PowerG Smoke Detectors Posts

Posted By

We're checking out the best environmental sensors for our top security system picks for the 2020 holiday shopping season, which are the Honeywell Lyric, the Qolsys IQ Panel 2 Plus, and the 2GIG GC3e. Environmental sensors include life-safety sensors, flood sensors, and temperature sensors.


If you haven't seen our alarm panel 2020 holiday buying guide or our security sensor 2020 holiday buying guide, then be sure to go and check those out, as they will give a nice introduction to this buying guide for environmental sensors. You will need to make the same compatibility considerations for environmental sensors as you do for security sensors. The sensors you choose must be compatible with your system and communicate at a wireless frequency that is accepted by the alarm panel you are using.

As a refresher, here are the compatible sensor lineups for our recommended systems. Just like last time, the sensor lineups that are italicized and underlined represent the encrypted sensors that provide extra wireless security and protection.

While security sensors look for signs of forced entry and unauthorized access, environmental sensors look for undesirable environmental conditions. Specifically, we offer environmental sensors that look for life-threatening conditions, such as a fire or the presence of carbon monoxide (CO) gas. We also offer environmental sensors for detecting floods, water leaks, and unusually high or low temperatures that indicate a broken HVAC system. We will cover each type of environmental sensor in greater detail later in this holiday buying guide.

Adding environmental sensors to your system offers a few advantages. For one, it makes your alarm system more versatile so that it is looking for more than just security breaches. You will also be able to check off more boxes on your certificate of alarm (CoA), and that could lead to bigger savings on your home owner's insurance. Make sure to check with your insurance company to see if that is the case.

Life-Safety Sensors

Life-safety sensors monitor for unsafe environmental conditions that could result in a loss of life. Specifically, this group is primarily comprised of smoke and heat detectors and carbon monoxide sensors. There are also special combination sensors and listening modules that we will discuss further down the line.

First, we will take a look at some of our most popular smoke and heat detectors. These sensors monitor for both the smoke and extremely high temperatures associated with a fire. It is recommended that you have at least one (1) of these sensors on each floor of your building, particularly inside of sleeping areas and in central and connecting areas such as living rooms and hallways.

When checking out these sensors, you might also look for one-go-all-go functionality. This means that when one detector on the network activates, all of the other compatible sensors on the network will also activate their sounders. This can be very important for ensuring that everyone is alerted to the emergency. Certain jurisdictions may require one-go-all-go as part of building codes, so check with your local fire marshal to see if that is the case.

Here are our top picks for smoke and heat detectors.

Sensor Name
Product Lineup
Compatibility
Range
Encryption
Notes
Honeywell SiXSMOKE

Honeywell SiX Series Lyric 300 Nominal Feet 128-bit AES Encrypted photoelectric smoke detector and 135°F fixed temperature and 15°F per minute rate-of-rise heat detector w/ 85 dB sounder. Supports One-Go-All-Go.
DSC PG9936

PowerG All IQ Panel 2 Plus 2,000 Feet Open Air 128-bit AES Encrypted photoelectric smoke detector and 135°F fixed temperature heat detector w/ 85 dB sounder. Supports One-Go-All-Go.
2GIG SMKT8e-345

2GIG eSeries 2GIG GC3e 350 Nominal Feet 2GIG eSeries encryption Encrypted photoelectric smoke detector and 15°F per minute rate-of-rise heat detector when fixed temperature is 104°F or higher w/ 90 dB sounder and freeze detection at 40°F.
Honeywell 5808W3

Honeywell 5800 Series Lyric, GC3e, 345 MHz IQ2+ 200 Nominal Feet None Non-encrypted photoelectric smoke detector and 135°F fixed temperature heat detector w/ 85 dB sounder and freeze detection at 41°F.

Now let's look at carbon monoxide sensors. These devices respond upon detecting unusually high levels of carbon monoxide (CO) gas. This gas is both odorless and tasteless, making it virtually impossible to detect without a proper sensor. The gas is extremely harmful to humans, and it can result in serious injury or death in a matter of minutes. We recommend installing at least one CO detector on each floor of your home or office. They are often installed outside of garages and furnace rooms where CO events are most likely to occur.

Here are our top picks for carbon monoxide sensors.

Sensor Name
Product Lineup
Compatibility
Range
Encryption Notes
DSC PG9933

PowerG All IQ Panel 2 Plus 2,000 Feet Open Air 128-bit AES PowerG CO Detector w/ 85 dB sounder.
2GIG CO8e

2GIG eSeries 2GIG GC3e 350 Nominal Feet 2GIG eSeries encryption 2GIG eSeries CO Detector w/ 85 dB sounder.
Honeywell 5800CO

Honeywell 5800 Series Lyric, GC3e, 345 MHz IQ2+ 200 Nominal Feet None Honeywell 5800 Series CO Detector w/ 85 dB sounder.
2GIG CO8

2GIG 345 MHz Series Lyric, GC3e, 345 MHz IQ2+ 350 Nominal Feet None 2GIG CO Detector w/ 85 dB sounder.
Qolsys IQ Carbon

Qolsys 319.5 MHz Series 319.5 MHz IQ Panel 2 Plus 300 Nominal Feet None Qolsys CO Detector w/ 85 dB sounder.

We also want to give some special recognition to some combination smoke and CO detectors from Honeywell. These sensors combine fire detection with carbon monoxide detection into one convenient life-safety device.

Here are our top picks for combination smoke and CO detectors.

Sensor Name
Product Lineup
Compatibility Range
Encryption Notes
Honeywell SiXCOMBO

Honeywell SiX Series Lyric 300 Nominal Feet 128-bit AES Encrypted photoelectric smoke detector and 135°F fixed temperature heat detector and CO detector w/ 85 dB sounder. Supports One-Go-All-Go.
Honeywell 5800COMBO

Honeywell 5800 Series Lyric, GC3e, 345 MHz IQ2+ 200 Nominal Feet None Encrypted photoelectric smoke detector and 135°F fixed temperature heat detector and CO detector w/ 85 dB sounder and freeze detection at 41°F.

Lastly, we want to mention a pair of listening modules. These devices actively listen for the Temporal 3 (T3) sound of an activated smoke detector or the Temporal 4 (T4) sound of an activated carbon monoxide sensor. These are commonly used with wired smoke detectors and CO detectors that would otherwise have no way of interfacing with an alarm system. If your smoke detectors or CO detectors are one-go-all-go, then, a single listening module can take over your entire wired detector network.

Here are our top picks for smoke & CO listening modules.

Sensor Name
Product Lineup
Compatibility
Range
Encryption
Notes
Encore FireFighter FF345

Encore 345 MHz Series Lyric, GC3e, 345 MHz IQ2+ 200 Nominal Feet None Offers both T3 Detection for Fire & T4 Detection for CO
Interlogix SLX-AD-T3
Legacy Interlogix 319.5 MHz 319.5 MHz IQ Panel 2 Plus 200 Nominal Feet None Only offers T3 Detection for Fire. Not for use with CO detectors.

Flood Sensors

Next, we'll be looking at flood sensors. These devices use probes to detect water caused by a flood or leak. It only takes a small amount of liquid to activate one of these sensors, so your system will be alerted before any serious damage occurs. Many of these sensors double as temperature sensors, so expect to see quite a bit of cross-over with that section as well. For best results, use your flood sensors in low-plane areas where leaks are likely to occur, such as underneath toilets, water heaters, and in basements. You might also see that some flood sensor have a reporting delay that is used for false alarm prevention. This will be listed in the notes section in the table when applicable.

Let's check out our top picks for flood sensors.

Sensor Name
Product Lineup
Compatibility
Range
Encryption
Notes
DSC PG9985

PowerG All IQ Panel 2 Plus 2,000 Feet Open Air 128-bit AES PowerG Flood Sensor w/ 6-Foot Detection Probe.
2GIG FT6e-345

2GIG eSeries 2GIG GC3e 350 Nominal Feet 2GIG eSeries Encryption 2GIG eSeries Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.
Qolsys IQ Flood-S

Qolsys S-Line Series 319.5 MHz IQ Panel 2 Plus 600 Nominal Feet Qolsys S-Line Encryption Qolsys S-Line Flood Sensor w/ 6-Foot Detection Probe. Has a 1 to 3 minute reporting delay.
Honeywell 5800FLOOD

Honeywell 5800 Series Lyric, GC3e, 345 MHz IQ2+ 200 Nominal Feet None Honeywell 5800 Series Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 45°F. Has a 25 second reporting delay.
2GIG FT6-345

2GIG 345 MHz Series Lyric, GC3e, 345 MHz IQ2+ 350 Nominal Feet None 2GIG 345 MHz Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.

Temperature Sensors

The final type of environmental sensors we'll be checking out are temperature sensors. These sensors look for unusually high or low temperatures that indicate a broken HVAC system. When a temperature sensor is used for high-temperature detection, it should not be confused with a heat detector that looks for extreme temperatures only associated with fires. Instead, the high-end for a temperature sensor will usually activate at around 90°F. When a temperature sensor is used for low-temperature detection, it will sometimes be referred to as a freeze sensor. On the low-end, a freeze sensor will typically activate at a slightly higher than the temperature at which water freezes, which is 32°F. This is done to give the end user a bit of notice so that they can take action before the pipes freeze. You can typically expect a freeze sensor to activate between 40°F and 45°F. Most temperature sensors will offer both high and low temperature detection. And just like in the previous category, there is a lot of crossover with flood sensors, so you may see some repeats from the previous selection.

Here are our top picks for temperature sensors.

Sensor Name
Product Lineup
Compatibility
Range
Encryption
Notes
DSC PG9905

PowerG All IQ Panel 2 Plus 2,000 Feet Open Air 128-bit AES PowerG Temperature Sensor w/ customizable high and low temperature detection.
2GIG FT6e-345

2GIG eSeries
2GIG GC3e
350 Nominal Feet
2GIG eSeries Encryption
2GIG eSeries Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.
Qolsys IQ Temp-S

Qolsys S-Line Series 319.5 MHz IQ Panel 2 Plus 600 Nominal Feet Qolsys S-Line Encryption Qolsys S-Line Temperature Sensor w/ High Temperature Detection @ 100°F and Low Temperature Detection at 40°F.
Honeywell 5800FLOOD

Honeywell 5800 Series
Lyric, GC3e, 345 MHz IQ2+ 200 Nominal Feet
None
Honeywell 5800 Series Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 45°F. Has a reporting delay of 25 seconds.
2GIG FT6-345

2GIG 345 MHz Series
Lyric, GC3e, 345 MHz IQ2+
350 Nominal Feet
None 2GIG 345 MHz Flood Sensor w/ High Temperature Detection @ 95°F and Freeze Detection @ 41°F.

Contact Us

Remember to contact us if you have any questions about environmental sensors or their compatibility. The best way to reach us is to email support@alarmgrid.com. This is also a good email to use if you are interested in starting new monitoring service. Remember that we are available to check email from 9am to 8pm ET M-F. We look forward to hearing from you!

Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Comments


Posted By

You have likely heard us talking about the benefits of PowerG Sensors at one point or another. Today, we figured we would break down the benefits of these sensors and explain why we like them so much. Let's take an in-depth look at PowerG Sensors and all of their wonderful benefits.


PowerG Sensors were originally designed for the hardwired DSC PowerSeries NEO Systems. By adding a compatible transceiver unit to your PowerSeries NEO, the system will be able to support PowerG Sensors. Johnson Controls, which you may know as the parent company of DSC, took the technology associated with PowerG Sensors, and brought it over to the Qolsys IQ Panel 2 System. This move was not a major surprise, as Johnson Controls also had partial ownership over Qolsys at the time, and Johnson Controls has since bought out Qolsys entirely.

The addition of PowerG support for the IQ2 marked the beginning of the Qolsys IQ Panel 2 Plus, which is how the system is still marketed and sold today. PowerG support is also available for the DSC Iotega, though that panel has largely flopped due to its lack of local end user programming. Today, the Qolsys IQ Panel 2 Plus represents the most popular panel for supporting PowerG. All versions and variants of the IQ Panel 2 Plus support PowerG Sensors, and their exceptional performance makes them the go-to choice for IQ2+ users who want equipment with the best versatility and protection.

Starting with the range, PowerG Sensors can be used from up to 2,000 feet away from the IQ Panel 2 Plus when they are used in an open air environment. By open air environment, we are talking about a perfect setting with a direct line of sight, and no obstacles between the sensor and the alarm panel. Most homes and businesses do not provide the ideal, "open air" environment, as there are usually walls and metal appliances present. When you see us mention that 2,000 feet open air range, take that with a grain of salt, because in practice, the range is likely a bit less. But still, we can undoubtedly say that PowerG offers arguably the best wireless range in the security industry. Even if its nominal range isn't quite as far as its "open air range", it is still a very powerful signal that can help you overcome the range issues that other sensor lineups may experience. It is great for use in detached garages, barns, multi-building complexes, and even just large industrial buildings.


To make matters even better, there is also a PowerG Repeater, the PG9920. This device will effectively double the range of any PowerG Sensor and help you overcome range limitations caused by thick walls and other obstacles or signal disruptions. The repeater works by taking the signal sent out from any PowerG Sensor and sending it out a second time with just as much power and force as when it was first sent from the original sensor. By strategically placing the repeater, it's theoretically possible to double the useful wireless range of these sensors. That would mean that they can be used from up to 4,000 feet away from the IQ2+ in an open air environment. And if your building is particularly large, you may even have repeaters going away from the IQ Panel 2 Plus System in different directions, including up and down in building stories above or below.

But PowerG Sensors offer more than just an impressive wireless range. They are also known for their exceptional security. This is thanks to their military grade 128-bit AES encryption. To put this as simply as possible, the PowerG Sensor and the panel share a unique encryption key at the time of pairing. The sensor must provide this encryption key to the panel whenever it transmits a signal. Additionally, the panel must then provide a return response with the encryption key as verification in order for the command to go through. In the past, we have referred to this two-way communication process as a "digital handshake". Because of this encrypted pairing process, a PowerG Sensor actively knows whether or not it is currently paired with a panel. You may need to factory default a PowerG Sensor before you can pair it with a new system.


PowerG Sensors also take proactive measures against RF jamming. When a wireless sensor communicates with an alarm panel, it does so at a certain wireless radio frequency (RF). When we talk about RF jamming, we are referring to any malicious technique that prevents wireless signals from reaching their intended destination. This is accomplished by blocking the receiver with a stronger signal at the same wireless frequency as the device that is legitimately trying to communicate with it. When this is done on an alarm system, the system doesn't receive the incoming signals from faulted sensors, and no action is taken during a security breach or an unfavorable environmental condition. Early wireless sensors did not take this into account, and this made RF jamming an effective way to defeat an older wireless system.

The way that PowerG Sensors overcome RF jamming techniques is through a process called Frequency Hopping Spread Spectrum (FHSS). This process involves splitting the RF bandwidth into multiple channels. Each independent channel represents a unique radio frequency for wireless communication to occur. The transmitter (the PowerG Sensor) and the receiver (the alarm panel) both agree on a set of channel hopping sequences that will take place. These sequences are encrypted and time-based for them to occur seamlessly. Since the transmitter and the receiver are both synchronized, they can switch between channels very rapidly. A potential intruder would never be able to re-tun an RF jamming device to keep up. In the case of the PowerG Sensors, the frequency hops occur between 912 MHz and 918 MHz. There are 50 different unique frequency channels that are used, and frequency switches occur 64 times per second. More information on FHSS is available here.

One other benefit of PowerG Sensors that we have never discussed previously is their Adaptive Transmission feature that helps them conserve battery life. This is why you will often see a PowerG Sensor with a very long expected battery life, sometimes more than ten (10) years). Adaptive Transmission involves two-way communication between the PowerG Sensor and the alarm panel. The alarm panel will tell the PowerG Sensor how well its signal is being received. The PowerG Sensor can then adapt its outgoing signal so that it reliably reaches the panel, without expending too much energy. The sensor and the panel regularly exchange this information so that the ideal amount of energy is always used in signal transmissions. This saves battery life in the long run.

We have also found that PowerG Sensors are extremely easy to enroll and they offer the reliable and effective performance that you should expect out of your security system. We wholeheartedly recommend them for use on the Qolsys IQ Panel 2 Plus, as well as any other compatible alarm system. It is expected that the upcoming Qolsys IQ Hub will also be able to utilize PowerG Sensors, so look forward to using PowerG Sensors on that panel once it is available.


For now, if you have any questions about PowerG Sensors or the systems that support them, or if you are interested in signing up for new alarm monitoring service, then please reach out to us by emailing support@alarmgrid.com. We'll be available to check your emails from 9am to 8pm ET M-F. We look forward to hearing from you!

Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Comments


Posted By

If you're using a newer wireless security system, then you will definitely want to explore the encrypted sensor options that we offer! Encrypted sensors are virtually impossible to hack, and they can make your security system even more secure. There are many great options available.

Honeywell sixminictpk5 a 5 pack of sixminict encrypted wireless

As you know, a home security system or a business security system is an investment you make for the protection of yourself, your property, and those around you. A proper system should also give you peace of mind and make you feel safe. It doesn't do you any good if an intruder manages to defeat your system. But with encrypted sensors, that is extremely unlikely to ever happen.

If you aren't familiar with encryption, it refers to techniques for encoding data and signals so that only authorized individuals and/or equipment are able to access the information. When it comes to wireless alarm systems, encrypted sensors send protected signals that can only be accessed, received, and interpreted by the authorized panel.

When wireless systems first rose to prominence, they rarely, if ever, used encryption. This made many people wary of wireless security panels, and they felt more secure using wired ones. The lack of encryption wasn't seen as a fatal flaw, as an intruder would have to be extremely savvy and really know what they're doing to defeat even a non-encrypted sensor. To this day, many people feel totally comfortable and safe using non-encrypted equipment. Remember, most intruders don't have the knowledge to beat wireless sensors, even if they aren't using encryption.

But there are the rare, professional criminals who do take the time to extensively study security equipment, and they develop techniques for beating non-encrypted devices. This is very uncommon, but it's not unheard of. And if you aren't using encrypted sensors, then you are leaving yourself open to this small risk. Whether or not that means outfitting your system with all-new encrypted sensors, or even upgrading to a different system that is capable of supporting encrypted sensors is up to you. We just want to make you aware of your options.

Today, we're going to briefly look at some popular wireless systems and explore their encrypted sensor options, as well as their non-encrypted sensor lineups. This will help you learn more about your system, or one you are considering for purchase.


Honeywell Lyric Controller

Honeywell lyric controller encrypted wireless security system


The Lyric represents the first the first encrypted panel from Resideo, formerly known as Honeywell. The system has its very own lineup of encrypted sensors called the Honeywell SiX Series Sensors. The lineup is a bit limited, as its lacking options like an outdoor door and window sensor and a curtain motion sensor. But the good news is that these sensors are extremely secure with their military grade 128-bit AES encryption.

You can supplement your SiX Series Sensors on your Lyric System with devices from the Honeywell 5800 Series. These sensors are not encrypted, but the lineup offers more diverse selection than the SiX Series lineup. You could consider using encrypted sensors for the most vulnerable parts of your home or office, while using non-encrypted 5800 Series devices for areas where it isn't as important. The non-encrypted 2GIG 345 MHz Sensors are also compatible with the Lyric once the system is on Firmware Version MR3 or higher.


Qolsys IQ Panel 2 Plus

Qolsys iq panel 2 plus verizon lte with powerg s line and legacy


There are some outstanding encryption options available for the Qolsys IQ Panel 2 Plus, regardless of which version you have. Any IQ Panel 2 Plus System can readily support DSC PowerG Sensors. Not only do these sensors have an outstanding wireless range of up to 2,000 feet away from the IQ Panel 2 Plus, they also utilize military grade 128-bit AES encryption and Frequency Hopping Spread Spectrum (FHSS) technology.

And if you have the 319.5 MHz Version of the Qolsys IQ Panel 2 Plus, then you can also pair Qolsys S-Line Sensors, which use rolling code encryption. This rolling code encryption isn't quite as secure as the encryption used by PowerG Sensors, but it still does a good job of keeping your system protected. The S-Line Sensors will also utilize encryption when paired with the original Qolsys IQ Panel 2. The original IQ Panel 2 cannot use PowerG Sensors.

In terms of non-encrypted options, each IQ Panel 2 Plus can support one of three (3) non-encrypted radio frequency signals. The available options are 319.5 MHz, 345 MHz, and 433 MHz, and it is dependent upon which version of the IQ Panel 2 Plus you buy. Again, it is certainly possible to mix encrypted sensors with non-encrypted sensors on the same system. But with the diversity and selection of the PowerG lineup, you probably won't need to look outside too much.


2GIG GC3e

2gig gc3e wireless encrypted alarm panel


The big highlight when the 2GIG GC3e was introduced was its ability to support encrypted sensors. While it took a little while before its encrypted sensor lineup became available, we were very pleased with the result. The 2GIG eSeries Sensors use highly secure encryption to keep your system protected. It also seems that 2GIG is regularly expanding upon this lineup, as we have been seeing new eSeries Sensors hit the market it recent times. All of the 2GIG eSeries Sensors are compatible with the GC3e, as well as its little brother, the GC2e.

With the GC3e, you also get access to the Honeywell 5800 Sensors and the 2GIG 345 MHz lineup. Just like with the Lyric, there is a bit more of a diverse selection of non-encrypted sensors available for the 2GIG GC3e. You can definitely set up a mixture of encrypted and non-encrypted sensors to meet the needs of your business. But with new 2GIG eSeries offerings continuing to become available, you shouldn't have much trouble building a fully encrypted 2GIG Security System.


Alarm grid inside security stickers

If you are looking to set up an encrypted security system, then Alarm Grid is here to help! We can let you know if your existing system has any encrypted sensor options available. We can also help you determine if you are currently using encrypted devices or if your existing sensors are non-encrypted. Many users have trouble determining. Either way, we'll help you make an informed decision so that you can get the most out of your monitoring service. If you want to reach us, please email support@alarmgrid.com. We check our email from 9am to 8pm ET M-F. We look forward to hearing from you!

Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Comments


Posted By

Hi DIYers! We're here for our video recap. We only have three (3) new videos this week, but they all follow a theme. They all feature Joe discussing the PowerG Smoke Detectors. You can use them with any PowerG compatible panel, and they offer one-go-all-go technology! They are nice devices!

Dsc pg9916 powerg 915mhz wireless smoke and heat detector

Additionally, if you haven't seen our blog about the new DSC PG9936 Smoke and Heat Detector, make sure you take a look. Now, onto the videos!

Properly Testing a PowerG Smoke Detector

Joe shows you how to test a PowerG Smoke Detector. This is something you should do regularly, and you may have to perform this test to get a certificate of alarm (CoA). The PowerG Smoke Detectors have a test button so you can easily test transmissions with the panel. If you want to test the device for smoke detection, then you will need canned smoke. Make sure to put your system on test mode before testing!


Enrolling a PowerG Smoke Detector In a Qolsys IQ Panel 2 Plus

Joe shows you how to enroll a PowerG Smoke Detector with a Qolsys IQ Panel 2 Plus System. All versions of the Qolsys IQ Panel 2 Plus include a PowerG daughtercard for supporting PowerG Sensors. PowerG Smoke Detectors can be auto-enrolled with an IQ Panel 2 Plus System by putting the panel into its auto-enrollment mode and then holding down the device's enrollment button until the LED light remains steady. However, the new PG9936 can be auto-enrolled by powering the device on while the panel is in enrollment mode.


Factory Defaulting a PowerG Sensor

Joe shows you how to factory default a PowerG Smoke Detector. These same steps apply to almost any PowerG Sensor. The PowerG devices use 128-bit AES encryption in all their wireless communication. This requires linking the PowerG Sensor with a compatible panel. When you delete the sensor from the panel, the sensor will still think that it is enrolled with the panel. You need to perform a factory default on the PowerG Sensor so that it knows that it is no longer enrolled.

Tags: , , , , , , ,

Comments


Posted By

Hi DIYers! Today, we're taking a quick look at the new DSC PG9936 PowerG Smoke & Heat Detector. This device is great for anyone looking for a reliable fire-safety sensor for use with a PowerG-compatible System. The new sensor offers some impressive features, and it is super easy to use!


The DSC PG9936 replaces the older DSC PG9916. The new model features an updated designed and enhanced detection for improved functionality. However, most of the specs from the PG9916 return to the PG9936. If you have an existing PG9916, then it will continue to work just fine. But it's great to see a new smoke and heat detector available!

For smoke detection, the PG9936 uses photoelectric technology. This is arguably the most consistent and more reliable smoke detection method available, and it will help ensure that any fire is detected as quickly as possible. The sensor also features a built-in 135°F fixed temperature heat sensor for redundancy. This will give you peace of mind in knowing that any fire will be properly detected.

Any system that supports PowerG can use the DSC PG9936 Sensor. This includes any Qolsys IQ Panel 2 Plus and any DSC PowerSeries NEO with added PowerG Receiver. It can be easily auto-enrolled by putting the panel into its enrollment mode and then powering on the PG9936 by inserting its batteries. You are welcome to check out the PG9936 Install Guide for more information.

Also returning to the DSC PG9936 is one-go-all-go support. This means that if the sensor is activated, all other PowerG Smoke Detectors paired with the panel will also activate. This is very important for ensuring that everyone in the building is properly alerted to the fire. Remember that each PowerG Smoke Detector has an 85 dB sounder for alerting building occupants.

Each PG9936 uses three (3) AAA batteries for power (included), and has a three (3) battery life on average. The sensor features a tri-colored LED status light for assisting with enrollment and troubleshooting. It measures five (5) inches across and is 2.5 inches deep. There is a test button on the device for easy testing when needed. Remember to place your system on test mode first!

You can get the PG9936 from the Alarm Grid website right now! If you have any questions about the DSC PG9936 Smoke & Heat Detector or any of our other products, please email us at support@alarmgrid.com. Our support team checks emails between 9am and 8pm ET M-F. We look forward to hearing from you!

Tags: , , , , , , , ,

Comments