it should automatically update the keypad. Again, once the firmware has been installed, the keypad will reboot to complete the update process.

In addition to support for image sensors, this firmware also corrects a few known issues regarding WIFI connection problems, and both remote keypad and main panel touchscreen issues. You can read the full firmware Release Notes Here.

So, what do you think about this firmware update? Do you have a 2GIG Edge and want to share your experience with it? Have you been anxiously awaiting image sensor support? Leave a comment below and let us know your thoughts. We always look forward to hearing from you.

We want to inform 2GIG Edge users, especially those who may install their own system, to a special warning put out by 2GIG. The warning identifies a potential wiring mistake that could result in permanent damage to the 2GIG Edge Alarm Panel. The entire warning put out by 2GIG can be seen here.

The 2GIG Edge receives primary power from the 2GIG AC1 Plug-In Transformer. This transformer is rated at 14VDC, 1.7A. You must add your own alarm wire to complete the connection. Since DC power is being used, proper polarity must be observed, both at the transformer and at the panel. At the transformer, the red wire should connect to positive (+) terminal, and the black wire should connect to the negative (-) terminal.

Then, at the panel, the red wire for positive (+) power should connect to the DC IN+ terminal. The black wire for negative (-) power should connect to the DC IN- Terminal. Or alternatively, if you are using a Honeywell LT-Cable, then you can simply plug the barrel connector in the DC IN Barrel Port. Following this process correctly will help ensure that you do not accidentally damage your 2GIG Edge.

Where the concern arises is that there are actually two (2) sets of terminal blocks on the 2GIG Edge Panel for connecting wires. And unfortunately, 2GIG didn't exactly make it super clear as to which set of labels goes with which terminal block. The best way to figure it out is in the fact that one set of terminal blocks is shorter than the other terminal block set. The set for providing power is the smaller terminal block with six (6) terminals, not the larger terminal block set with eight (8) terminals. You can see this in the image above.

The DC IN+ and DC IN- Terminals, along with the DC IN Barrel Port, are identified as the Power In Terminals. Those are the ports you want to use when providing power, whether you are using traditional alarm wire and you use DC IN+ and DC IN- (making sure to observe polarity) or you have a Honeywell LT-Cable and simply plug into the DC IN Barrel Port. If you do use DC IN+ and DC IN-, then make absolutely sure you are connecting to the terminal block with only six (6) terminals.

The potential problem arises in the other, larger terminal block with eight (8) terminals. This is known as the DCOUT+ Terminal Bock. And to make matters confusing the top two (2) wire terminals on this set have names that may make you think they are used for providing primary power to the system. But in reality, connecting primary system power here could seriously damage the system. These two (2) misleading wire terminals are labeled GND and AUX+, but these are output terminals.

Simply put, you do NOT want to use these terminals for providing system power. Again, the easiest way to avoid doing this is to make sure you are using the smaller terminal block with only six (6) wire terminals, NOT the larger terminal block with eight (8) wire terminals. Of course, if you use a Honeywell LT-Cable and the panel's DC IN Barrel Port, then this isn't really a potential hazard. There is only one barrel port and no way to mix it up.

The lesson of the day here is to be very careful when you are connecting power wires to the 2GIG Edge. Use the DC IN+ and DC IN- Terminals on the smaller block with six (6) terminals. The red positive (+) wire should go to DC IN+, and the black negative (-) wire should go to DC IN-. Or use a Honeywell LT-Cable and the DC IN Barrel Port. Do NOT use the GND and AUX+ Terminals on the larger block with eight (8) terminals. Making that mistake could potentially damage your 2GIG Edge System. Always be safe and smart, and make the correct wiring connections!

If you have any thoughts on the 2GIG Edge, or if you have any personal experience in wiring the system for power, then please feel free to share what you would like in a comment down below. We would love to hear from you! And remember to stay tuned to the Alarm Grid Blog for more tips and security news coming soon.

We have a relatively short post today, as we just wanted to say "Thank You" to 2GIG for featuring Alarm Grid on the 2GIG Instagram Page, @2gigsecurity. 2GIG posted our unboxing video of the new 2GIG Edge Security System. Thank you 2GIG, we're glad that you liked our unboxing video!

The 2GIG Edge is a wireless all-in-one alarm panel with a 7-inch touchscreen controller, built-in WIFI and LTE cellular, an integrated Z-Wave Plus V2 700-Series controller, support for up to 100 wireless zones, facial recognition disarming, Smart Area Partitions, optional Bluetooth disarming, full connectivity with the Alarm.com platform, and so much more! The system is available now on the Alarm Grid website in standalone AT&T and Verizon variants, or in one of our complete security system starter kits that include everything you need for alarm monitoring!

The unboxing video that 2GIG reposted is one of our very first in a new series by Alarm Grid, where "James the Video Guy" unboxes various alarm control panels and security system kits to show you exactly what's inside and what comes included. While James is usually known for his work behind the camera, this new series has given him a chance to step into the spotlight and showcase some of the most popular products offered by Alarm Grid. You can see the full 2GIG Edge Unboxing Video down below. We also made a blog post about our new unboxing videos back in April, which you can view here.

Thanks again to 2GIG for featuring us on their Instagram page. If you have any requests for what you would like to see in a future unboxing video from Alarm Grid, please let us know. You can leave a comment down below to make your request. We hope to have more videos like this available in the future. We will be sure to let you know as they come out. You can also leave a comment below to share your thoughts on our unboxing videos or any other videos featured on the Alarm Grid YouTube Channel. Thanks for reading, and we'll be back with more great security system content coming soon!

A new alarm panel hitting the market often means an old one is discontinued. That is the case here today, as the 2GIG GC3e has been formally discontinued by Nortek Control. The GC3e has been replaced by the 2GIG Edge, which is available in both an AT&T variant and a Verizon variant.

As we look back on the 2GIG GC3e, we gotta admit that the panel was in an unfavorable position from the start. The system was a direct replacement to the 2GIG GC3, as it retained largely the same user interface, and its design only received a minor refresh. The big new addition with the GC3e was its ability to support 2GIG eSeries Encrypted Sensors. Along with the 2GIG GC2e, this marked the first time that 2GIG Alarm Panels could support encrypted sensors.

Unfortunately, 2GIG was late to the party, as other security systems like the Honeywell Lyric and Qolsys IQ Panel 2 Plus already had encrypted sensor support, not to mention a wide selection of sensors to choose from. Coupled with the fact that Qolsys continued to release new features for the IQ2+, and Resideo (formerly Honeywell) had the PROA7PLUS on the way, it quickly became clear that 2GIG would need to do better in order to keep up.

Thus began development on the 2GIG Edge. We first learned about the system in October of last year. With a bold new website and heavy promotion, hype around the Edge grew quickly. But this also brought questions in the back of our minds - what would happen to the GC2e and the GC3e? These panels had been on the market for less than two (2) years. Would 2GIG really abandon them so quickly? Well, today we have the verdict. The 2GIG GC2e stays, and the 2GIG GC3e heads off to the old alarm system graveyard in the sky.

First released in late July 2019, the 2GIG GC3e became known for its strong build quality and stark similarities to its GC3 predecessor. But it had a hard time competing with fellow Alarm.com Security System, the Qolsys IQ Panel 2 Plus. Buyers continued to flock to the IQ2+, which offered Automatic Bluetooth Disarming and Facial Recognition. Those features could not be easily added to the GC3e, so 2GIG decided to cut their losses and add those features into a new alarm panel, the 2GIG Edge. 2GIG even one-upped Qolsys by making it so that the Edge's Facial Recognition feature can be used for disarming the system!

With the Edge firmly in place as 2GIG's new flagship panel, and the 2GIG GC2e set as their "budget-friendly" option, some wondered if the 2GIG GC3e might be kept in production as a sort of "middle-of-the-road" offering. But nope, apparently, three panels is too many at 2GIG, and it's the GC3e biting the dust. And now, less than two years after hitting the market, and barely more than two years removed from its unveiling at ISC West 2019, we are saying goodbye to the 2GIG GC3e. It wasn't a long ride, but it was a good one.

If you have an existing 2GIG GC3e, then don't worry! The system will continue to be supported for alarm monitoring and service with the Alarm.com platform. Given the system's great build quality, it's fair to expect that existing GC3e Panels already out in the field will likely stay in service for quite some time, probably for the duration of LTE cellular networks. And speaking of LTE communication, Alarm Grid is continuing to offer LTE communicators for the 2GIG GC3 and 2GIG GC3e. These are the 2GIG LTEA-A-GC3 (AT&T LTE) and the 2GIG LTEV1-A-GC3 (Verizon LTE). If you need to get your GC3 updated, or your GC3e monitored, then either one of these modules is an excellent option. They're super easy to install, and they provide ultra-reliable cellular connectivity for the peace of mind that you deserve.

Meanwhile, the 2GIG GC2e will remain in production as the company's budget panel. However, we don't usually recommend that system for alarm monitoring, as it has no internet connectivity option to serve as an additional communication path, and it is relatively bare-bones in terms of features. But it is still an available option, and many users find that the GC2e is a strong offering as a replacement for the 2GIG GC2 or as a non-monitored system serving as a local noisemaker.

But for our top 2GIG pick, it should come as no surprise that we are recommending the new 2GIG Edge Alarm System. With its great features like 7-inch touchscreen controller, Facial Recognition, optional Automatic Bluetooth Disarming, Smart Area Partitioning support, 700-Series Z-Wave Plus V2 Smart Home Automation, and being dual-path ready right out of the box, we are proud to say that this system is available now on the Alarm Grid website. While we might miss the 2GIG GC3e, the 2GIG Edge certainly fills the void. Time will tell how the Edge fares against other competing systems like the Qolsys IQ Panel 2 Plus and Honeywell Home PROA7PLUS.

What do you think of the 2GIG GC3e? Will you miss the system? Are you surprised to see 2GIG discontinue the system after less than two years? Did you ever get to try the system out for yourself? Share your thoughts and experiences in a comment down below. We would love to hear what you have to say. And remember to stay tuned to the Alarm Grid Blog for more security system content coming soon. We promise, we don't discontinue systems every day, but when we do, we always make sure to say a proper goodbye. Farewell 2GIG GC3e!

With the 2GIG Edge now available, users have access to some features we have never seen before in home security. One feature that really stands out is the system's facial recognition capabilities. This is the first ever panel from Alarm Grid to support facial recognition disarming!

The 2GIG Edge facial recognition feature is set up when you go to configure a user for the system. You can also configure it for the Master User, which is likely what you will want to do, along with changing the code away from its default of 1111. This is probably one of the first things you will do after getting the 2GIG Edge Security System, so consider this to be a bit of a starter's guide as well.

And don't forget that the feature is totally optional to use. If you don't want your 2GIG Edge System storing your "facial biometrics", then you don't have to. But if you do decide to set up the feature, we'll tell you right away, it works very well, and it's super convenient. It is also important to mention that all facial biometric information is only stored locally at the panel. This information is neither shared nor stored with Alarm.com in any fashion. Up to ten (10) users on a single 2GIG Edge Panel can be set up with the Facial Recognition feature, so do keep that in mind if you have a large number of users set up with your 2GIG Edge. But with that of the way, let's get started setting up the Facial Recognition feature on the 2GIG Edge!

What you need to do is access the User's Menu. Begin by clicking the Settings Icon (the gear) in the bottom-right corner. Then provide the Master Code (default 1111) or the Installer Code (default 1561). Then choose Users. And just like that, you are in the Users Menu.

You can click the Add User button in the bottom-right corner to create a new user. But if you haven't configured the Master User yet, then that's what you should do first. To configure the Master User, just click on the pencil icon next to it. You will be taken to the menu where you can adjust a variety of different settings.

From here, you can set a custom Display Name if you want a more personalized touch than "Master User". But today, we're going to focus on the facial recognition feature. You can see that it is disabled by default, so you should go and enable it by setting the toggle bar to green. And once you do, you will be greeted by the Facial Recognition Disclaimer Screen. Read through it, and assuming you agree, then click the Agree button in the bottom-right. You have to scroll all the way through it, or else you won't be able to click the Agree button, as it won't be illuminated.

Then you will need to capture your facial profile. You start by pressing the Begin button. You will need to position your head into the outlined box. Then once it recognizes your face, the outline will turn green. You will be asked to look to the right, and it will detect the movement. Then you will be asked to look to the left. Again, the movement will be detected. Oh, and when you go to do this yourself on your own 2GIG Edge, you don't need to have your phone in the photo. I was just trying (with varying degrees of success) to capture the moment in a series of photos. If you just complete the process normally as 2GIG intended, it's very easy.

You want to be very careful when capturing your facial profile - definitely more careful than me trying to pull double-duty by trying to take photos of the process at the same time! Make sure your face fits as nicely in the outline as possible. Feel free to move your head closer or further away from the panel if you need to. Then, when asked, turn slightly to the right, and then slightly to the left, and you will be all done! It only takes a matter of seconds. You will get the "Congratulations" message, and the feature will be in effect. And if you feel concerned that maybe you did a shoddy job, you can always reconfigure your 2GIG Edge Facial Profile later on. If you find that the system is having a tough time recognizing your face, then repeating this process (and doing it carefully) can make all the difference.

Once you click Next, you will be taken to a screen where you can choose to watch a tutorial video about how the Edge uses facial recognition. It may be helpful for you to get the very most out of the feature. Or you can skip it if you feel like this guide is sufficient. But you will still need to take an "Avatar" photo. Again, I'm a one-man team, so I tried to take a photo of myself trying to take a photo of myself (I never thought I'd write that sentence). Considering the circumstances, I think my "Avatar" turned out pretty nice!

If you're satisfied with your appearance, you can choose Use This Image. Or if you're a perfectionist, feel free to Retake Photo. If you decide that you can't take a good photo to save your life, then you can choose to Skip the step. But after that, facial recognition will be ready to go. If you did this for the Master User, you can even use facial recognition to get into Master-level programming. Whenever the system needs a code, the panel camera will activate. You just position your head, look left and right (like you're suspicious), and you will get in. Now the real question - can I take a photo of myself passing a facial recognition test?

Disclaimer - I cheated. That shot above is actually a video frame. The "User Master User Recognized" message only appears on the screen for a split-second, much too fast for an amateur self-cameraman like me to take a proper photo. But let's focus on what really matters here. This feature actually works VERY well. You can see it recognized me quite easily. And don't worry about it being a security risk. NOBODY else in the Alarm Grid Office could disarm with my facial profile. We had someone else try. They don't have the same "facial profile" as me, so the Edge wouldn't acknowledge them. But my face is able to trigger it quite easily.

You can use facial recognition to arm, disarm, and even enter into Master-level programming when a code is needed. Just be careful to set up your "facial profile" properly, and the 2GIG Edge will take care of the rest. If you have any thoughts on the feature, please share them down below in a comment. And stay tuned for more content from Alarm Grid coming soon!

After much anticipation and speculation, the 2GIG Edge Alarm System is finally here! We have the Edge Panel available in two (2) cellular communicator options (AT&T or Verizon), plus complete 2GIG Edge System Kits, and various alarm system accessories exclusively for use with the Edge.

If you have been keeping up with the Alarm Grid blog, then you probably already know that the Edge is perhaps the single most highly anticipated thing we have ever seen out of Nortek Control and 2GIG. The state-of-the-art wireless all-in-one (AiO) panel retains virtually all of the same great features and capabilities of the 2GIG GC3e System that came before it, including a 7-inch LCD touchscreen for easy and seamless navigation, 100 wireless zones, support for 2GIG eSeries Encrypted Sensors, and legacy 345 MHz sensors (both Honeywell 5800 and 2GIG 345 MHz), the ability to build and customize up to four (4) individually controlled and operated Smart Area Partitions, One-Touch Arming, Chime & Voice functionality, Alarm.com connectivity, a digital slideshow picture frame, and much more.

But what makes the 2GIG Edge different and unique is its new features. First of all, the Edge has a completely refreshed design for a 2GIG Panel, as it is the first system from 2GIG to break away from the traditional all-white panel. Instead, the Edge comes in a black design that looks impressively modern and fits in nicely with almost any setting. We're also pleased to say that 2GIG was able to fit more hardware into the Edge Panel, putting it in on par with the Qolsys IQ Panel 2+ panels. This includes a built-in glass break detector, a front panel camera that offers facial recognition, and an 85 dB sounder for alarm events.

One noteworthy difference with regard to 2GIG Edge facial recognition is that it can be used for automatically arming and disarming the system upon detecting the user's face, which is not possible on the IQ Panel 2 Plus. Other familiar IQ2+ features also offered with the Edge include optional automatic Bluetooth disarming for your phone, panel live-streaming for compatible Alarm.com Cameras, and full connectivity with the Alarm.com security and automation platform.

Perhaps one of the most important aspects of the 2GIG Edge is the fact that it has a built-in LTE cellular communicator. This is used for connecting the system with Alarm.com, since ADC requires that all systems using their services have an active cellular communication path. This is in addition to the internal WIFI card for the 2GIG Edge that is also used for communicating with Alarm.com. Using cellular and internet communication together on a security system is often referred to as dual-path connectivity, and it is great because it helps to ensure that the system stays monitored during any type of communication outage. But while internet connectivity is technically optional, cellular communication is required. This means that you will need a monitoring plan that includes cellular communication to get the 2GIG Edge monitored. Some monitoring plans you may consider include the Gold and Platinum Level Plans from Alarm Grid (Self or Full). You can learn all about Alarm Grid monitoring plans in this comprehensive blog post.

As we mentioned before, the cellular communicator for the 2GIG Edge is built into the panel. While this might seem like a positive attribute, it is a bit of a double-EDGEd sword when you consider the issue more closely. On one hand, this means that there is no need to purchase a separate communicator for the 2GIG Edge. Everything needed for the system to connect with Alarm.com is built into the panel. But this also means that if something ever goes wrong with the communicator, then it will be necessary to replace the entire panel, rather than just simply swapping out the communicator. The same is true for the system's WIFI card. If it is damaged, then a completely new system is needed. There is also no word on how a built-in LTE cellular communicator will affect the system in the very distant future when LTE will inevitably face its own sunset. Fortunately, this is unlikely to be a concern for at least 15 to 20 years. We've also seen the Qolsys IQ Panel 2 Plus experience tremendous success while also opting for an integrated, irreplaceable LTE cellular communicator and WIFI card, so there's a good chance that the Edge will end up being just as successful. But we do want to give recognition to Resideo and their PROA7PLUS System for having the foresight to use fully replaceable LTE cellular radios (AT&T or Verizon), plus fully replaceable WIFI modules.

One thing new to the Edge that we have never seen on any other alarm control panel before is a 700-Series Z-Wave Controller. Also known as Z-Wave Plus Version 2, the 700-Series of Z-Wave Smart Home Automation promises significantly better wireless range and battery life, as well as much stronger wireless security when compared with previous iterations of Z-Wave technology. Although we haven't seen many 700-Series Z-wave devices hit the market just yet, it is worth mentioning that 2GIG recently released their own Z-Wave 700-Series Smart Thermostat, the 2GIG STZ-1. This smart thermostat can make a great addition to your new 2GIG Edge System and the automation network you plan to build around it. Remember that we have all sorts of Z-Wave lights and Z-Wave door locks available on our site for you to construct a complete smart home to make your life easier. But if you want to hold out a bit longer for the 700-Series Z-wave devices that will inevitably make their way to the marketplace sooner rather than later, then we don't blame you at all. And as you may have guessed, every Z-Wave home automation device that you pair locally with the 2GIG Edge will also be accessible remotely through Alarm.com once you get the system monitored with a plan that includes remote access.

With all of the introduction and explanation out of the way, let's take a look at the new products. First up is the base 2GIG Edge Panel, available in AT&T LTE and Verizon LTE:

• 2GIG Edge System w/ AT&T LTE
• 2GIG Edge System w/ Verizon LTE

If you are starting from scratch, then you might prefer to purchase one of our 2GIG Edge Starter Kits, which also include some sensors for you to pair with the system, as well as a Honeywell LT-Cable for easily powering the system. You can choose whether you want a fully encrypted kit with only encrypted sensors or a standard wireless kit, where the included door and window sensors don't utilize wireless encryption. Keep in mind that you can always upgrade to encrypted sensors later if you start out with a non-encrypted system. And also remember that you will need to decide whether you want your 2GIG Edge System to have an AT&T LTE Communicator or a Verizon LTE Communicator. This may be the most important consideration prior to purchase since the LTE communicator can't be replaced. Be sure to check coverage maps for the area where the panel will be used, and choose whichever carrier will have the best signal in the area.

Our system kits come in two (2) sizes. First, we will look at the 3-1 Edge System Kits that include three (3) wireless door and window sensors, and one (1) wireless motion detection sensor. These 3-1 Kits are best-suited for use in a smaller home or an apartment. Here are our 2GIG Edge 3-1 System Kits:

• 2GIG Edge 3-1 Kit w/ AT&T LTE
• 2GIG Edge 3-1 Kit w/ Verizon LTE
• 2GIG Edge 3-1 Encrypted Kit w/ AT&T LTE
• 2GIG Edge 3-1 Encrypted Kit w/ Verizon LTE

We also have our 10-1 Edge System Kits that come with ten (10) door and window alarm sensors, and one (1) motion sensor. This size kit is best used for a larger home or a small business. Again, the same equivalents apply to this size, so you have four (4) possible kits to choose from. Here are the 2GIG Edge 10-1 System Kits from Alarm Grid:

• 2GIG Edge 10-1 Kit w/ AT&T LTE
• 2GIG Edge 10-1 Kit w/ Verizon LTE
• 2GIG Edge 10-1 Encrypted Kit w/ AT&T LTE
• 2GIG Edge 10-1 Encrypted Kit w/ Verizon LTE

Lastly, we want to check out the system accessories for the 2GIG Edge. There are a few usual suspects here, including a replacement transformer and a replacement backup battery, plus a specially prepared power cord released by 2GIG. But we think the most interesting accessory is the wireless touchscreen keypad built exclusively for use with the 2GIG Edge Alarm System. Again in a similar fashion to the IQ Panel 2 Plus, the 2GIG Edge Remote Keypad mimics the system's display and can perform virtually any system function, much like the IQ Remote. But unlike Qolsys and the IQ Remote, 2GIG has made their remote keypad with an end-user replaceable battery, which is a huge improvement in our eyes.

Here are the 2GIG Edge System Accessories:

• 2GIG AC1 Replacement Transformer
• 2GIG Edge 24+ Hour Backup Battery
• 2GIG Edge Prepared Cable w/ AC1 Barrel Connection
• 2GIG Edge Remote Keypad w/ Touchscreen Controls
• 2GIG Edge Remote Keypad Backup Battery

One final note about the 2GIG Edge is that there has been no indication that 2GIG intends to release a new "exclusive" sensor lineup for use with the system. Historically, this is a bit unusual, as you traditionally see a new security system (especially one as heavily promoted and anticipated as the 2GIG Edge) released alongside a new lineup of sensors designed specifically to accompany the system. Even the last major releases from 2GIG saw this, as the 2GIG GC2e and 2GIG GC3e became synonymous with the encrypted 2GIG eSeries Sensors. We only mention this because it's likely that some users out there will be actively looking for sensors to add to their new 2GIG Edge System, and they may be surprised to learn that there is no special 2GIG Edge Sensor Family. However, you still have a plethora of great sensor options to choose from, as the 2GIG Edge thrives in terms of backward compatibility. As we mentioned earlier, the system supports encrypted sensors from the 2GIG eSeries Lineup, plus non-encrypted Honeywell 5800 Sensors (uni-directional only) and 2GIG 345 MHz Sensors. If you are looking to expand upon your 2GIG Edge Alarm System, then those three (3) sensor families give you some awesome options to choose from!

The 2GIG Edge System, our 2GIG Edge System Kits, and the 2GIG Edge Accessories are all available now, and they can be purchased from the Alarm Grid website. Do you have any thoughts or questions about the 2GIG Edge? Leave them down below as a comment. We would love to get some discussions started on this super exciting new security system. Do you think the 2GIG Edge has what it takes to compete with strong systems like the Qolsys IQ Panel 2 Plus and Resideo PROA7PLUS? What aspect of the 2GIG Edge has you the most excited? Is there anything you would like to see in a future firmware update or patch for the Edge? Get the discussions started down below, as we look forward to hearing from you. And stay tuned to our blog for more security system news coming soon!