Press Releases Posts

Johnson Controls released a Technical Advisory Bulletin on Monday noting that some PowerSeries Neo, Pro LTE, and Internet Dual-Path Communicators have labeling errors. The serial number on the box appears to be incorrect. Comms built between August 15, 2021, and July 29, 2022, are affected.

The model numbers affected are the DSC TL880LECVZ, TL880LECAT, TL880LEBAT, TL880LEBTL, and TL880LECTL. This is a labeling error only and does not affect the signal transmitting, or Alarm.com remote control capabilities of these communicators in any way. The mixup seems to be with the name on the label on the product, and the serial number on the label on the box.

The model name listed on the label of the product is incorrect, while the serial number listed on this label is accurate. The model name listed on the sticker for the box is correct, but the serial number listed on the box is incorrect. So, be sure when registering one of these units that you use the serial number from the sticker for the product and not the one from the box.

The following products, built during the listed date range, are affected:

Beginning July 29, 2022, new, updated and correct labels should be placed on these products. Remember, the performance of communicators that were manufactured during this timeframe is not compromised. This is only a labeling error, so as long as the serial number taken from the sticker affixed to the product itself, or the IMEI number from the printed circuit board is used everything should work as intended. DSC offers a handy Date Code Lookup tool at this site. You can find information on looking up a date code for any DSC product on that page.

The fact that this issue wasn't discovered sooner seems to indicate that this is a very minor issue. What do you think about this announcement? Do you often use these communicators? Have you run across this issue? Leave us a comment below and tell us what you think. We always enjoy hearing from our readers. That's all for today, until we meet again, stay safe!

Resideo announced last week that due to a required component becoming obsolete, they are forced to discontinue the popular 5800FLOOD sensor. There is still some available stock, so Alarm Grid has not yet discontinued it, but once all stock has been exhausted, the 5800FLOOD is gone for good.

The 5800FLOOD is popular because unlike the 5821, it doesn't require that a water probe be added to the sensor. Water detection is built-in, and configuration is easy. Another benefit of the 5800FLOOD is that it will alert for flooding more quickly than the 5821. The prongs of the 5800FLOOD need only be in contact with water for about 25 seconds before a signal is sent to the alarm panel. The 5821 flood probe must be in contact with water for about three (3) minutes before sending a signal.

In addition to flood sensing, the 5800FLOOD also monitors for extreme cold and/or hot temperatures locally. This is done using a temperature sensor that is built into the 5800FLOOD. For cold temperature sensing, if the ambient temperature drops below 45℉ (7.2℃) for more than 15 minutes, an alert is sent using Loop 1. For high-temperature sensing, if the temperature rises above 95℉ (35℃) for more than 15 minutes, then an alert is sent using Loop 2. The flood sensor transmits using Loop 3.

Now that the 5800FLOOD is being discontinued, the Resideo and Honeywell Home 5821 is the recommended replacement. One drawback to the 5821 is that it requires a remote probe be added for flood sensing, and for freeze sensing. However, only one (1) remote probe can be used per transmitter, so if you need to monitor for both flood and freeze, two (2) 5821s are required.

The 5821 supports the following functions:

For flood sensing, we recommend using the FP280 as it includes wiring, and the required resistor is already in place. With the 470PB, the user is responsible for providing their own wire and must add the 2.2 MΩ resistor themselves. In all cases, wiring between the 5821 and whichever remote probe is used should be made as short as possible, and should not exceed 96" (243cm). Be sure to read the full Install Guide for the 5821 for all of its various quirks.

Supply chain shortages claim another victim in the 5800FLOOD. It seems like only yesterday that we were excitedly telling you about it. What are your thoughts on the demise of this "New and Improved" environmental sensor? Leave us a note in the comments, as we always love hearing from our readers.

Today is Alarm Grid's birthday! We're ten years old today. Wow, how time flies. We've weathered lots of things in our ten years. Hurricanes and pandemics just to name a few. To celebrate our special day, we will be closing early today. Our phones are off as of 12:00 pm Eastern Time.

As is always the case, our central station partners are available around the clock, every day. All signals sent by your Alarm Grid monitored alarm system will be handled in the usual manner. If you need to contact the central monitoring station, either to cancel a false alarm or to verify a signal, customers in the United States can contact Criticom Monitoring Services (CMS) by dialing (888) 818-7728 and choosing Option [9].

Canadian customers can contact Rapid Response at (800) 932-3822. Remember any time you contact either monitoring station, you will need to provide your name, your address, and your false alarm password or phrase. If you provide incorrect information when asked it will result in the dispatch of authorities.

If you have a support question about your alarm system or need to make changes to your account, you need to speak with one of our technicians. For those types of requests, send an email to support@alarmgrid.com with as many details as possible about what type of assistance you need. Remember that when we return tomorrow, there may be a tiny support backlog. Please be patient and we will work through all requests as quickly as possible.

I hope you'll join me in wishing a Happy Tenth Birthday to Alarm Grid. We set out to disrupt the traditional alarm equipment and monitoring model, and I think we've accomplished that. It is our strong belief that everyone should have access to professional quality alarm equipment and that you shouldn't have to pay someone else to do what you can do yourself. We've been working toward that end for a decade now. Happy Birthday to Alarm Grid, and many more!!

Our offices will be closed on Monday, July 4, 2022 in observance of Independence Day. On this day in 1776, our founders declared our independence from England by formally adopting the Declaration of Independence. Since then, July 4 has become a day to celebrate family and freedom in America.

Our central station partners are available around the clock, every day. All signals sent by your Alarm Grid monitored alarm system will be handled in the usual manner during the holiday unless you've made previous arrangements with us. If you need to contact the central monitoring station, to cancel a false alarm or to verify a signal, customers in the US can contact Criticom Monitoring Services (CMS) by dialing (888) 818-7728 and choosing Option [9].

Canadian customers can contact Rapid Response at (800) 932-3822. Remember any time you contact either monitoring station, you will need to provide your name, address, and your false alarm password or phrase. If you provide incorrect information when asked it will result in the dispatch of authorities.

If you have a support question about your alarm system or need to make changes to your account, the monitoring station cannot assist you with that. For those types of requests, send an email to support@alarmgrid.com with as many details as possible about what type of assistance you need. Remember that when we return after the holiday, there may be a bit of a support backlog. Please be patient and we will work through all requests as quickly as possible.

If you plan to enjoy fireworks as part of your July 4th celebration, be sure to use caution and follow any provided instructions for safety. We'll see you back here after the holiday, hopefully with all our phalanges and eyebrows intact! Thank you for trusting us with your safety, and the safety of your family. We very much appreciate you being a part of the Alarm Grid family.

Resideo and Honeywell Home, formerly Honeywell, released an announcement last week that they will change their date code format from a YDDD (Year, Day of the year) format, to use YYWW (Year, Week of the year). This is being done, ostensibly, to simplify the decoding of date codes for users.

Product date codes are important for determining whether a product is still under warranty, as well as whether it may be affected by a particular anomaly that may have occurred because of an issue in the manufacturing process. For Carbon Monoxide detectors, which always have a finite useful life, the manufacturing date code is important to help determine when a CO detector needs to be replaced, particularly if the detector doesn't include a feature to warn a user when its useful life is coming to an end. For all these reasons, it's important to be able to decode a date code.

Going all the way back to the Ademco days, Resideo products have used a date code where a letter signified the Year of manufacture, and a 3-digit number signified the day of manufacture. For example, 2022 has been signified by the letter F, so a date code of F159 would indicate a product was manufactured on the 159th day of 2022, or June 8. Calendars can be downloaded from the internet with all the days of the year enumerated.

Of course, this date code scheme has advantages and disadvantages. The letter used to signify each year can seem somewhat arbitrary, and at some point, letters must begin to be repeated. So, with a very long-lived product line, there could be some confusion as to whether a particular letter indicates the older or newer iteration of that letter for that product. The advantage of this format is that you know exactly which day a product was manufactured, and exactly which day it was packaged (packaging has its own date code, which follows the same format). This information can be helpful when determining a manufacturing issue.

Starting this month, June 2022, Resideo will standardize on a new Date Code format. In this format, containing four (4) digits, the first two (2) digits will indicate the year of manufacture, and the last two (2) digits will indicate the week of that year (YYWW). This will simplify things, as no one will have to look up or figure out which year goes with which letter, but it also doesn't supply quite as detailed an accounting of when a product was manufactured or packaged as the old format did. Packaging date codes will also be making the switch.

Below are some examples of the new Date Code, in these examples, the Date Codes are all 2223, indicating they were manufactured the 23rd week of 2022:

Effective in August of 2022, Alarm.com is ending sales of Alarm.Com Image Sensors (ADC-IS-220-GC and ADC-IS-300-LP). Alarm Grid has already discontinued these sensors due to the fact that they are in short supply, and no more of them will be produced. Only the Honeywell Home PROINDMV remains.

The 2GIG IMAGE3:

There was some overlap between the Alarm.com Image Sensor models, and the 2GIG and Qolsys Image Sensor models. I have confirmed with Alarm.com that the 2GIG and Qolsys models are also discontinued as of August, 2022. Currently, the only Image Sensors being offered by Alarm Grid are the DSC PowerG and Honeywell Home PROINDMV models which are discussed in more detail below.

Image sensors were a great idea that never really took off. The original image sensors, first offered by 2GIG and Alarm.com, did not have particularly good resolution or picture quality, which is probably one reason they weren't widely adopted by the DIY crowd. By the time the 2nd generation of these sensors came around, people were prepared to simply go with full-on video monitoring or to avoid capturing images altogether.

Both the second and third-generation image sensors that were offered by 2GIG, Qolsys, and Alarm.com had very good image quality. Combine that with Alarm Grid's policy of offering monitoring for image sensors without an additional price markup, and the image sensor was a viable alternative to the use of video cameras. An Alarm.com user could log into their account and perform a "peek-in", meaning they could request that a particular image sensor grab a picture of whatever it was able to see at that moment, and the image (actually two (2) images) would then be uploaded to the customer's alarm.com account for viewing. The sensor could also take images upon sensing motion after a particular period of inactivity, or upon an alarm. For full details on image sensor features and operation, check out this prior post.

DSC offers a couple of PowerG PIR Cameras that will work with the Qolsys IQ Panel 2 and IQ Panel 4 in addition to the DSC PowerSeries Neo panels with a PowerG Transceiver added. These are the DSC PG9934P, Indoor PIR Camera, and the DSC PG9944, Outdoor PIR Camera. These sensors work like any other PowerG Sensor with the Qolsys Panels. They can only capture images when the system is armed and the image sensor is active (not bypassed). They send their images to the panel, and then the first image is uploaded to Alarm.com. A total of ten (10) images are taken, and these images are stitched together by the panel into a sort of stop-motion video where each image can also be viewed individually. This is done via the panel screen itself. When used with the PowerSeries Neo panels, the DSC PIR Cameras can be used for Visual Verification only, they do NOT work like a regular image sensor with Alarm.com.

DSC PG9934P, Indoor Image Sensor:

DSC PG9944, Outdoor Image Sensor:

The Honeywell Home PROINDMV is a wireless PIR motion sensor with a camera built-in, just like the 2GIG, Qolsys, and Alarm.com image sensors were. The PROINDMV is currently only supported on the Resideo PROA7PLUSC, and Honeywell Home PROA7PLUS panels. There is no "peek-in" option for these image sensors. They can only capture images when they sense motion while the system is armed in Away mode. Images or videos are captured and uploaded to Total Connect 2.0 for viewing. The user can choose to receive either a still image or a 10-second video clip. You can read their full details of operation in our previous post.

Honeywell Home PROINDMV:

It seems like the era of the image sensor may be coming to a close, at least for now. Who knows, once we're through the global chip shortage, and the availability of components is back to normal, perhaps the humble image sensor will experience a revival. If so, DIYers may want to consider giving these sensors a try. They really are an excellent idea. They can be used for alarm verification in this age of increasing police resistance to alarm response, and they are cheaper, both initially and on an ongoing month-to-month basis, than video cameras.

An announcement on the AlarmNet360 page shows that they will send a remote reset command to some LTEM-PA, LTEM-PV, LTEM-PIA, and LTEM-PIV radios. This will occur today, Friday 04/15/22 between 2:00 pm - 3:00 pm ET. This may cause a trouble condition, and queued alarm reports could be sent.

It's unclear why this is being done. After a successful reset occurs, the radio will send an "E339-EXP. Module Power ON / Reset" message to the monitoring station. If the radio was in comm failure prior to the reset and any unsent alarm signals were queued, this reset may cause those alarm messages to be sent. These signals would show up immediately following the E339 signal at the central station. We assume this would also cause the same alarm messages to show up in Total Connect 2.0, and to be sent as notifications.

In addition, depending on how the panel is programmed, this event may cause the panel to display a bF or Check 103 message, and could also cause trouble beeping from the keypad. Disarming the system twice should clear the message and return the system to its normal state.

Resideo has been investigating an issue with a very small number of communicators. The LTE-CFV, HWF2V-COM, LTE-IV, LTE-L3V, and VISTA-21IPLTE with LTE-21V. In a few cases, starting on March 19, 2022, the Verizon LTE SIM has become locked, causing a comm failure, or secondary path failure.

A device with this issue will show the following symptoms: Locally at the device, the LEDs will flash regularly at a rate of two times per second (see video above). Through AlarmNet360, the affected devices will have checked in normally for the period leading up to March 19, 2022. Then beginning on that date, or on a subsequent date through March 28, 2022, a comm failure will be indicated. Once the comm fail indication appears, it will not clear, so if you've had a comm failure during this time that has restored, then your communication failure is not being caused by this issue.

In addition to the above evidence of an issue, the alarm panel that the communicator is connected to will have a trouble indication displayed. This may come in the form of a Check 103, or a bF on VISTA-20P and similar panels, and also the L3000 panel. For the L3000 panel, the bF will only show on an RF keypad, such as the 5828 or 5828V, the panel itself will show Check or Fault 103. To silence any trouble beeping, enter a disarm command at any panel keypad. These trouble messages can be caused by other things, not just this issue, so if you see one of these error messages and think you may be affected, be sure to contact your alarm dealer for further assistance.

Bear in mind that only the communicators listed above are affected, and that these are all Verizon SIM Cards. If you have an AT&T Communicator, you needn't worry about this issue. Also, for those who have a dual-path communicator with Ethernet connected, you will not necessarily see a Communication Failure message. Instead you will be notified of a Secondary Path Failure. Again, if you are affected by this issue, once the failure occurs, it will not restore. So if you've received a Secondary Path Failure that has since restored, then you experienced a separate issue.

Again, if you feel that you have been affected by this issue, contact your alarm dealer. They can confirm if you are affected and will be able to assist you in receiving a replacement SIM. Alarm Grid customers who are affected have already been contacted and replacement SIMs are on the way. If any further information becomes available, we'll update this post with further details.

ISC West, the security industry's largest trade show, was held this week in Las Vegas. This is the first year since the COVID-19 outbreak that the show is being held in person. We didn't attend the show this year, but based on what we've seen, JCI and Qolsys won the ISC West show in 2022.

Qolsys:

IQ Pro

Qolsys, Inc. which was acquired by Johnson Controls in 2020, premiered two brand new products, and reintroduced one more. The IQ Pro Panel is a hybrid wired and wireless system which targets large homes, and medium to large businesses. It combines the reliability of hardwired components with the range and versatility of the DSC PowerG Sensor lineup. The product is planned for release in Summer, 2022.

There is very little information available about the IQ Pro. The Press Release announcing the product, which was released by Johnson Controls, didn't even say for certain that it would be a Qolsys branded product, though with 'IQ' as a part of the name, we assume it will be. This panel will combine elements of the IQ Panel 4 with the DSC PowerSeries Neo, and a little bit of customer feedback thrown in. A couple of things we do know, the IQ Pro will offer the choice of either Ethernet or WIFI connectivity along with LTE. This panel has been designed with Alarm.com for Business in mind, to take advantage of all the extended features offered there.

IQ WIFI 6

The Qolsys IQ WIFI 6 was actually first introduced to us here at Alarm Grid last year. It is a product we thought was going to released then, but it was introduced at ISC West and should be available in Summer, along with the IQ Pro. The IQ WIFI 6 is is a router that uses 802.11 1/b/g/n/ac/ax WIFI-6 technology. It offers dual-end 2.4 GHz and 5 GHz MIMO mesh architecture on a Qualcomm Networking Pro 400 platform. It will integrate with Qolsys touchscreen panels, to allow a user to administer the network from there.

The IQ WIFI 6 will offer four (4) network partitions, including a Guest Network and a dedicated network for the end-user's WIFI devices. Both of these will switch automatically between 2.4 GHz and 5GHz for seamless optimization of WIFI performance. In addition to these partitions, there are two (2) private network partitions to be used by security and/or networking providers. By separating the security, surveillance, and smart home devices from the rest of the network, professional providers can cut down on disruptions caused by user error.

IQ Hub

The Qolsys IQ Hub has actually already been released, in a limited fashion within the last six (6) months or so. Presumably due to supply chain issues, Qolsys has tightly controlled how many of these panels are shipped, but now, based on a press release this week, it seems like they may be looking to perform a wider release. The IQ Hub differs from the IQ Panel 4 in several ways, one of which is that each panel will only support one RF product line. There is a PowerG version with either an AT&T or Verizon communicator. This is the only version that has been released at this time. Soon however, there will be a version that supports unencrypted, uni-directional Honeywell and 2GIG wireless sensors, one that supports unencrypted, uni-directional Interlogix and all Qolsys wireless sensors, and a version that supports uni-directional DSC 433 MHz wireless sensors.

Resideo:

Cellbounce

Resideo and Honeywell Home brought the Cellbounce to ISC West. This device will bridge communicators that work on the AT&T 3G network over to the AT&T LTE network, without having to replace the device. This is a plug-n-play device. It connects to an outlet within range, which is 25' (7.62m), of the existing AT&T 3G communicator, though be sure not to plug the Cellbounce in until it has been configured by your alarm dealer.

It syncs to the 3G communicator, then with the LTE network and any signals sent by the communicator will be picked up and transported via LTE. It even works with Total Connect 2.0, though it does not work with two-way voice. It also only works in the contiguous United States, so Alaska, Hawaii, and Puerto Rico residents, the Cellbounce is not for you. There are some other caveats and limitations, so be sure to read our product description carefully before purchasing.

2GIG, Nortek Control:

2GIG Edge

In October of 2021 Nortek Control, the parent company of 2GIG, was purchased by Nice. Nice originated in Italy, with Nice North America handling the US and Canadian segment of the business. This year at ISC West, Nice put their stamp on this relatively new acquisition. In addition to some commercial camera innovations by Linear, Nice/Nortek Control announced during ISC West that they will offer exclusive integration between the 2GIG Edge security panel and the ELAN Home Control platform. The Edge has been out for about a year now. You can read all about it here.

According to their press release, this integration will be supported by the ELAN SC-100 and ELAN SC-300 system controllers running ELAN 8.7 OS (which won't be available until April, 2022). The 2GIG Edge panel requires firmware version 3.1.1.0 or later. Firmware can be pushed through Alarm.com or downloaded. This panel firmware version is not available from 2GIG just yet, but once it is posted, our page will be updated. One of the more convenient features of this integration is the ELAN Control Auto Zone Detection feature. If the ELAN system is setup first, with zone names, once the 2GIG Edge is installed, it can download all zones and zone names directly from ELAN, without having to re-enter the information.

Final Update: Per a restoral announcement, this issue was resolved by 11:45 AM

Update 10:56 AM: According to Resideo, these notifications are the result of "catch-up" notifications from the outage earlier this week. As the queue for these old messages clears out, the erroneous messages should taper off. In the meantime, actual disarm photos may be delayed.

Original Post: We've had multiple reports this morning of Honeywell Lyric users who are receiving disarm photos from their panels every few minutes. Even users who don't have notifications enabled for disarm photos are being bombarded via the activity log. If you are affected, ignore disarm photo notifications for now.

Initially, it was only Lyric users who were reporting this issue, but now we've received reports from users of the Pro Series panels as well. It seems to be Push Notifications that are being affected. To disable Push Notifications for now, do the following:

1. Log into Total Connect 2.0.
2. Go to More > Settings > Notifications.
3. Tap the toggle for Push Notifications so that it is disabled.

We'll provide more details as they become available.